Pages: [1] 2  All   Go Down
  Print  
Author Topic: making built-ins part 3,4,5,6a ,6b, 7,8 and NOW # 9 ITS GREAT !  (Read 15815 times)
0 Members and 1 Guest are viewing this topic.
honeydokreg

Offline Offline

Location: Woodstock GA
Member Since: Feb 2007
Posts: 1598



WWW
« on: January 21, 2011, 01:17 AM »

well just finished # 3  this one is on fluting !  enjoy


Making Built-Ins 3



Part 4:

Making Custom Built-ins 4


Part 5:  my customers house set up

Making Built-Ins Part 5 My Portable shop set up



Part 6a  is now up (had to make it part a and b as 10 minutes is limit on you tube

making built-ins part 6a



Part 6b is up and running
Making Custom Built-Ins by Kreg Kreg's custom Carpentry Part


part 7 arches

Making Custom Built-Ins by Kreg Part 7 Making Arch


Part 8 Inside the house

Making Custom Built-Ins by Kreg Kreg's Custom Carpentry Par



Part 9... you will all love this shows cab uppers all finished and a special part at the end... # 10 will be on face frames and doors but will be in about 1 week

Making Built-ins part 9 almost done

« Last Edit: January 30, 2011, 12:49 AM by honeydokreg » Logged

pay attention to the details.... they make the difference... festool does
www.kregscustomcarpentry.com
youtube channel:  builtinsbykreg
Festool USA does not pre-approve the contents of this website nor endorse the application or use of any Festool product in any way other than in the manner described in the Festool Instruction Manual. To reduce the risk of serious injury and/or damage to your Festool product, always read, understand and follow all warnings and instructions in your Festool product's Instruction Manual. Although Festool strives for accuracy in the website material, the website may contain inaccuracies. Festool makes no representations about the accuracy, reliability, completeness or timeliness of the material on this website or about the results to be obtained from using the website. Festool and its affiliates cannot be responsible for improper postings or your reliance on the website's material. Your use of any material contained on this website is entirely at your own risk. The content contained on this site is provided for informational purposes only and does not constitute professional advice.

Steve-CO

Offline Offline

Location: Littleton, CO
Member Since: Oct 2007
Posts: 786


« Reply #1 on: January 21, 2011, 01:58 AM »

 Thumbs Up  Very nice, great videos, thanks again for doing these.   Thumbs Up
Logged
erock

Offline Offline

Location: cleveland, ohio
Member Since: Apr 2010
Posts: 782



« Reply #2 on: January 21, 2011, 07:44 AM »

Nice video!  Who makes the green tape?  It looks like it sticks good to the paint with out peeling it off.  I could use some tape like that with some projects.
Keep up the good work, both with the tools and the vids! Big Grin
Eric
Logged

Kapex with  UG set,  Domino, HL 850, OF1400, MFK700,  TS 55, PS 300, CXS, C15, MFT 800, MFT1080,  MFT/3, CT 26, CT midi, LS130, DX93 ,  DTS 400, RO 125,  ETS 125, LR32 set, parallel guide set, FS 1400/2-LR32, FR 2424/2-LR32,  FS 3000/2,  (2) FS 1400/2,  FS 800/2, Syslite,
BobKovacs

Offline Offline

Location: UNITED STATES (US)
Member Since: Nov 2007
Posts: 299


« Reply #3 on: January 21, 2011, 07:57 AM »

Nice video!  Who makes the green tape?  It looks like it sticks good to the paint with out peeling it off.  I could use some tape like that with some projects.

