Author Topic: Kitchen Cabinet Work  (Read 1873 times)

0 Members and 1 Guest are viewing this topic.

Offline earcaesar1

  • Posts: 27
Kitchen Cabinet Work
« on: September 24, 2018, 02:16 PM »
Hey all,

I've trying to get in the planning stage of doing some kitchen cabinet remodeling. I am just a home owner and like to build things myself. I have the extra space at the top that I plan on turning my normal cabinets into full cabinets to the ceiling. The house was built in the mid 80's so matching the doors will be hard I think. I was looking to make a new door just a full cabinet length.

I was trying to find out a couple of things out. I am just trying to figure out what type of material to make the cabinets out of. They are stained and not painted. What type of plywood is used etc. The doors currently have raised panels. I am not sure 100% what design the wife will want, but what type of material is the panel typically made out of, same thing with the face frame parts. Looks like on the sides of the cabinet they have a 1/8 inch sheet of ply to cover up the screws.

I might can reuse the drawer fronts, not sure if I have to remake the drawers or not.

Tools I currently have is MFT, Domino 500, TS55, OF 1400, ETC 125, and a MIDI.

Edit:  I am looking to see opinions on if you would just try and add a new face for the part I am adding on to at the top or try and remove the old face on all the cabinets and make a new one for the whole thing?  The top cabinet I would make is top to bottom about 11.5" tall and spans the whole top of my kitchen. I would guess it would be around total worth of cabinets to make 30ft worth or so.

Thanks in advance for the feedback
« Last Edit: September 24, 2018, 03:03 PM by earcaesar1 »

Festool USA does not pre-approve the contents of this website nor endorse the application or use of any Festool product in any way other than in the manner described in the Festool Instruction Manual. To reduce the risk of serious injury and/or damage to your Festool product, always read, understand and follow all warnings and instructions in your Festool product's Instruction Manual. Although Festool strives for accuracy in the website material, the website may contain inaccuracies. Festool makes no representations about the accuracy, reliability, completeness or timeliness of the material on this website or about the results to be obtained from using the website. Festool and its affiliates cannot be responsible for improper postings or your reliance on the website's material. Your use of any material contained on this website is entirely at your own risk. The content contained on this site is provided for informational purposes only and does not constitute professional advice.


Offline tjbnwi

  • Posts: 5733
  • Cedar Tucky Indiana
Re: Kitchen Cabinet Work
« Reply #1 on: October 06, 2018, 10:48 PM »
@earcaesar1

I assume your reusing some of the existing cabinets? If not let us know.

You do not want to go to the ceiling with full height cabinets. Few ceilings are flat enough to allow this. Trims may need to be floated in.

Pictures of what exists please. Take a clear close up of the rail and stile profiles.

A photo showing the existing cabinets from 4-5’ also.

Thanks

Tom

Offline jobsworth

  • Posts: 5271
  • Does Anyone Know What Time It Is?
Re: Kitchen Cabinet Work
« Reply #2 on: October 07, 2018, 12:42 AM »
New cabinets I make the boxes out of 3/4 shop birch. Use end panels on the end of a run if the ends are exposed.

If you want face frame cabinets, what ever your wife decides best to use a hardwood.

The basics are Maple, Oak, Cherry, Alder, Hickory and Poplar for painted.

« Last Edit: October 07, 2018, 12:46 AM by jobsworth »

Offline Billedis

  • Posts: 613
Re: Kitchen Cabinet Work
« Reply #3 on: October 07, 2018, 03:32 PM »
If you are making new full height uppers, make the top rail 4 1/2" so you will have a good nailer without getting into the doors.

Re: Kitchen Cabinet Work
« Reply #4 on: October 30, 2018, 06:41 AM »
If you need some design Inspiration, why not take a 360 tours of our Belfast kitchen showroom which has been newly renovated. All Starplan fitted kitchens & fitted bedrooms are made in our very own factory in Dungannon. This means we can build to your own personal specifications and requirements.