Having trouble with your Festool power tool? Well, we're here to help you. Before posting to the forum, give us a chance to diagnose and resolve your issue. In the U.S. and Canada, call us toll-free at 888-337-8600 on Monday-Friday between 8a-5p EST or contact us via email at service@festoolusa.com. For other countries, please visit http://www.festool.com for contact information for your local Festool service department.

Author Topic: Mft/3 + which guide rail?  (Read 486 times)

0 Members and 1 Guest are viewing this topic.

Offline Brad1

  • Posts: 1
Mft/3 + which guide rail?
« on: February 07, 2018, 04:30 PM »
If I purchase a Festool 495315 MFT/3 Multifunction Table, can I use the 42" guide rail from the table with a 55" additional rail to rip an 8' sheet of plywood using two connector bars?  If not, what would be the next best solution?

Festool USA does not pre-approve the contents of this website nor endorse the application or use of any Festool product in any way other than in the manner described in the Festool Instruction Manual. To reduce the risk of serious injury and/or damage to your Festool product, always read, understand and follow all warnings and instructions in your Festool product's Instruction Manual. Although Festool strives for accuracy in the website material, the website may contain inaccuracies. Festool makes no representations about the accuracy, reliability, completeness or timeliness of the material on this website or about the results to be obtained from using the website. Festool and its affiliates cannot be responsible for improper postings or your reliance on the website's material. Your use of any material contained on this website is entirely at your own risk. The content contained on this site is provided for informational purposes only and does not constitute professional advice.


Offline Sparktrician

  • Posts: 3433
Re: Mft/3 + which guide rail?
« Reply #1 on: February 07, 2018, 04:49 PM »
If I purchase a Festool 495315 MFT/3 Multifunction Table, can I use the 42" guide rail from the table with a 55" additional rail to rip an 8' sheet of plywood using two connector bars?  If not, what would be the next best solution?

You're better off using two 55" rails joined together, and if you're going to do that, take a look at the LR 32 version of the 55" rail (493969).  You'll find it most useful if you get into cabinetmaking.  It's the same price as the 55" rail without the guide holes, so it's not a cost factor.  Just be sure that you use a 4' level as a straightedge when you join the rails to ensure that you get them properly aligned as you tighten down the screws. 
- Willy -

 "Remember, a chip on the shoulder is a sure sign of wood higher up." - Brigham Young

Offline live4ever

  • Posts: 640
Re: Mft/3 + which guide rail?
« Reply #2 on: February 07, 2018, 05:38 PM »
That gives you a 97" rail, which does not have enough room at the start and end of the rail for the saw.

Two 55" will work, as Willy said.  I did that for a long time.

Another solution is the 42" and the 75".  The 75" is a nice rail to have - it's a little more convenient for crosscutting sheets as I don't have to worry about perfect rail placement as with the 55".  Most people discover it when they get a TS75 as that's the rail that comes with it, but it's a really handy length.  The downside is you cannot get it in the LR32 flavor. 

"What you have to do tomorrow, do today.  What you have to do today, do now."  - a wise grandfather who was clearly talking about purchasing Festools

Offline rst

  • Posts: 1668
Re: Mft/3 + which guide rail?
« Reply #3 on: February 07, 2018, 06:28 PM »
I cut a lot of sheets.  If I could only have two rails it would be the 1900 and 3000.  I have all the rails but those are my most used. 

Offline Coen

  • Posts: 311
Re: Mft/3 + which guide rail?
« Reply #4 on: Yesterday at 10:25 AM »
+1 on the holey rail, although where I live, the LR32 rail is more expensive. But if plan on ever getting the LR32 set and contemplate buying a rail now, you might just as well buy the LR32 rail. That's what I did. I had the LR32 rail a few years before I got the LR32 Systainer.

That gives you a 97" rail, which does not have enough room at the start and end of the rail for the saw.

Two 55" will work, as Willy said.  I did that for a long time.

Another solution is the 42" and the 75".  The 75" is a nice rail to have - it's a little more convenient for crosscutting sheets as I don't have to worry about perfect rail placement as with the 55".  Most people discover it when they get a TS75 as that's the rail that comes with it, but it's a really handy length.  The downside is you cannot get it in the LR32 flavor.

Do you mean that the 1900 (75") comes with the TS75, or that people discover that they need/want it when they discover that the 1400 they got with their TS75 is just a bit too short?

Because everywhere I look, the TS75 is supplied with the 1400 (55")

Offline Corwin

  • Posts: 2461
Re: Mft/3 + which guide rail?
« Reply #5 on: Yesterday at 01:38 PM »
...
Do you mean that the 1900 (75") comes with the TS75, or that people discover that they need/want it when they discover that the 1400 they got with their TS75 is just a bit too short?

Because everywhere I look, the TS75 is supplied with the 1400 (55")

Here in the North American market the TS75 is shipped with the FS1900 guide rail. They used to ship the TS75 with the FS1400 rail, but changed to the FS1900 rail ten years ago.
Looks like your rabbit joint is a hare off! ;)