Author Topic: Systainer dividers  (Read 13484 times)

0 Members and 1 Guest are viewing this topic.

Offline Greg Powers

  • Posts: 2283
  • Metric convert
    • Stargate Unofficiial
Systainer dividers
« on: March 14, 2014, 07:25 PM »
Found these on the Woodcraft website (on sale and on clearance). They work great for storing Ro90 sandpaper in a Sys II. Much better access then the Festool stacking solution that is in a Sys I
Greg Powers
Size:XL

Offline P2P

  • Posts: 50
Re: Systainer dividers
« Reply #1 on: March 14, 2014, 07:44 PM »
Nice idea.  Do you have the Woodcraft part number?

Offline Greg Powers

  • Posts: 2283
  • Metric convert
    • Stargate Unofficiial
Re: Systainer dividers
« Reply #2 on: March 14, 2014, 08:14 PM »
Nice idea.  Do you have the Woodcraft part number?

For Sys III ---  158050 High Dividers

For Sys II ---- 158048 Low dividers
Greg Powers
Size:XL

Offline land_kel

  • Posts: 157
Re: Systainer dividers
« Reply #3 on: March 14, 2014, 11:09 PM »
So do I understand that I need 15 of these per Sys3 to make the setup shown in your post?
Lots of stuff

Offline Brice Burrell

  • Posts: 7363
  • Remodeling Contractor
    • The Green and Dark Blue blog
Re: Systainer dividers
« Reply #4 on: March 15, 2014, 08:45 AM »
So do I understand that I need 15 of these per Sys3 to make the setup shown in your post?

No, he is using eight in his set up and it looks like it's in a Sys 2.  Also, keep in mind these are $3 and $3.50 each piece, so Greg has $24 for the setup shown.  I think these aren't a bad deal, especially if you're like me and don't like making fiddly little projects like custom inserts.   
Check out my new blog, The Green and Dark Blue Blog.

Offline SRSemenza

  • Global Moderator
  • *
  • Posts: 8871
  • Finger Lakes Region, NY State , USA
Re: Systainer dividers
« Reply #5 on: March 15, 2014, 09:50 AM »
They work pretty well for set ups that don't require any exact spacing since you are limited to the increments on the dividers.  I have used then for several systainers. They can be cut if need be. They only stay in place by themselves if spanning the entire width / length with at least two parallel. However a few drops of super glue will hold them to the bottom in other situations.  The two heights can be used together.


102315-0




Seth

Offline Greg Powers

  • Posts: 2283
  • Metric convert
    • Stargate Unofficiial
Re: Systainer dividers
« Reply #6 on: March 15, 2014, 12:43 PM »
So do I understand that I need 15 of these per Sys3 to make the setup shown in your post?

No, only eight. But some trimming is required
Greg Powers
Size:XL

Offline Greg Powers

  • Posts: 2283
  • Metric convert
    • Stargate Unofficiial
Re: Systainer dividers
« Reply #7 on: March 15, 2014, 12:48 PM »
So do I understand that I need 15 of these per Sys3 to make the setup shown in your post?

No, he is using eight in his set up and it looks like it's in a Sys 2.  Also, keep in mind these are $3 and $3.50 each piece, so Greg has $24 for the setup shown.  I think these aren't a bad deal, especially if you're like me and don't like making fiddly little projects like custom inserts.  

I was lucky and got them on sale $2.65 and $2.25.  So the SYS II solution was 18 dollars.  
« Last Edit: March 15, 2014, 12:57 PM by GPowers »
Greg Powers
Size:XL

Offline wow

  • Inactive Member
  • *
  • Posts: 3579
  • Official WalMart greeter to the FOG
Re: Systainer dividers
« Reply #8 on: March 16, 2014, 03:37 AM »
Nice! Wish they had them in gray....
Trying to be one of the most helpful members on the FOG.

Offline Bhend18

  • Posts: 194
    • Hendricks Construction
Domino DF 500, CT 36 E, Boom Arm Set, CT MIDI, OF 1400, LR 32, FS 2424/2-LR 32, FS 1400/2 LR32, TS 55 REQ, TS 75 EQ, HKC 55 EB, FS 800, FS 1080, FS 1900, FS 3000, FSK 250, FSK 420, Parallel Guide Set, MFT/3, Kapex KS 120, Kapex UG, CXS, PDC 18/4, Drilling Dust Nozzle, CMS-GE, Carvex PS 420 EBQ, Pro 5 LTD,RO 90 DX, RO 150 FEQ, RTS 400 REQ, RS 2 E, LS 130 EQ, RAS 115 E, HL 850 E-F Plus, MX 1200 E EF, CT Wings, Vecturo OS 400, SysLite KAL-2, SYSRock

Offline Greg Powers

  • Posts: 2283
  • Metric convert
    • Stargate Unofficiial
Re: Systainer dividers
« Reply #10 on: March 16, 2014, 08:39 PM »
Also use these dividers for organizing 150 sandpaper in a Sys III.
Greg Powers
Size:XL

