Having trouble with your Festool power tool? Well, we're here to help you. Before posting to the forum, give us a chance to diagnose and resolve your issue. In the U.S. and Canada, call us toll-free at 888-337-8600 on Monday-Friday between 8a-5p EST or contact us via email at service@festoolusa.com. For other countries, please visit http://www.festool.com for contact information for your local Festool service department.

Author Topic: Carvex for resawing?  (Read 19282 times)

0 Members and 1 Guest are viewing this topic.

Offline Mark Enomoto

  • Posts: 266
Carvex for resawing?
« on: September 07, 2013, 05:05 PM »
Any chance we will see an attempt to resaw using a Carvex? Not talking about a log, but raw lumber. Would speak to the ability of the Carvex to cut vertically.

Festool USA does not pre-approve the contents of this website nor endorse the application or use of any Festool product in any way other than in the manner described in the Festool Instruction Manual. To reduce the risk of serious injury and/or damage to your Festool product, always read, understand and follow all warnings and instructions in your Festool product's Instruction Manual. Although Festool strives for accuracy in the website material, the website may contain inaccuracies. Festool makes no representations about the accuracy, reliability, completeness or timeliness of the material on this website or about the results to be obtained from using the website. Festool and its affiliates cannot be responsible for improper postings or your reliance on the website's material. Your use of any material contained on this website is entirely at your own risk. The content contained on this site is provided for informational purposes only and does not constitute professional advice.


Offline windmill man

  • Posts: 671
Re: Carvex for resawing?
« Reply #1 on: September 07, 2013, 05:30 PM »
Who uses a jigsaw for re sawing [doh]

Offline SRSemenza

  • Global Moderator
  • *
  • Posts: 8470
  • Finger Lakes Region, NY State , USA
Re: Carvex for resawing?
« Reply #2 on: September 07, 2013, 05:50 PM »
Well if you need to resaw and you don't have a bandsaw.  Actually I did it with a TS55 once. It was a one time thing and needed a special set up of course.


Seth

Offline tjbnwi

  • Posts: 5618
  • Cedar Tucky Indiana
Re: Carvex for resawing?
« Reply #3 on: September 07, 2013, 06:11 PM »
I resaw with the TS at least once a week. Longest one was about 11', you do need some tapered shims to keep the clamps from closing the kerf when you helicopter the board.

Tom

Offline windmill man

  • Posts: 671
Re: Carvex for resawing?
« Reply #4 on: September 07, 2013, 06:19 PM »
Have used the TS55 and 75 many times for re sawing ,you do have to be a bit careful with the 75 and use the right blade .

Offline Upscale

  • Posts: 754
Re: Carvex for resawing?
« Reply #5 on: September 07, 2013, 08:06 PM »
Who uses a jigsaw for re sawing [doh]

Yeah, it does sound really out there doesn't it? But, you work with what you've got and if a jigsaw is it, done properly it might be possible.

Offline SRSemenza

  • Global Moderator
  • *
  • Posts: 8470
  • Finger Lakes Region, NY State , USA
Re: Carvex for resawing?
« Reply #6 on: September 07, 2013, 08:17 PM »
I resaw with the TS at least once a week. Longest one was about 11', you do need some tapered shims to keep the clamps from closing the kerf when you helicopter the board.

Tom


Yup . that is basically how I did it. But since that saw can plunge cut ( I used the anti- kick back stop) I simply left the board longer than needed, started and ended  with a plunge / unplunge. Leaving the ends uncut. That way the clamps can't close up on the kerf.

Seth

Offline Festool USA

  • Festool USA Employee
    FOG Administrator
  • *
  • Posts: 8373
    • Festool USA
Re: Carvex for resawing?
« Reply #7 on: September 07, 2013, 09:45 PM »
Not sure this is a suitable application for a jigsaw personally.  [unsure]

Offline elimelech12

  • Posts: 376
Re: Carvex for resawing?
« Reply #8 on: September 07, 2013, 09:56 PM »


I could see it as a possibility if the Carvex were mounted upside down under a table. Then you could attach a fence to the table as well. It seems very possible depending on the width of stock.
Sold my tools but kept a few Fes-tools...just in case.

Offline Festool USA

  • Festool USA Employee
    FOG Administrator
  • *
  • Posts: 8373
    • Festool USA
Re: Carvex for resawing?
« Reply #9 on: September 07, 2013, 10:47 PM »
I could see it as a possibility if the Carvex were mounted upside down under a table. Then you could attach a fence to the table as well. It seems very possible depending on the width of stock.

NAINA

Offline elimelech12

  • Posts: 376
Re: Carvex for resawing?
« Reply #10 on: September 08, 2013, 12:34 AM »
I could see it as a possibility if the Carvex were mounted upside down under a table. Then you could attach a fence to the table as well. It seems very possible depending on the width of stock.

NAINA

Haha...yet?  [wink]
Sold my tools but kept a few Fes-tools...just in case.

Offline Upscale

  • Posts: 754
Re: Carvex for resawing?
« Reply #11 on: September 08, 2013, 03:01 AM »
Not sure this is a suitable application for a jigsaw personally.  [unsure]
There's a number of jigsaw tables out there so it's not as off the wall as one might think. In the end, I'd think it would come down to the accuracy of the jigsaw when deciding if it's a viable idea.


« Last Edit: September 08, 2013, 03:03 AM by Upscale »

Offline elimelech12

  • Posts: 376
Re: Carvex for resawing?
« Reply #12 on: September 08, 2013, 03:02 AM »
Check this out...jigsaw table

Sold my tools but kept a few Fes-tools...just in case.

Offline jmbfestool

  • Posts: 6619
Re: Carvex for resawing?
« Reply #13 on: September 08, 2013, 03:25 AM »
Check this out...jigsaw table



They should really learn how to market their product better and it might not do to bad at selling!
  The box looks like its from Toys R us

Not seeing it up close so can't truelly comment! But from the video it seems like a handy little thing to have!

I like how small and light it looks and simply clamp it to your bench setup on site. 

I actually had to scribe 40mm of some architrave and skirting to fallow contour of the floor (normally use my planer for the skirting but forgot my planer) yesterday I used my carvex with angle base cutting upside down. 

This little thing could be handy scribing narrow pieces like architrave. 

How much is it? If its cheap might just get it to try out like!
*********************************************************************** [thumbs up]UK members click me
*********************************************************************** [thumbs up]

Offline Alex

  • Posts: 5676
Re: Carvex for resawing?
« Reply #14 on: September 08, 2013, 03:29 AM »
These tables are very common here in Europe. But I don't think the manufacturer of the jigsaw table above went through the trouble of getting it approved by UL in the States. They'll be in trouble if some American decides to cut himself and sue.

How much is it? If its cheap might just get it to try out like!

http://www.neutechnik-toolshop.com/

The problem is these things are made to look real handy when they demostrate them in videos. When you use them in person you very soon find out they're utter crap. Flimsy and inaccurate.
« Last Edit: September 08, 2013, 03:36 AM by Alex »

Offline Alexander Webb

  • Posts: 103
Re: Carvex for resawing?
« Reply #15 on: September 08, 2013, 03:42 AM »
€59 for basic and €139 for set €8 postage to usa. Made in Germany to boot.
http://www.neutechnik-toolshop.com/products/jigsaw-table-accessories/jigsaw-table-super-set/#cc-m-product-518644706459
« Last Edit: September 08, 2013, 03:44 AM by AlexR »

Offline jmbfestool

  • Posts: 6619
Re: Carvex for resawing?
« Reply #16 on: September 08, 2013, 03:49 AM »
These tables are very common here in Europe. But I don't think the manufacturer of the jigsaw table above went through the trouble of getting it approved by UL in the States. They'll be in trouble if some American decides to cut himself and sue.