Looks like Frog Tape, which is carried at Lowes, but not at Home Depot.  HD had some kind of issue with 3M getting mad at them for carrying both products.
Logged
honeydokreg

Offline Offline

Location: Woodstock GA
Member Since: Feb 2007
Posts: 1598



WWW
« Reply #4 on: January 21, 2011, 08:05 AM »

Yep frog tape is it! 
Logged

pay attention to the details.... they make the difference... festool does
www.kregscustomcarpentry.com
youtube channel:  builtinsbykreg
GhostFist

Offline Offline

Location: Canada
Member Since: Oct 2010
Posts: 1250



« Reply #5 on: January 21, 2011, 08:50 AM »

keep rockin Kreg!
Logged
rookie08

Offline Offline

Location: Maryland
Member Since: Dec 2007
Posts: 198


« Reply #6 on: January 21, 2011, 09:58 AM »

Cup of coffee and a video by Kreg; what a great way to start my morning!   Big Grin

Nicely done!

Cheers
Logged
Wonderwino

Offline Offline

Location: American Bison Country
Member Since: Apr 2008
Posts: 665



« Reply #7 on: January 21, 2011, 10:33 AM »

Great series, Kreg!  Keep them coming!   Big Grin
Logged

Water separates the people of the world; wine unites them.
mikeneron

Offline Offline

Location: Winnipeg, Manitoba, Canada
Member Since: Apr 2009
Posts: 206


« Reply #8 on: January 21, 2011, 02:43 PM »

Have enjoyed watching your videos so far, keep up the good work.  In part 3 your glasses were doing a good job of protecting your hair  Tongue Out
Logged
honeydokreg

Offline Offline

Location: Woodstock GA
Member Since: Feb 2007
Posts: 1598



WWW
« Reply #9 on: January 22, 2011, 07:48 AM »

I just went in and added speech bubbles to all videos on the importance of wearing hearing and eye protection.  and I agree, and I usually always wear safety glasses, in this case I was thinking about what I was doing and going to say!

Logged

pay attention to the details.... they make the difference... festool does
www.kregscustomcarpentry.com
youtube channel:  builtinsbykreg
BigHonu

Offline Offline

Location: Hawaii, USA
Member Since: Oct 2010
Posts: 145


« Reply #10 on: January 22, 2011, 04:09 PM »

Keep the videos coming!  My wife watched the last one with me and said, "he looks like a fun guy!"


Sent from my iPhone using Tapatalk
Logged
Peter Halle
Global Moderator

Offline Offline

Location: Powhatan, Virginia USA
Member Since: Jul 2007
Posts: 7618


How Can You Disagree with HIM?


WWW
« Reply #11 on: January 22, 2011, 05:22 PM »

Keep the videos coming!  My wife watched the last one with me and said, "he looks like a fun guy!"


Sent from my iPhone using Tapatalk

Spend two days in a class with him and....  yes he is a fun guy.
Logged

The tools in my truck were talking the other day.  The Dewalts, PC's, Boschs, Makitas were not happy.  They also were in the minority.  Their complaint:  They felt unused and unappreciated since the Festools moved in.  I guess the truth hurts.
Dan Rush

Offline Offline

Location: Chicago, Il. USA
Member Since: Feb 2008
Posts: 553


Trim carpenter


« Reply #12 on: January 22, 2011, 06:41 PM »

Kreg,
I'm liking the video series.  One thought on #3:  When the fence is set up for the outside flute, I just shoot down the opposite side of the board to complete both outside flutes, then adjust for the center run.  One less adjustment (saves time) and one less chance for a goof.

Dan
Logged
WarnerConstCo.

Offline Offline

Location: Auburn, In usa
Member Since: Apr 2008
Posts: 3225



WWW
« Reply #13 on: January 22, 2011, 07:42 PM »

I did the lights in the last two just about like that., with the same dimmalbe set up.

I did take them apart though so the covers just screwed into the plywood.
Logged

Kodi Crescent

Offline Offline

Location: USA
Member Since: Aug 2010
Posts: 460


« Reply #14 on: January 22, 2011, 10:46 PM »

Kreg - I'm glad you added safety glasses.  I don't do anything without them any longer.

