Author Topic: material for slab doors  (Read 2744 times)

0 Members and 1 Guest are viewing this topic.

Offline mrFinpgh

  • Posts: 226
material for slab doors
« on: November 16, 2016, 10:01 PM »
I'm going to be doing some kitchen doors and drawer fronts in walnut, and I was wondering what folks think is the better material for slab doors:  plywood or mdf?   Nothing should be wider than 27" in this case.

Also, what are folks paying for Walnut ply these days?   I've got one shop quoting me over 170/sheet for PS A1, while I'm seeing $130ish elsewhere.   

Thanks,
Adam


Festool USA does not pre-approve the contents of this website nor endorse the application or use of any Festool product in any way other than in the manner described in the Festool Instruction Manual. To reduce the risk of serious injury and/or damage to your Festool product, always read, understand and follow all warnings and instructions in your Festool product's Instruction Manual. Although Festool strives for accuracy in the website material, the website may contain inaccuracies. Festool makes no representations about the accuracy, reliability, completeness or timeliness of the material on this website or about the results to be obtained from using the website. Festool and its affiliates cannot be responsible for improper postings or your reliance on the website's material. Your use of any material contained on this website is entirely at your own risk. The content contained on this site is provided for informational purposes only and does not constitute professional advice.


Offline Bert Vanderveen

  • Posts: 356
Re: material for slab doors
« Reply #1 on: November 17, 2016, 06:34 AM »
That price difference may reflect the quality of the veneers. And/or the execution style (mirrored, whatever). I would try to have a look at the stuff in person.
Cheers, Bert Vanderveen

TS55 · TS55R · OF1010 · DF500 Mk2 · MFT/3 + CMS TS55 + CMS PS300 + LA-CS 70/CMS · CTL Midi · RTS400 EQ · 2 x CXS Li 1,5 · T15+3 Li 4,2 · TI15 Impact Li 4,2 · PSB300 · LR32-SYS · RO150 · Kapex KS120 · 2 x MFK700 · RO90 · OFK700 · BS75 · OFK500 … | Hammer A3 31 Silent Power · Hammer N4400 

Offline mrFinpgh

  • Posts: 226
Re: material for slab doors
« Reply #2 on: November 18, 2016, 01:05 PM »
That's a good point.

I got a quote of $125/sheet from another local distributor.  So now I have two local places I can go look at.

Ultimately, it's not going to add up to a big difference in cost but I like to avoid overpaying where possible.

I also inquired about some interesting wood grained Panolam, just to explore my options.   Prices on that seem very reasonable, but anything special means buying a full unit.   I can't imagine using up 40 sheets of Melamine any time soon.

-Adam



Offline slalom

  • Posts: 37
Re: material for slab doors
« Reply #3 on: November 27, 2016, 05:36 PM »
I used solid poplar for the core of my doors, the edges in maple and a thick maple veneer on my slab doors. As the poplar is cut in 2 inch strips with the grain perpendicular to the width of the door they have been very stable.

I used Lee Valley 2002GF glue, similar to Titebond III.

The doors are heavy, with a solid feel. I used three heavy stainless steel hinges on each.

Offline Bob Wolfe

  • Posts: 80
Re: material for slab doors
« Reply #4 on: November 27, 2016, 10:59 PM »
My kitchen is all slab doors, wood grain Panolam, "hard rock maple"pattern, 10 plus years, no major issues but the odd nick is now visable, super easy to clean.

Get a local shop to order them for you is you can't purchase less than 40 sheets, their markup likely not too bad.