How much is it? If its cheap might just get it to try out like!

http://www.neutechnik-toolshop.com/

The problem is these things are made to look real handy when they demostrate them in videos. When you use them in person you very soon find out they're utter crap. Flimsy and inaccurate.


Yeah that's what I'm thinking it will be like!  

Because looks like its tottally made out of plastic which will have alot of deflection! Sayin that!!

I'm wouldn't be using it for precise work!

The benefits I see are-   Its cheap so good for site

I can fix my milwuakee cordless jigsaw to it and leave it attached 90% time the jigsaw will be just left at a slight bevel/angle for scribing.    Then just get out of the van clamp it to a bench or something and scribe away! It doesn't need to be accurate for scribing its as accurate as the user surely.  I'm the one fallowing the line.   All I want is something to hold my jig saw because scribing something 2metres long about 70mm wide or narrower is just a pain.

The festool cms module is expensive and its to much setup to get basic table and module to just do couple scribes.  This little toy thing seems ideal to just throw out onto site in seconds.   No?
*********************************************************************** [thumbs up]UK members click me
*********************************************************************** [thumbs up]

Offline Deansocial

  • Posts: 2114
Re: Carvex for resawing?
« Reply #17 on: September 08, 2013, 04:12 AM »
Jmb, how you finding the Milwaukee cordless jigsaw? I used 1 the other day and it was utter crap. To cut straight you had to hold it at an angle, to follow a curve it was all o er the place and blade defection was huge

Offline Alex

  • Posts: 5676
Re: Carvex for resawing?
« Reply #18 on: September 08, 2013, 04:53 AM »
Its cheap so good for site

I can fix my milwuakee cordless jigsaw to it and leave it attached 90% time the jigsaw will be just left at a slight bevel/angle for scribing.    Then just get out of the van clamp it to a bench or something and scribe away! It doesn't need to be accurate for scribing its as accurate as the user surely.  I'm the one fallowing the line.   All I want is something to hold my jig saw because scribing something 2metres long about 70mm wide or narrower is just a pain.

The festool cms module is expensive and its to much setup to get basic table and module to just do couple scribes.  This little toy thing seems ideal to just throw out onto site in seconds.   No?

It's cheapness is exactly why it is not good for site. In the video they show how it works by using a small 2x2 one foot long and that works. But if you slap a 2 meter long piece on it, that plastic plate will break in two very soon.

I agree something like this is a lot easier and quicker to set up than a CMS. The problem is that despite what the manufacturer claims, in reality they are nowhere near the sturdiness a professional requires and will break very quickly.

At least the Wolfrcraft version is made out of metal. Amazon link It will stand up to a lot more abuse and you can use heavier pieces on it. I actually owned it and it survived a good 10 years. It lacks a blade guide though, so deflection was a concern.

I am not trying to discourage you from trying this thing out yourself JMB, just sharing my experiences. As I bought a couple of them myself in the past, I can see how they can come in handy with certain tasks. The problem is just that the build quality, especially with the plastic ones, is generally abominable. But as I haven't seen this one before, maybe it's better.

Offline Upscale

  • Posts: 754
Re: Carvex for resawing?
« Reply #19 on: September 08, 2013, 07:03 AM »
It's cheapness is exactly why it is not good for site. In the video they show how it works by using a small 2x2 one foot long and that works. But if you slap a 2 meter long piece on it, that plastic plate will break in two very soon.

The point is there are jigsaw tables out there, some metal too. Obviously, anyone looking for great precision or the ability to cut long sheets of wood on a regular basis is going to look for a different, more capable solution.

Offline Richard/RMW

  • Retailer
  • *
  • Posts: 1735
Re: Carvex for resawing?
« Reply #20 on: September 08, 2013, 09:26 AM »
I was not even aware the "jigsaw tables" were available. I have been planning to make one and this prompted me to search online, turns out there are a lot of different, mostly cheap looking, versions available. Rockwell also has a complete saw, does not require using your own jigsaw:



I have not had any experience with Rockwell tools, although the few I have picked up and played with at my local Lowes seemed to be pretty well made. Online reviews of this saw are totally mixed, from 0 to 5 stars and back.

For $179 I may try it out.

RMW
As of 10/17 I am out of the Dog business and pursuing other distractions. Thanks for a fun ride!

Offline Michael Kellough

  • Posts: 3394
Re: Carvex for resawing?
« Reply #21 on: September 08, 2013, 10:13 AM »
I keep my old Bosch 1582 going largely because I have the portable clamp-on table Bosch made for it. (Metabo had a very similar table for their saws back then)

The table is strong, cast aluminum, holds the saw securely via a quick acting thumb screw secured clamp. There are tabs that fit into the saw shoe. I keep the saw, table, Collins coping foot, circle cutting arm, and a large quantity of blades in a Sys 2. It takes less than a minute to open the Sys and start sawing as long as there is a sturdy table with an overhang to clamp the little jigsaw table to. If not, it can clamp onto a scrap secured to the MFT.

Offline Michael Kellough

  • Posts: 3394
Re: Carvex for resawing?
« Reply #22 on: September 08, 2013, 10:50 AM »
Jmb, how you finding the Milwaukee cordless jigsaw? I used 1 the other day and it was utter crap. To cut straight you had to hold it at an angle, to follow a curve it was all o er the place and blade defection was huge

I'd like to know too. Which version are you two using?

I bought the M12. I have a lot of other M12 stuff and found it for a good price but like Dean I find the blade deflection terrible. Not only is there no blade support system like on the Trion or the newest Bosch but it seems like the plunger supports are missing or never adjusted. I can wiggle the plunger (that the blade is attached to) back and forth. Running the blade full speed in air looks ridiculous. At least the trigger is VS and allows the cut to be started at slow speed but once you get going who knows what angle the cut will be? The plunger has nearly 5 degrees of lateral play...

Offline kmdwoodwork

  • Posts: 81
    • kmdwoodwork.com
Re: Carvex for resawing?
« Reply #23 on: September 08, 2013, 12:04 PM »
I recently made a router/jigsaw table top out of plywood for site use, it is just a piece of ply with maple edge band that clamps to a bench. I made the mounting for the tools like Timtool did in his systainer top box.

I use an old Bosch jigsaw and router that live in my trailer. I have only used it to test it out and am hoping it will work out well for the occasional use.

If anyone is interested i can dig it out and post some photos.

Offline Nikko

  • Posts: 23
Re: Carvex for resawing?
« Reply #24 on: September 08, 2013, 01:25 PM »
I'd be interested in having a look at the photos Keith

Offline jmbfestool

  • Posts: 6619
Re: Carvex for resawing?
« Reply #25 on: September 08, 2013, 01:32 PM »
Jmb, how you finding the Milwaukee cordless jigsaw? I used 1 the other day and it was utter crap. To cut straight you had to hold it at an angle, to follow a curve it was all o er the place and blade defection was huge

Yip it is utter crap!  You can't run it along a straight edge because the blade isn't dead inline with the jigsaw.  I had mine replaced because pendulum didnt work and both the blades where not inline with the base so I just assumed that's how they make them!

So you need to have the jig saw on an angle for it to go straight. Like Tokyo drift!  Heehee

The blade does wander easy and the base hasn't got a very positive 90° lock.  

I don't rate the jigsaw at all its pretty crap!  Hence why I thought I could leave it in this toy of a jig permantly cus I never use the jigsaw.  Just gathers dust.

I wouldn't recommend it.  

Milwaukee 18M D-handle version  Michael
« Last Edit: September 08, 2013, 01:39 PM by jmbfestool »
*********************************************************************** [thumbs up]UK members click me
*********************************************************************** [thumbs up]

Offline elimelech12

  • Posts: 376
Re: Carvex for resawing?
« Reply #26 on: September 08, 2013, 04:02 PM »
You can also do a search for the MFTB that timtool built. He put a carvex in a homemade Systainer and it is awesome!

« Last Edit: September 08, 2013, 08:03 PM by elimelech12 »
Sold my tools but kept a few Fes-tools...just in case.

Offline kmdwoodwork

  • Posts: 81
    • kmdwoodwork.com
Re: Carvex for resawing?
« Reply #27 on: September 08, 2013, 04:55 PM »
I'd be interested in having a look at the photos Keith

I have to empty out my trailer in the morning so i can get to it and i will get some pics and try to post them later tomorrow.

Offline jmbfestool

  • Posts: 6619
Re: Carvex for resawing?
« Reply #28 on: September 08, 2013, 05:28 PM »
I'd be interested in having a look at the photos Keith

I have to empty out my trailer in the morning so i can get to it and i will get some pics and try to post them later tomorrow.


 [popcorn]
*********************************************************************** [thumbs up]UK members click me
*********************************************************************** [thumbs up]

Offline Michael Kellough

  • Posts: 3394
Re: Carvex for resawing?
« Reply #29 on: September 08, 2013, 08:49 PM »
Jmb, how you finding the Milwaukee cordless jigsaw? I used 1 the other day and it was utter crap. To cut straight you had to hold it at an angle, to follow a curve it was all o er the place and blade defection was huge

Yip it is utter crap!  You can't run it along a straight edge because the blade isn't dead inline with the jigsaw.  I had mine replaced because pendulum didnt work and both the blades where not inline with the base so I just assumed that's how they make them!

So you need to have the jig saw on an angle for it to go straight. Like Tokyo drift!  Heehee

The blade does wander easy and the base hasn't got a very positive 90° lock.  

I don't rate the jigsaw at all its pretty crap!  Hence why I thought I could leave it in this toy of a jig permantly cus I never use the jigsaw.  Just gathers dust.

I wouldn't recommend it.  

Milwaukee 18M D-handle version  Michael

The M18 jigsaw seems to be identical to the M12, just different battery packs.
Pity they didn't make them better.

Cordless isn't the issue. My old 18v Makita jigsaw is just as good as my corded Bosch. The cordless just doesn't last as long. It's at least twice as heavy and bulky as the M12 though. That's why I took a chance on the M12.

Offline tjbnwi

  • Posts: 5618
  • Cedar Tucky Indiana
Re: Carvex for resawing?
« Reply #30 on: September 08, 2013, 08:54 PM »
I resaw with the TS at least once a week. Longest one was about 11', you do need some tapered shims to keep the clamps from closing the kerf when you helicopter the board.

Tom


Yup . that is basically how I did it. But since that saw can plunge cut ( I used the anti- kick back stop) I simply left the board longer than needed, started and ended  with a plunge / unplunge. Leaving the ends uncut. That way the clamps can't close up on the kerf.

Seth

I insert the shims when the board gets flipped so I can resaw twice the saws capacity.

Tom

Festool USA does not pre-approve the contents of this website nor endorse the application or use of any Festool product in any way other than in the manner described in the Festool Instruction Manual. To reduce the risk of serious injury and/or damage to your Festool product, always read, understand and follow all warnings and instructions in your Festool product's Instruction Manual. Although Festool strives for accuracy in the website material, the website may contain inaccuracies. Festool makes no representations about the accuracy, reliability, completeness or timeliness of the material on this website or about the results to be obtained from using the website. Festool and its affiliates cannot be responsible for improper postings or your reliance on the website's material. Your use of any material contained on this website is entirely at your own risk. The content contained on this site is provided for informational purposes only and does not constitute professional advice.


Offline jmbfestool

  • Posts: 6619
Re: Carvex for resawing?
« Reply #31 on: September 09, 2013, 02:20 AM »
Jmb, how you finding the Milwaukee cordless jigsaw? I used 1 the other day and it was utter crap. To cut straight you had to hold it at an angle, to follow a curve it was all o er the place and blade defection was huge

Yip it is utter crap!  You can't run it along a straight edge because the blade isn't dead inline with the jigsaw.  I had mine replaced because pendulum didnt work and both the blades where not inline with the base so I just assumed that's how they make them!