Offline fellaPC

  • Posts: 14
Re: Systainer dividers
« Reply #11 on: December 31, 2017, 07:29 PM »
wanted to dig this thread up... I see Woodcraft still has them in the dark gray color but any of you know where I can buy the light gray color... they appear to not be in stock on Amazon anymore. thanks

Offline Greg Powers

  • Posts: 2283
  • Metric convert
    • Stargate Unofficiial
Re: Systainer dividers
« Reply #12 on: January 20, 2018, 10:32 PM »
Does the color make a difference?
Greg Powers
Size:XL

Offline macrutt

  • Posts: 25

Offline presidentsdad

  • Posts: 21
Re: Systainer dividers
« Reply #14 on: January 23, 2019, 03:16 PM »
I think this what you afe looking for.
https://www.kofferfunshop.de/en/systainer/systainer-t-loc/systainer-trays-t-loc/compartment-divider-70x400mm-for-systainer-i.html

George

Also use these dividers for organizing 150 sandpaper in a Sys III.

Hey folks....I see the pic and the link, but when you order one, do you just get one divider or is it a pack of dividers like the picture above shows?  The link looks like it's just one of the dividers and not eight like the picture shows.  Assistance appreciated. :)
PresidentsDad - TS75; FS1900; CT36; RO150

Offline SRSemenza

  • Global Moderator
  • *
  • Posts: 8871
  • Finger Lakes Region, NY State , USA
Re: Systainer dividers
« Reply #15 on: January 23, 2019, 05:40 PM »
I think this what you afe looking for.
https://www.kofferfunshop.de/en/systainer/systainer-t-loc/systainer-trays-t-loc/compartment-divider-70x400mm-for-systainer-i.html

George

Also use these dividers for organizing 150 sandpaper in a Sys III.

Hey folks....I see the pic and the link, but when you order one, do you just get one divider or is it a pack of dividers like the picture above shows?  The link looks like it's just one of the dividers and not eight like the picture shows.  Assistance appreciated. :)

One divider. Those are sold by the piece.

Seth

Offline Billy stray

  • Posts: 317
Re: Systainer dividers
« Reply #16 on: January 25, 2019, 10:16 PM »
They work pretty well for set ups that don't require any exact spacing since you are limited to the increments on the dividers.  I have used then for several systainers. They can be cut if need be. They only stay in place by themselves if spanning the entire width / length with at least two parallel. However a few drops of super glue will hold them to the bottom in other situations.  The two heights can be used together.


(Attachment Link)




Seth

Just curious seth , I noticed whenever you post a systainer it's a classic, do you prefer them over Tlocs ?
Billy

Offline SRSemenza

  • Global Moderator
  • *
  • Posts: 8871
  • Finger Lakes Region, NY State , USA
Re: Systainer dividers
« Reply #17 on: January 25, 2019, 11:37 PM »
They work pretty well for set ups that don't require any exact spacing since you are limited to the increments on the dividers.  I have used then for several systainers. They can be cut if need be. They only stay in place by themselves if spanning the entire width / length with at least two parallel. However a few drops of super glue will hold them to the bottom in other situations.  The two heights can be used together.


(Attachment Link)




Seth

Just curious seth , I noticed whenever you post a systainer it's a classic, do you prefer them over Tlocs ?

Just happenstance. I did quite a few set ups before the T-Locs were available. T-Locs are more convenient. Occasionally something might work out better in a Classic  due to corner or sidewall shape. I have swapped some tools into T-Locs. Some  not, especially if I have the Systainer set up with dividers or custom inserts, or if it doesn't get stacked and latched very often.

Seth

Offline Coen

  • Posts: 445
Re: Systainer dividers
« Reply #18 on: January 28, 2019, 07:07 PM »
Latching a stack is so much easier with T-Loc, but if you carry a heavy stack, the top lid will warp way more with T-Loc.

But most of the hate for the (un)latching the classic systainers comes from people who don't understand that you need to just unclip the sides then slide the top systainer to the rear and have an easy time with the front clips.

Offline dlu

  • Posts: 161
Re: Systainer dividers
« Reply #19 on: January 28, 2019, 08:45 PM »
They are not on sale now :-(  $5 US for either side at Woodcraft these days...

Offline Greg Powers

  • Posts: 2283
  • Metric convert
    • Stargate Unofficiial
Re: Systainer dividers
« Reply #20 on: March 21, 2019, 12:28 AM »
They are not on sale now :-(  $5 US for either side at Woodcraft these days...

At the current price 3/2019 $5 each, they are a little expensive. Not sure I would use this approach at this price point.
Greg Powers
Size:XL

Offline Greg Powers

  • Posts: 2283
  • Metric convert
    • Stargate Unofficiial
Re: Systainer dividers
« Reply #21 on: March 21, 2019, 12:33 AM »
Just curious seth , I noticed whenever you post a systainer it's a classic, do you prefer them over Tlocs ?

It is an old post. The T-Loc was just released around the time I did this project. So the 90s are in a newer T-Lock and the 150s are in an older Systainer.
« Last Edit: March 21, 2019, 12:36 AM by Greg Powers »
Greg Powers
Size:XL