Author Topic: attaching breadboards  (Read 1262 times)

0 Members and 1 Guest are viewing this topic.

Offline clydeb

  • Posts: 3
attaching breadboards
« on: May 03, 2017, 09:18 AM »
Questions for the experts, I'm building a large conference table  4 ft wide in middle and two sections of 7ft,  total length 14 feet. Tapering to 40 inches on each end (Boat style)  Made from inch and half cherry.  The customers (law firm) asked if I would wrap the whole table in contrasting hard maple about 3/4 inch thick.  Question is how to attach the maple on the ends.  I though about using my domino cutter but thought about the whole wood movement senerio. With maple only 3/4 of an inch thick I dont think a tenon arrangement would work.  Maybe oversize pocket holes for pocket screws???? Any help would be appreciated  Thank You

Festool USA does not pre-approve the contents of this website nor endorse the application or use of any Festool product in any way other than in the manner described in the Festool Instruction Manual. To reduce the risk of serious injury and/or damage to your Festool product, always read, understand and follow all warnings and instructions in your Festool product's Instruction Manual. Although Festool strives for accuracy in the website material, the website may contain inaccuracies. Festool makes no representations about the accuracy, reliability, completeness or timeliness of the material on this website or about the results to be obtained from using the website. Festool and its affiliates cannot be responsible for improper postings or your reliance on the website's material. Your use of any material contained on this website is entirely at your own risk. The content contained on this site is provided for informational purposes only and does not constitute professional advice.


Offline justaguy

  • Posts: 97
Re: attaching breadboards
« Reply #1 on: May 03, 2017, 12:16 PM »
I have not tried it but there is this on YouTube

Offline RL

  • Posts: 3038
Re: attaching breadboards
« Reply #2 on: May 03, 2017, 12:24 PM »
I would use a 3/4" bearing guided rabbeting bit to route a tiny rebate and veneer it. Then use veneer to do the edge as well. You wouldn't have any wood movement problems but it would look like a 3/4" solid piece of maple.


Offline clydeb

  • Posts: 3
Re: attaching breadboards
« Reply #3 on: May 03, 2017, 08:24 PM »
Could you expound some on your idea please. Thanks

Offline richk

  • Posts: 46
Re: attaching breadboards
« Reply #4 on: May 03, 2017, 09:21 PM »
I used the @justaguy method above for a dining room table, about 38" wide, and which has shown some movement without developing any cracks or problems. It's been about 3 years and so far so good. Located in San Diego so no extremes of weather, but previously without breadboard ends it was a problem...

Offline Terry Fogarty

  • Posts: 390
Re: attaching breadboards
« Reply #5 on: May 03, 2017, 09:48 PM »
I've done countless breadboard table tops and always use the widest setting into all the top and middle end board and make my own tenons using the same species timber, then manually move the domino to achieve the wider mortises on the rest of the breadboard end.

I also glue the middle third of the breadboard to the table as minimal contraction/expansion will occur.
The one thing he didn't show was to give the end of the table and length of the breadboard a slight arris because their will be natural movement and if it's flush then a glueline will occur and it looks and feels terrible. 
.

Offline Dovetail65

  • Posts: 4502
    • Rose Farm Floor Medallions and Inlays
Re: attaching breadboards
« Reply #6 on: May 03, 2017, 10:06 PM »
Are we talking only a 3/4" wide border? Maybe I got it wrong. I dont really consider 3/4" a bread board, is it? It's more like a border.

IMHO if its truly only a 3/4" border of contrasting wood around the edge I would just glue it up that way from the start(1.5"x3/4" thick Maple glued to the 1.5" cherry), not attach it like a breadboard at all.

Now a 4" breadboard, that's a different animal.
« Last Edit: May 03, 2017, 10:12 PM by Dovetail65 »
The one who says it can't be done should avoid interrupting the person doing it.

Offline Untidy Shop

  • Posts: 2503
Re: attaching breadboards
« Reply #7 on: May 03, 2017, 11:22 PM »
These two links may assist -

The @thebicyclecafe  and my adaption of his method. He uses hand made dominos and a router, I used a D500 and Festool dominos.

thebicyclecafe -
http://festoolownersgroup.com/festool-how-to/loose-tenon-breadboard-ends-demonstration/

Reply #1

Untidy Shop -
http://festoolownersgroup.com/member-projects/my-magnificent-failure-(and-recovery)/msg281207/#msg281207

Reply #2
This is essentially the same method on the UTube video posted here by @justaguy .

Also note @Tezzer 's Reply #6 in this Thread.

_______________

If you are trimming and breadboarding, have a look at -

https://m.youtube.com/watch?feature=youtu.be&v=wVBEJF15Uxc

« Last Edit: May 03, 2017, 11:44 PM by Untidy Shop »
If you don't like Signatures, just go to Look and Layout and tick No Signatures.

“The test of the machine is the satisfaction it gives you. There isn't any other test. If the machine produces tranquility it's right. If it disturbs you it's wrong until either the machine or your mind is changed.”
― Robert M. Pirsig, Zen and the Art of Motorcycle Maintenance: An Inquiry Into Values