So you need to have the jig saw on an angle for it to go straight. Like Tokyo drift!  Heehee

The blade does wander easy and the base hasn't got a very positive 90° lock.  

I don't rate the jigsaw at all its pretty crap!  Hence why I thought I could leave it in this toy of a jig permantly cus I never use the jigsaw.  Just gathers dust.

I wouldn't recommend it.  

Milwaukee 18M D-handle version  Michael

The M18 jigsaw seems to be identical to the M12, just different battery packs.
Pity they didn't make them better.

Cordless isn't the issue. My old 18v Makita jigsaw is just as good as my corded Bosch. The cordless just doesn't last as long. It's at least twice as heavy and bulky as the M12 though. That's why I took a chance on the M12.

Yeah the front design on the M12 looks the same I would assume it will perform very much the same as the M18 poorly.

I wouldn't take the risk if I was you unless you are able to get a hold of one and have a play around with it first.   The battery life on the M18 isn't bad last long enough so for cutting plywood on site or something rough its perfectly fine.  

If I get time ill make a little video of the M18
« Last Edit: September 09, 2013, 12:23 PM by jmbfestool »
*********************************************************************** [thumbs up]UK members click me
*********************************************************************** [thumbs up]

Offline Reiska

  • Posts: 1160
  • Hackers build things, Crackers break them.
Re: Carvex for resawing?
« Reply #32 on: September 09, 2013, 04:37 AM »
I tried resawing on my CMS-unit with the original Carvex PSC400 mounted in the CMS-PS insert upside down and using the CMS-TS55 fence as the guide fence. That didn't pan out very well due to the PSC400's inherent blade drift after about 5cm into the 2x4 board. This was most likely an attribute of the original Carvex's broken blade guide system so it actually might work with the 420.

Haven't had a chance to try this yet on my PS420, but my wife did some 'scroll sawing' of door signs out of 6mm plywood last weekend that actually worked unlike with the PSC400.
92161-0
The sky's the limit in my workshop, literally. [big grin]

Offline kmdwoodwork

  • Posts: 81
    • kmdwoodwork.com
Re: Carvex for resawing?
« Reply #33 on: September 10, 2013, 07:52 AM »
Okay, here is my cheap version of a router/jigsaw table. It is made from plywood with maple edgeband, it is mostly going to be used as a router table for site work but i figured while i was doing this i might as well add the jigsaw mount.

Even though i used quick clamps i wanted something more secure so i added the wooden piece that is screwed in because i really don't trust the cheap plastic clamps that i found in my shop. I don't plan on using this very often, just the couple of times during the year when i forgot to do something in the shop or when the need comes up.

I made this to attach to my miter saw stand but it can be clamped to just about anything in a pinch, when it is on the stand it also rests on the handle so it is actually supported on the front also.

This is in no way a precision piece but is was made with scraps in the shop and it does not take any additional room in my trailer.

92228-0

92230-1

92232-2

92234-3

92236-4

92238-5

92240-6

92242-7

Offline Michael Kellough

  • Posts: 3394
Re: Carvex for resawing?
« Reply #34 on: September 10, 2013, 09:47 AM »
Okay, here is my cheap version of a router/jigsaw table.

Good thinking to show this demonstration with a Bosch.

Offline Frank Pellow

  • Posts: 2748
  • Toronto, Ontario and Lake Pivabiska, Ontario
Re: Carvex for resawing?
« Reply #35 on: September 10, 2013, 10:27 AM »
Okay, here is my cheap version of a router/jigsaw table. 

Looks good.  I plan to make something similar.
Cheers,   
               Frank (Festool connoisseur)

Offline Frank Pellow

  • Posts: 2748
  • Toronto, Ontario and Lake Pivabiska, Ontario
Re: Carvex for resawing?
« Reply #36 on: September 10, 2013, 10:28 AM »
Any chance we will see an attempt to resaw using a Carvex? Not talking about a log, but raw lumber. Would speak to the ability of the Carvex to cut vertically.

