Author Topic: T-Loc boxes are great but...  (Read 3102 times)

0 Members and 1 Guest are viewing this topic.

Offline demographic

  • Posts: 291
T-Loc boxes are great but...
« on: April 02, 2017, 06:01 AM »
The handles wear on the ends and after a couple of years of site use the handles are in danger of coming off.
In pretty much every other way I love em but the handle pivots are a bit crap.
Just sayin.

Offline ginge

  • Posts: 11
Re: T-Loc boxes are great but...
« Reply #1 on: April 02, 2017, 09:01 AM »
I gotta agree with that. The handle wearing is the only criticism for them- I would say they last 3-5 years in my workflow.  Systainers are still one of my favourite festool products though!

Offline joiner1970

  • Posts: 3189
Re: T-Loc boxes are great but...
« Reply #2 on: April 02, 2017, 09:32 AM »
I've had a couple of handles come off too

Offline SRSemenza

  • Global Moderator
  • *
  • Posts: 7672
  • Finger Lakes Region, NY State , USA
Re: T-Loc boxes are great but...
« Reply #3 on: April 02, 2017, 10:06 AM »
Wow, well this is interesting and good to know. I better start looking for a fix.

Seth

Offline demographic

  • Posts: 291
Re: T-Loc boxes are great but...
« Reply #4 on: April 02, 2017, 05:16 PM »
On the plus points...
They fit into my Clarke toolsafe that I use for van security about as perfectly as its possible to get.
They're good to stack and move about on site with my extractor or my Sysroll.
I've got rid of pretty much all the other powered toolboxes and put the tools into T-Loc boxes.

Great boxes and I have a good few of them.
Crap handle pivots though.

Offline PaverMan

  • Posts: 7
Re: T-Loc boxes are great but...
« Reply #5 on: April 05, 2017, 07:42 AM »
I wish they were just A LITTLE bit thicker material so they wouldn't "rack" when they're sitting on an uneven surface and I wish they were glass-fiber reinforced ABS, instead of just plane ole ABS.

I like them, in general though.

Offline antss

  • Posts: 906
Re: T-Loc boxes are great but...
« Reply #6 on: April 05, 2017, 08:33 AM »
You fellas with the failing handles -

 did you experience the same thing with the first generation systainers ?

Offline demographic

  • Posts: 291
Re: T-Loc boxes are great but...
« Reply #7 on: June 17, 2017, 09:18 AM »
You fellas with the failing handles -

 did you experience the same thing with the first generation systainers ?

Dunno, I only started getting them after the move to T-Loc, personally I find the classics I've tried (had a look at other peoples Makita Classics) to be a faff to clip and unclip.

Offline ben_r_

  • Posts: 615
Re: T-Loc boxes are great but...
« Reply #8 on: June 19, 2017, 05:31 PM »
I wish they were just A LITTLE bit thicker material so they wouldn't "rack" when they're sitting on an uneven surface and I wish they were glass-fiber reinforced ABS, instead of just plane ole ABS.
Yea really.
If at first you don't succeed, redefine success!

Offline Corwin

  • Posts: 2395
Re: T-Loc boxes are great but...
« Reply #9 on: June 19, 2017, 07:50 PM »
You fellas with the failing handles -

 did you experience the same thing with the first generation systainers ?

The only Classic Systainers that I've had any issue with the latches are the small mini-Systainers. With these, the latches all to often twist sideways requiring a little attention. The rest of the Classic Systainers have had NO issues with the latches other than needing an occasional waxing -- never had one fall off.

The new T-Locs are easier to latch and unlatch, but are a real pain when stored in a SysPort. With the Classics, I could leave a Systainer closed, but unlatched and still close the drawer. But, if I close the drawer with a T-Loc Systainer the latch will pop off. Easy enough to put back on, but not so easy any more to bend down to pick it up off the floor.
Looks like your rabbit joint is a hare off! ;)

Offline Bob D.

  • Posts: 328
Re: T-Loc boxes are great but...
« Reply #10 on: June 19, 2017, 09:04 PM »
" But, if I close the drawer with a T-Loc Systainer the latch will pop off."

I think you've accidently discovered the heretofore untold method of removing the latch.

I'm making a hard copy of this thread before it's redacted. :)
-----
It's a table saw, do you know where your fingers are?