Timtool
Retailer
 Online
Location: Belgium Member Since: Mar 2011
Posts: 723
|
 |
« on: May 11, 2012, 03:48 PM » |
|
I just received today the accessory systainer i ordered for my Carvex (fantastic tool btw), now i think something is missing but i'm not certain.
Isn't there supposed to be some kind of "pin" to lock to the circle cutting compass in a hole? As is explained in the Carvex manual. I cannot find pictures of the full content, and theres not the usual content picture on the systainer lid interior.
Well if it is supposed to be there then it is missing, and what should i do?
As a side note, last week i received the centrotec installer kit from another dealer, and there was also a part missing, the long bit holder, i mailed the dealer about it and got no response.
|
|
|
|
|
Logged
|
TS55R, CT22E, CTLmini, Kapex KS120, ETS125, ETS150/5, RO150, RO90, CXS-set, T-15+3 set, DTS400, OF1010, OF2200 set, Carvex PS420 EBQ set, Centrotec installer set, LR32-sys, FS-800, FS-LR-1400x2, domino 500+domino sys, domino 700 XL, Surfix-sys, Sys-box 1, Syslite, LEV-350, Sys-box,MFTB/1-2-4... MFTC
|
|
|
Festool USA does not pre-approve the contents of this website nor endorse the application or use of any Festool product in any way other than in the manner described in the Festool Instruction Manual. To reduce the risk of serious injury and/or damage to your Festool product, always read, understand and follow all warnings and instructions in your Festool product's Instruction Manual. Although Festool strives for accuracy in the website material, the website may contain inaccuracies. Festool makes no representations about the accuracy, reliability, completeness or timeliness of the material on this website or about the results to be obtained from using the website. Festool and its affiliates cannot be responsible for improper postings or your reliance on the website's material. Your use of any material contained on this website is entirely at your own risk. The content contained on this site is provided for informational purposes only and does not constitute professional advice.
|
|
Shane Holland
Festool USA Employee FOG Administrator
Online
Location: USA Member Since: Jan 2007
Posts: 5006
|
|
« Reply #1 on: May 11, 2012, 03:51 PM » |
|
Tim,
It's stored in the circle cutter itself. You can see it barely in the back of this image, it's the green bit on the far right.
Edit: I should have mentioned to contact Festool Belgium about the missing part in your Centrotec Kit, and for this product if it's indeed missing.
|
|
|
« Last Edit: May 11, 2012, 03:58 PM by Shane Holland »
|
Logged
|
|
|
|
Timtool
Retailer
Online
Location: Belgium Member Since: Mar 2011
Posts: 723
|
|
« Reply #2 on: May 11, 2012, 04:13 PM » |
|
Thanks Shane, i will look tomorrow if it's there. Seeing it so small on that on that picture i can imagine i have overlooked it.
btw, i bought both kits in Germany because accessories are like 30% cheaper than here, but i still buy my tools at the local dealer.
|
|
|
|
|
Logged
|
TS55R, CT22E, CTLmini, Kapex KS120, ETS125, ETS150/5, RO150, RO90, CXS-set, T-15+3 set, DTS400, OF1010, OF2200 set, Carvex PS420 EBQ set, Centrotec installer set, LR32-sys, FS-800, FS-LR-1400x2, domino 500+domino sys, domino 700 XL, Surfix-sys, Sys-box 1, Syslite, LEV-350, Sys-box,MFTB/1-2-4... MFTC
|
|
|
Mat D
 Offline
Location: High Wycombe, UK Member Since: May 2011
Posts: 25
Carpenter Joiner Two sugars in my Tea
|
|
« Reply #3 on: May 11, 2012, 05:53 PM » |
|
Hi Tim, Snapped a couple of pics of mine if they are of help? Excuse the quality... Compass pin as you can see just slides in and out of the hole provided in the actual plastic body.   Mat |
|
|
|
|
Logged
|
|
|
|
Timtool
Retailer
Online
Location: Belgium Member Since: Mar 2011
Posts: 723
|
|
« Reply #4 on: May 12, 2012, 06:13 AM » |
|
thanks Mat,
i checked this morning and the part is indeed missing, i will send a mail to the dealer and report back.