Even I, who do almost everything with a jigsaw, would not attempt to re-saw lumber with one.
Cheers,   
               Frank (Festool connoisseur)

Offline tazprime38

  • Posts: 245
Re: Carvex for resawing?
« Reply #37 on: October 19, 2014, 02:02 PM »
So has anyone bought the neutechnik jisaw table? I am considering getting the full kit to use with my P1cc.  I could have done with one last week as I had to scribe rip architrave.  Done it freehand but that table would have saved a lot of messing around.

Just like jmb said it would be useful for scribing lengths of architrave and skirting.  Also ripping down small bits of wood etc. I don't ever take a table saw on site and this looks easy to set up and is compact to store and carry.

If anyone has used one I would like to know their views and experience.

Offline TinyShop

  • Posts: 182
Re: Carvex for resawing?
« Reply #38 on: January 08, 2018, 05:52 AM »
For posterity...





[Thanks @Acrobat for sharing your workaround!]

[Source for 1st photo]
[Source for 2nd photo]

Alternatively, it seems like a simple matter to build a plywood CMS insert expressly designed to accept the Neutechnik table (the plastic table could be reinforced from underneath quite easily to counter concerns of stability & longevity) such to allow the professional user the huge advantages of both an overhead blade guard/guide and above and below-the-table dust collection. For inspiration:



And, to pickup on what an earlier poster pointed out, how disappointing is it to discover that although a company like (the original) Triton so elegantly (and decades ago!) solved the issue of a jigsaw blade wandering when mounted upside down in a table...



...companies like Festool (and Bosch/Wolfcraf, etc.) stubbornly persist in offering substandard jigsaw tables (that lack an overhead blade guide & above-the-table dust collection)? I mean, just look again at what the poor bloke in the above photo had to cobble together just to make his jigsaw module* safe and (therefore) usable!

Like the MFT/3, the CMS table features a beefy extrusion that runs right round its perimeter - a great place to clamp an overhead arm assembly akin to what was included in the Triton jigsaw kit (such an assembly could even clamp to three sides for added stability). But, alas, such a worthwhile accessory doesn't exist.

My disappointment over this glaring absence is not unlike what I feel having just stumbled upon the fact that a) there was an earlier iteration of the CMS system (called "Basis") that b) featured not only t-slots on the face of at least three modules but c) a pull-saw module (!) that benefitted from proper knobs for raising, lowering and tilting the blade! Knowing this, how are the current CMS-TS modules (and the CMS base table itself) not a perfect example of devolution (rather than evolution)? Why are such worthwhile features missing from the CMS family? Anyone?

FWIW I am a (now somewhat disillusioned) owner of a CMS GE router table and a TS 75 module and someone who thought long & hard over the Precisio(s) and Mafell Erika (pull saws) before ultimately deciding on the CMS. And, similar to other dedicated CMS-TS owners, I've had to jury-rig a featherboard to the face of the miter gauge (the lack of even a single t-slot in the table unnecessarily complicates the addition of this obligatory safety feature), live without the safety benefits and added utility of a pull saw and fiddle around with setting blade angles. Plus, I've also decided against adding the CMS jigsaw module (and what would have been a new PS 300 EQ-Plus jigsaw) to my existing Festool collection. I'll stick to my Bosch, thank you very much, and devise something to incorporate a Neutechnik table into my CMS (building upon the former's blade guard/guide and above and below-the-table allowance for dust collection).   
« Last Edit: January 09, 2018, 07:54 PM by TinyShop »

Offline JimH2

  • Posts: 592
Re: Carvex for resawing?
« Reply #39 on: January 08, 2018, 09:35 AM »
The CMS system other than the router table is of questionable value unless someone is just intent on using all Festool even though better products exist. I have the CMS-VL and am happy with it. I keep an OF1400 in it and can change bits with it in the module. On the other hand tablesaw module is nearly 100% inferior than a small portable tablesaw. There are several models to pick from, but I have found the DeWalt ones to be the best with their geared fence, which once setup guarantees square cuts + easy repeatability.

Pluses:
Cheaper
Easier and quicker to setup.
Same footprint as the CMS module.
Is inclusive meaning everything you need to use it is included. The CMS requires more accessories to make it work.
Similar or slightly larger capacity.

Minuses:
For some it is not part of the system
Dust collection not as great.
No sliding table.
Depending on what you are cutting you might need to make a simple outfield table. I used a stack of systainers.

Offline TinyShop

  • Posts: 182
Re: Carvex for resawing?
« Reply #40 on: January 08, 2018, 01:21 PM »
On second thought...Neutechnik sells several of their jigsaw table components separately, including their Jumbo-Saw Extension-Accessory (Part #A07):

273388-0

...their Scroll Saw Adapter (A04):

273390-1

273392-2

...their Saw Dust Extraction Suction Adapter (A06):

273394-3

...and, of course, their extra-long jigsaw and specialty scroll saw blades.

All of the above and more (like the regular jigsaw guide head and some other gizmos) are included in the Neutechnik Jigsaw "Super Set", from which the various needed bits I am about to expound upon could be cannibalized (possibly offering some savings over purchasing the necessary parts separately). Used (often very lightly used) examples of the "Super Set" appear on ebay.de practically weekly and sell for about half what the same set new goes for.   

Anyways, here's my thought - the first item on the above list is designed to be bolted down to a work surface (IOW it is surface mounted) and it features what amounts to a customizable-length boom arm. I see this working well in conjunction with either a Festool Crown Stop (494369) - bolt the arm to the surface of the crown stop and then attach the co-joined assembly to the extrusion on the offcut side of the table - or,  if you already have one (which I happen to), in conjunction with the Festool Extension Table VB-CMS (493822); simply bolt the Jumbo Saw Extension accessory to the extension table (or, better yet, to a piece of plywood that clamps to the ext. table, the former maybe fitted with dual t-tracks to allow the Jumbo Saw Extension to slide along the lines of Tom's recent improvement to the combination of the CMS router fence and Woodpecker's Micro adjust).

Elevating the Jumbo Saw Extension on top of a section of plywood would also compensate for the absence of the Neutechnik table (with its thick profile). And, with the overhead boom arm mounted on the off-cut side of the table, the jigsaw module could benefit from the sliding table and miter fence as well as the Festool Stopper (a.k.a. "full length rip fence") LA-CS 50/CMS (492095).

Add in the overhead portion of Neutechnik's dust extraction system (used in collaboration with Festool's under-table system) and the ability to install and use Neutechnik's extra long jigsaw and scroll saw blades and...

...that would be a proper jigsaw table!

Darn it! This has me rethinking my opposition to the combination of the CMS-PS module and PS 300 jigsaw! ;) 
« Last Edit: January 09, 2018, 08:02 PM by TinyShop »

Offline Shadytree

  • Posts: 24
Re: Carvex for resawing?
« Reply #41 on: January 09, 2018, 05:36 AM »
A jigsaw in a table is a scroll saw & you can pick up a used one of those for a lot less money & effort than a carvex is some custom table is going to run.

Offline TinyShop

  • Posts: 182
Re: Carvex for resawing?
« Reply #42 on: January 09, 2018, 08:10 PM »
Ahhh @Shadytree...your suggestion assumes I have space for and/or want a dedicated machine (neither of which I do). Hence my focus on coming up with a work around for the CMS that allows me to make multiple uses of a single tool (a jigsaw). As others have pointed out before me, the real utility in the CMS unit comes from exploiting its potential. Along these lines, I've got a drill stand module in mind and, thanks to inspiration from other CMS aficionados on this forum, belt sander and RO sander modules as well. To each their own, right?