Author Topic: Shopsmith connection  (Read 3566 times)

0 Members and 1 Guest are viewing this topic.

Offline DGreen

  • Posts: 1
Shopsmith connection
« on: May 04, 2017, 07:33 PM »
HI
Newbie here. I purchased a CT36-E and want to connect it to the dust port of a Shopsmith Band saw.  What adapter do I need to connect the supplied hose to a 2 1/4" dust port?  Or do I need a different hose?

Don G

Festool USA does not pre-approve the contents of this website nor endorse the application or use of any Festool product in any way other than in the manner described in the Festool Instruction Manual. To reduce the risk of serious injury and/or damage to your Festool product, always read, understand and follow all warnings and instructions in your Festool product's Instruction Manual. Although Festool strives for accuracy in the website material, the website may contain inaccuracies. Festool makes no representations about the accuracy, reliability, completeness or timeliness of the material on this website or about the results to be obtained from using the website. Festool and its affiliates cannot be responsible for improper postings or your reliance on the website's material. Your use of any material contained on this website is entirely at your own risk. The content contained on this site is provided for informational purposes only and does not constitute professional advice.


Offline Birdhunter

  • Posts: 1993
  • Woodworker, Sportsman, Retired
Re: Shopsmith connection
« Reply #1 on: May 04, 2017, 08:51 PM »
Can't directly answer your question, but both Woodcraft and Rockler have lots of adaptors. I'd recommend browsing them to find something to fit.
Birdhunter

Offline jobsworth

  • Posts: 4573
  • Burger Babe Says: I Even Buy Green Bananas
Re: Shopsmith connection
« Reply #2 on: May 14, 2017, 03:01 AM »
I'm sure you can rig something up. I've rigged up a 4" connection for mine before.

As bird hunter said lots of adapters out there.
Loving the Calif sun....

Offline Tinker

  • Posts: 3556
Re: Shopsmith connection
« Reply #3 on: May 14, 2017, 04:12 AM »
When I need a quick fix I go a plumbing supply, or big box and look thru the Fernco connectors.
Tinker
Wayne H. Tinker

Offline Bob D.

  • Posts: 716
Re: Shopsmith connection
« Reply #4 on: May 14, 2017, 05:31 AM »
This link will give you an idea of the variety available.

http://www.homedepot.com/b/Plumbing-Pipes-Fittings/Fernco/N-5yc1vZbqpfZ4hs
-----
It's a table saw, do you know where your fingers are?

Offline Claimdude

  • Posts: 308
Re: Shopsmith connection
« Reply #5 on: May 14, 2017, 08:56 AM »
Don,
I can check the fittings after church today so let me know if you don't get an answer. I have SS and Festool vac. My SS is hooked up to a Jet 1 1/2 hp dust collector though.

Jack

Offline bigmoguls

  • Posts: 15
Re: Shopsmith connection
« Reply #6 on: August 16, 2017, 10:15 PM »
Go to Home Depot, buy the 2 1/2" hose kit for their shop vacs (about $25).  It fits the Shopsmith table saw dust extraction port perfectly, you just need to make sure it fits the CT36 intake port.   

http://www.homedepot.com/p/RIDGID-2-1-2-in-x-20-ft-Tug-A-Long-Vacuum-Hose-for-RIDGID-Wet-Dry-Vacs-VT2522/203235220

Offline QuailRider43

  • Posts: 81
Re: Shopsmith connection
« Reply #7 on: August 17, 2017, 12:20 AM »