|
|
|
|
|
Logged
|
TS55R, CT22E, CTLmini, Kapex KS120, ETS125, ETS150/5, RO150, RO90, CXS-set, T-15+3 set, DTS400, OF1010, OF2200 set, Carvex PS420 EBQ set, Centrotec installer set, LR32-sys, FS-800, FS-LR-1400x2, domino 500+domino sys, domino 700 XL, Surfix-sys, Sys-box 1, Syslite, LEV-350, Sys-box,MFTB/1-2-4... MFTC
|
|
|
Timtool
Retailer
Online
Location: Belgium Member Since: Mar 2011
Posts: 723
|
|
« Reply #5 on: May 14, 2012, 06:39 PM » |
|
little update, the dealer(Klaus Zeibig) that shipped me the installer set with a missing part has sent me the new part without asking any questions, very good service.
The other dealer who sent me the Carvex accessory set with a missing pin has replied that it needed to look under the insert and in the box, and that he personally packed it so everything has to be there. Even though it was the first thing i did when realizing something was missing, i did it again and found nothing.
Can someone tell me how tight or loose that pin sits in the circle jig? is it possible that it can fall out during shipping?
|
|
|
|
|
Logged
|
TS55R, CT22E, CTLmini, Kapex KS120, ETS125, ETS150/5, RO150, RO90, CXS-set, T-15+3 set, DTS400, OF1010, OF2200 set, Carvex PS420 EBQ set, Centrotec installer set, LR32-sys, FS-800, FS-LR-1400x2, domino 500+domino sys, domino 700 XL, Surfix-sys, Sys-box 1, Syslite, LEV-350, Sys-box,MFTB/1-2-4... MFTC
|
|
|
Kev
Offline
Location: Australia Member Since: Nov 2011
Posts: 2441
|
|
« Reply #6 on: May 15, 2012, 03:10 AM » |
|
little update, the dealer(Klaus Zeibig) that shipped me the installer set with a missing part has sent me the new part without asking any questions, very good service.
The other dealer who sent me the Carvex accessory set with a missing pin has replied that it needed to look under the insert and in the box, and that he personally packed it so everything has to be there. Even though it was the first thing i did when realizing something was missing, i did it again and found nothing.
Can someone tell me how tight or loose that pin sits in the circle jig? is it possible that it can fall out during shipping?
Unless there was a hole in your systainer - no. |
|
|
|
|
Logged
|
|
|
|
Mat D
Offline
Location: High Wycombe, UK Member Since: May 2011
Posts: 25
Carpenter Joiner Two sugars in my Tea
|
|
« Reply #7 on: May 15, 2012, 04:38 AM » |
|
Tim,
That pin fits pretty tightly in the store position within the jig as the first picture I posted shows. I couldn't imagine that coming out of there
on it's own accord.
Unless someone , somewhere went into the Sys before shipping and "borrowed" it (cough).........
It's just too much of a snug fit.
Mat.
|
|
|
|
|
Logged
|
|
|
|
jmbfestool
Online
Location: UK Member Since: Jan 2009
Posts: 5204
|
|
« Reply #8 on: May 15, 2012, 01:25 PM » |
|
Its a snug fit! It wont fall it itself
|
|
|
|
|
Logged
|
|
|
|
Timtool
Retailer
Online
Location: Belgium Member Since: Mar 2011
Posts: 723
|
|
« Reply #9 on: May 15, 2012, 03:17 PM » |
|
thanks guys, they are going to send me a new pin, though i have the impression they don't believe me. The guy said he is 100% certain it was there when he packed it, while you guys all say it cannot come loose on it's own. Well anyway it wasn't on the jig, nor in the systainer..
|
|
|
|
|
Logged
|
TS55R, CT22E, CTLmini, Kapex KS120, ETS125, ETS150/5, RO150, RO90, CXS-set, T-15+3 set, DTS400, OF1010, OF2200 set, Carvex PS420 EBQ set, Centrotec installer set, LR32-sys, FS-800, FS-LR-1400x2, domino 500+domino sys, domino 700 XL, Surfix-sys, Sys-box 1, Syslite, LEV-350, Sys-box,MFTB/1-2-4... MFTC
|
|
|
|