One of the worst eye injuries I sustained was when trying to light a pilot light on a water heater.  I had opened the garage or something, and a gust of wind came up as I was lighting the pilot.  The gust of wind blew through the heater vent, and blew a tiny piece of rust or metal into my eye.  It became very difficult to see, and I had to go to the eye doctor to have it removed.  But that wasn't the worst part.  I had to go back to the eye doctor almost every day for at least two weeks so they could look at the tiny scar the metal produced, and try to pick out any remaining pieces, rust particles, etc.  Going to the eye doctor so frequently was such a hassle that I never want to experience it again.  I wear safety glasses for ANYTHING I do in the garage.

A question about the built ins - When you cut the parts, how square is square enough?
Logged
WarnerConstCo.

Offline Offline

Location: Auburn, In usa
Member Since: Apr 2008
Posts: 3225



WWW
« Reply #15 on: January 22, 2011, 11:19 PM »

The only two times I got steel in my eyes I was wearing safety glasses and a face shield.

I am only counting the times I had to have it drilled out.
Logged

Dovetail65

Offline Offline

Location: UNITED STATES (US)
Member Since: Feb 2008
Posts: 3865



« Reply #16 on: January 23, 2011, 12:03 AM »

Why are these posts all over the place and not in the same thread?

It's already tough to see them in order, in a year it really will be.  Smiley

At the very least link to the 1 @ 2 vids and back link as you go along, though that's still not as nice.;

I do think you may have added 4 here, maybe you can throw in 1 and 2?
« Last Edit: January 23, 2011, 12:05 AM by Dovetail65 » Logged

The one who says it can't be done should avoid interrupting the person doing it.
ScotF

Offline Offline

Location: Southern Orange County, CA, USA
Member Since: Jul 2009
Posts: 1810


« Reply #17 on: January 23, 2011, 01:45 AM »

Keep up the videos, Kreg.  They are very well done and it looks like you are having fun with them.

Scot
Logged
Robert

Offline Offline

Location: Southeast Ga. USA
Member Since: Nov 2010
Posts: 23


« Reply #18 on: January 23, 2011, 09:36 PM »

Great show! As an aspiring cabinet maker "for my garage" theyare great.
Logged
Steve Rowe

Offline Offline

Location: Russellville, AR
Member Since: Jan 2007
Posts: 467


« Reply #19 on: January 23, 2011, 09:54 PM »

I am really enjoying this series, keep it going.  It is also cool that you have a tool named after you Grin.
Logged
honeydokreg

Offline Offline

Location: Woodstock GA
Member Since: Feb 2007
Posts: 1598



WWW
« Reply #20 on: January 24, 2011, 11:23 PM »

well I just added part 5 it is at the start of this thread.  it shows my set up at the customers house and really shows the value that festools adds to carpenters job sites !
Logged

pay attention to the details.... they make the difference... festool does
www.kregscustomcarpentry.com
youtube channel:  builtinsbykreg
Wood_Junkie

Offline Offline

Location: Madison, Wisconsin - USA
Member Since: Dec 2009
Posts: 1313



« Reply #21 on: January 24, 2011, 11:28 PM »

Great, fun series Kreg!

I really like your red, white & blue Systainer, laying front and center.  Too bad that chump stepped in front of it and started blabbing!   Wink

Whoever was on your camera for 3 & 4 did a great job.  Good framing, zooms in for details.  Really all around excellent walk-throughs.
« Last Edit: January 24, 2011, 11:32 PM by Wood_Junkie » Logged
honeydokreg

Offline Offline

Location: Woodstock GA
Member Since: Feb 2007
Posts: 1598



WWW
« Reply #22 on: January 24, 2011, 11:37 PM »

Thanks. Lol. Got the tanos systainer custom at the iwf show last august. Probably the one and only!  Yep that was good video. I have an editing program still trying to figure it out.
Logged

pay attention to the details.... they make the difference... festool does
www.kregscustomcarpentry.com
youtube channel:  builtinsbykreg
truck90278

Offline Offline

Location: Redondo Beach, CA
Member Since: May 2010
Posts: 69


« Reply #23 on: January 26, 2011, 01:31 AM »

Kreg, being a novice, your videos are extremely helpful.  I was concerned that when using my Domino, I was having to tap the dominos in with a plastic hammer, evidentily that is the way they are supposed to be.  thanks again
Ralph
Logged

CT22, CT26, TS55, MFT3, Domino 500, DTS 400, RO 125, RO 90, ETS 125, OF1010, CXS, Boom arm, Trion, parallel guides, LR32 system, shop cleaning set
John Bates
Retailer

Online Online

Location: UK
Member Since: Dec 2010
Posts: 117



« Reply #24 on: January 26, 2011, 04:40 AM »

Good to see the tips in action, you've had plenty of practice and make it look easy, I bet the outakes would be more my style!!
Logged

Manufacturer's agent. In my spare time, I produce expensive sawdust, chippings, off cuts and kindling to a very high standard.
GhostFist

Offline Offline

Location: Canada
Member Since: Oct 2010
Posts: 1250



« Reply #25 on: January 26, 2011, 09:06 AM »

Kreg i'd by you a beer just for the Clint ringtone. On a side note from your awesome vids, I just got "The Man With No Name Series" on Blu-ray and it's fricken fan fricken tastic. Highly recommended "fist Full Of Dollars, A Few Dollars more, The Good The Bad And The Ugly" haven't looked and sounded this good since their original release!

Back on topic I like your use of both the domino and the pocket holes for assembly. Fast and strong. the best of classic joinery reinforced with pocket holes. Thumbs up.

Oh ya tell me you'll make more of these, I'm hoping this isn't over.
Logged
honeydokreg

Offline Offline

Location: Woodstock GA
Member Since: Feb 2007
Posts: 1598



WWW
« Reply #26 on: January 26, 2011, 09:49 AM »

Hanks for the compliments!  Yep that was funny when my phone rang and it was right by the camera!  So I left in in !

Videos are not over I am taking it all the to the finish ! And the last video will be me cashing the check and heading to highland hardware and buying more festools !  Almost have every one they make then they come out with more!!!
Logged

pay attention to the details.... they make the difference... festool does
www.kregscustomcarpentry.com
youtube channel:  builtinsbykreg
pdlandgang

Offline Offline

Location: UNITED STATES (US)
Member Since: Feb 2010
Posts: 41


« Reply #27 on: January 26, 2011, 10:12 AM »

I was wondering when the home DVD box set would be coming out?  and does it come with a SYS2 or SYS3 carrying case?
Logged
RL

Offline Offline

Location: Canada
Member Since: Feb 2010
Posts: 2447



« Reply #28 on: January 26, 2011, 10:17 AM »

I am really enjoying the video series. Thanks!

Coincidentally, I have thew same Ennio Morricone ringtone on my phone, and it rang just as I was about to start a ski run last week. We were videoing it at the time, which made it appear really cool!
Logged

I like green.
Shane Holland
Festool USA Employee
FOG Administrator

Offline Offline

Location: USA
Member Since: Jan 2007
Posts: 6476



WWW
« Reply #29 on: January 26, 2011, 10:35 AM »

Quote
Part 6a  is now up (had to make it part a and b as 10 minutes is limit on you tube

Kreg, thanks for sharing these. Needless to say, everyone's enjoying them. Just wanted to make a note that YouTube extended the limit to 15 minutes about 6 months ago to save you the effort of splitting videos.
Logged

Shane Holland | Festool USA | Sales: 888-337-8600 | Service: 800-554-8741 | TS 55 REQ Recall Hotline: 855-784-9727| sho@festoolusa.com



Power Tools, Domino Joiners, RRP HEPA Vacs, Track SawsDrywall Sanders, Cordless Drills, Tools for Painters, Jigsaws, Router Tables
Pages: [1] 2  All   Go Up
  Print  
 
Jump to: