Author Topic: Bevel cuts  (Read 2300 times)

0 Members and 1 Guest are viewing this topic.

Offline jjowen

  • Posts: 123
Bevel cuts
« on: December 09, 2018, 08:32 PM »


If you do something that you did not intend to do, but decide that it was a good idea anyway, is it still considered to be a mistake?
Disclaimer: All posts after 12:00pm on Fridays (GMT+10) should be independently verified for relevance and veracity.

Festool USA does not pre-approve the contents of this website nor endorse the application or use of any Festool product in any way other than in the manner described in the Festool Instruction Manual. To reduce the risk of serious injury and/or damage to your Festool product, always read, understand and follow all warnings and instructions in your Festool product's Instruction Manual. Although Festool strives for accuracy in the website material, the website may contain inaccuracies. Festool makes no representations about the accuracy, reliability, completeness or timeliness of the material on this website or about the results to be obtained from using the website. Festool and its affiliates cannot be responsible for improper postings or your reliance on the website's material. Your use of any material contained on this website is entirely at your own risk. The content contained on this site is provided for informational purposes only and does not constitute professional advice.


Offline Birdhunter

  • Posts: 2481
  • Woodworker, Sportsman, Retired
Re: Bevel cuts
« Reply #1 on: December 09, 2018, 08:49 PM »
Some ( maybe most ) of my best woodturnings and boxes have sprung from mistakes. Some have been retrieved from my shop waste bin and reworked into something previously unthought of. I think of mistakes as a spur to try something new. Some end up in the city dump and some as someones’s treasure.
Birdhunter

Offline Peter_C

  • Posts: 752
Re: Bevel cuts
« Reply #2 on: December 10, 2018, 12:20 AM »
The fence looks like mine *shrugs*

Offline Corwin

  • Posts: 2644
Re: Bevel cuts
« Reply #3 on: December 10, 2018, 03:20 AM »
A Zero-clearance fence. Sweet!  [wink]

Offline jarbroen

  • Posts: 119
Re: Bevel cuts
« Reply #4 on: December 10, 2018, 01:54 PM »
And the fence is aluminum so you didn't mess up your blade at least :D

Offline Vondawg

  • Posts: 263
Re: Bevel cuts
« Reply #5 on: December 10, 2018, 02:15 PM »
The new down under fence !
There are no mistakes....just new designs.

Offline RKA

  • Posts: 1522
Re: Bevel cuts
« Reply #6 on: December 10, 2018, 03:18 PM »
As long as you tell no one, it's not a mistake, it was a design choice.   [smile]
-Raj

Offline Peter Halle

  • Global Moderator
  • *
  • Posts: 11847
Re: Bevel cuts
« Reply #7 on: December 10, 2018, 05:23 PM »
Lots of those around.   Now have fun on your MFT! You got your first scratch so to speak.

Peter

Offline DeformedTree

  • Posts: 442
Re: Bevel cuts
« Reply #8 on: December 10, 2018, 09:27 PM »
you coped your miter fence so it fits better into corners.  You enhanced it.

Offline infer

  • Posts: 36
Re: Bevel cuts
« Reply #9 on: December 11, 2018, 03:10 AM »
Hush now... Festool will charge 350 for the upgraded miter fence if they find out.

Offline Mario Turcot

  • Posts: 828
Re: Bevel cuts
« Reply #10 on: December 11, 2018, 09:56 AM »
If you keep going it might fit in a systainer  [eek]
Mario

Offline ChuckM

  • Posts: 921
Re: Bevel cuts
« Reply #11 on: December 11, 2018, 10:07 AM »
On the bright side of it, you can now use the fence as an angle gauge to set your saw's angle if you need to repeat the same bevel cut....  ;D

Offline Farming_Sawyer

  • Posts: 125
  • Sawyer, builder, winemaker, farmer, chef
    • Foley's Custom Sawmill
Re: Bevel cuts
« Reply #12 on: December 11, 2018, 12:59 PM »
As a Sawyer I always saw there are two types of Sawyer.... Those who have sawn into their mill and those who are gonna.... Those who say they never have never will are either lying or not trying, ie, pushing the limits and mincing trees into as much lumber as possible.
CT 26E, RO125, sys-mft, sys-toolbox, a bunch of 30 year old tools I'm looking to replace.

Offline gunnyr

  • Posts: 168
    • https://www.instagram.com/compassfinecarpentry/
Re: Bevel cuts
« Reply #13 on: December 11, 2018, 05:51 PM »
Looks exactly like my fence, perfect!   [embarassed] [cool]

What’s the point of having tools is you don’t USE them?
Semper Fi,
Jeff

TS 55 REQ|HKC 55|PSB 420|DF 500|PRO 5 LTD|ETS 150/3|DTSC 400|RO 90|RO 150|OF 1400|MFK 700|LR 32|MFS 400/700|CXS (2)|PDC 18|DWC 18-4500|CT MIDI|CT 26|CT 48|MFT/3 (2)|VAC SYS-SET|DUO-SET|SYSLITE KAL II
US Marines - UK Wildcats - Cincinnati Reds

Online SoonerFan

  • Posts: 435
Re: Bevel cuts
« Reply #14 on: December 12, 2018, 10:07 PM »
Can’t tell you how many times I have almost cut into my MFT/3 like that.  To date I have been able to catch myself at the last minute.  I know it will happen at some point.  I did however recently have a router slip and ding the scale on my Woodpeckers MFS......