Woodworking & Power Tools Forum - Festool Owners Group > FESTOOL DISCUSSIONS > Festool How To... > Festool Addiction
Pages: [1]   Go Down
« previous next »
  Print  
Author Topic: Festool Addiction  (Read 1685 times)
0 Members and 1 Guest are viewing this topic.
Danny E

Offline Offline

Location: Los Angeles, USA
Member Since: Jan 2012
Posts: 54
« on: June 20, 2012, 03:25 AM »
Here you go! Got my domino 500 today for my garage cabinet project and more & more projects that are going to be on the way.

Now, for 19 mm melamine sheets, wht tenons to be used 5mm/6 mm. Any advise pls...
Logged
TS55, CT26, ETS 150/3, LR32 System, OF1400, Domino 500, MFT3, D36, 1400 Holy Rail x2, Parallel Guides, MFK700 Set, Clamps
Festool USA does not pre-approve the contents of this website nor endorse the application or use of any Festool product in any way other than in the manner described in the Festool Instruction Manual. To reduce the risk of serious injury and/or damage to your Festool product, always read, understand and follow all warnings and instructions in your Festool product's Instruction Manual. Although Festool strives for accuracy in the website material, the website may contain inaccuracies. Festool makes no representations about the accuracy, reliability, completeness or timeliness of the material on this website or about the results to be obtained from using the website. Festool and its affiliates cannot be responsible for improper postings or your reliance on the website's material. Your use of any material contained on this website is entirely at your own risk. The content contained on this site is provided for informational purposes only and does not constitute professional advice.

Kev

Offline Offline

Location: Australia
Member Since: Nov 2011
Posts: 2426
« Reply #1 on: June 20, 2012, 03:31 AM »
Quote from: Danny E on June 20, 2012, 03:25 AM
Here you go! Got my domino 500 today for my garage cabinet project and more & more projects that are going to be on the way.

Now, for 19 mm melamine sheets, wht tenons to be used 5mm/6 mm. Any advise pls...



6mm meets the "one third" guideline ...

Congrats on your new toy tool  Smile
Logged
Timtool
Retailer

Online Online

Location: Belgium
Member Since: Mar 2011
Posts: 717



WWW
« Reply #2 on: June 20, 2012, 06:34 AM »
Quote from: Kev on June 20, 2012, 03:31 AM


6mm meets the "one third" guideline ...

Congrats on your new toy tool  Smile
Yes, but i think that goes when the woods are of equal strength, it's been discussed before and some, including me, prefer the 5mm ones because those 5mm of beech are allot stronger than the remaining 14mm of chipboard. The panel will split or break less fast if it has a bit more material around the tenon!
Logged
TS55R, CT22E, CTLmini, Kapex KS120, ETS125, ETS150/5, RO150, RO90, CXS-set, T-15+3 set, DTS400, OF1010, OF2200 set, Carvex PS420 EBQ set, Centrotec installer set, LR32-sys, FS-800, FS-LR-1400x2, domino 500+domino sys, domino 700 XL, Surfix-sys, Sys-box 1, Syslite, LEV-350, Sys-box,MFTB/1-2-4... MFTC
Brice Burrell

Offline Offline

Location: Pittsburgh, PA, USA
Member Since: Mar 2007
Posts: 6186


Remodeling Contractor


WWW
« Reply #3 on: June 20, 2012, 07:52 AM »
Quote from: Timtool on June 20, 2012, 06:34 AM
Quote from: Kev on June 20, 2012, 03:31 AM


6mm meets the "one third" guideline ...

Congrats on your new toy tool  Smile
Yes, but i think that goes when the woods are of equal strength, it's been discussed before and some, including me, prefer the 5mm ones because those 5mm of beech are allot stronger than the remaining 14mm of chipboard. The panel will split or break less fast if it has a bit more material around the tenon!

I completely agree.  Another advantage is the length of the 5mm tenons.  At 30mm you get 15mm in each, you aren't going to accidentally plunge all the way through 18 or 19mm material when mortising in the face.  If you use the 6mm tenons you'll have to remember to offset the mortises. 
Logged
Check out my new blog, The Green and Dark Blue Blog.
davee

Offline Offline

Location: Central Illinois
Member Since: Jan 2010
Posts: 266
« Reply #4 on: June 20, 2012, 08:03 AM »
I also agree with the 5mm for stregth, and also Brice's comment about 15mm plunge depth is right on.  It only required a few missed depth settings to make me look at each setting closely before plunging.  It also makes interesting patterns in your work bench or MFT.
Logged
ScotF

Online Online

Location: Southern Orange County, CA, USA
Member Since: Jul 2009
Posts: 1349


WWW
« Reply #5 on: June 20, 2012, 10:23 AM »
I also agree with 5mm and I think that this is one of the reasons Festool provides the 500 with a 5mm cutter -- one of the most useful sizes for 19mm sheet goods.

Scot
Logged
Kev

Offline Offline

Location: Australia
Member Since: Nov 2011
Posts: 2426
« Reply #6 on: June 20, 2012, 12:02 PM »
Quote from: Kev on June 20, 2012, 03:31 AM
Quote from: Danny E on June 20, 2012, 03:25 AM
Here you go! Got my domino 500 today for my garage cabinet project and more & more projects that are going to be on the way.

Now, for 19 mm melamine sheets, wht tenons to be used 5mm/6 mm. Any advise pls...



6mm meets the "one third" guideline ...

Congrats on your new toy tool  Smile

... or 5mm  Embarassed
Logged
Pages: [1]   Go Up
  Print  
« previous next »
 
Jump to: