Julian Tracy
 Offline
Location: Redford, MI Member Since: Oct 2007
Posts: 427
|
 |
« on: March 29, 2011, 02:18 PM » |
|
http://www.tooldepot247.com/proddetail.asp?prod=921086AA13* Much shallower depth than the Festool and half the price. Most Fein accessories I've seen are upto and sometimes exceed the quality of Festool stuff. Might be a better bet than the Festool version - I like that it doesn't stick out as far. JT
|
|
|
|
|
Logged
|
|
|
|
Festool USA does not pre-approve the contents of this website nor endorse the application or use of any Festool product in any way other than in the manner described in the Festool Instruction Manual. To reduce the risk of serious injury and/or damage to your Festool product, always read, understand and follow all warnings and instructions in your Festool product's Instruction Manual. Although Festool strives for accuracy in the website material, the website may contain inaccuracies. Festool makes no representations about the accuracy, reliability, completeness or timeliness of the material on this website or about the results to be obtained from using the website. Festool and its affiliates cannot be responsible for improper postings or your reliance on the website's material. Your use of any material contained on this website is entirely at your own risk. The content contained on this site is provided for informational purposes only and does not constitute professional advice.
|
|
Brice Burrell
Offline
Location: Pittsburgh, PA, USA Member Since: Mar 2007
Posts: 6216
Remodeling Contractor
|
|
« Reply #1 on: March 29, 2011, 02:25 PM » |
|
Nice.  You got a bad link. |
|
|
|
|
Logged
|
|
|
|
Jeff Hein
Offline
Location: Rockford, MI Member Since: Nov 2010
Posts: 119
|
|
« Reply #2 on: March 29, 2011, 02:50 PM » |
|
|
|
|
|
|
Logged
|
|
|
|
|
|
leakyroof
Offline
Location: USA Member Since: Mar 2011
Posts: 320
|
|
« Reply #4 on: March 29, 2011, 03:26 PM » |
|
Don't forget that good DC doesn't like sharp turns and small radius fittings. Haven't looked at the inside of the Festool Y fitting, but it may be stick out from the vacuum farther for a good reason.  |
|
|
|
|
Logged
|
|
|
|
harry_mc
Offline
Location: North Richland Hills, TX, USA Member Since: Nov 2008
Posts: 63
|
|
« Reply #5 on: March 29, 2011, 04:58 PM » |
|
Is the Fein adapter anti-static?
|
|
|
|
|
Logged
|
|
|
|
Brice Burrell
Offline
Location: Pittsburgh, PA, USA Member Since: Mar 2007
Posts: 6216
Remodeling Contractor
|
|
« Reply #6 on: March 29, 2011, 05:26 PM » |
|
Is the Fein adapter anti-static?
I'd guess no. |
|
|
|
|
Logged
|
|
|
|
MarkF
Offline
Location: Concord, NC Member Since: Jan 2007
Posts: 272
Concord, NC
|
|
« Reply #7 on: March 29, 2011, 06:05 PM » |
|
Is the Fein adapter anti-static?
I'm not trying to be a smart a@# ...but why would that matter? It's located at the end of the hose. I use a Fein Turbo II with a stock gray PVC hose and have this Y adapter attached with no static issues. Is this a Festool issue? |
|
|
|
|
Logged
|
|
|
|
PeterK
Offline
Location: Wet muggy humid South Member Since: Jan 2007
Posts: 815
|
|
« Reply #8 on: March 29, 2011, 06:22 PM » |
|
I guess it depends upon where you live. Here in Louisiana, I have used my CT22 with both regular and anti-static hoses and fittings and have never been shocked or had any type of issue. Maybe in arid Arizona or some such place it is a major problem.
|
|
|
|
|
Logged
|
|
|
|
Brice Burrell
Offline
Location: Pittsburgh, PA, USA Member Since: Mar 2007
Posts: 6216
Remodeling Contractor
|
|
« Reply #9 on: March 29, 2011, 08:19 PM » |
|
Is the Fein adapter anti-static?
I'm not trying to be a smart a@# ...but why would that matter? It's located at the end of the hose. I use a Fein Turbo II with a stock gray PVC hose and have this Y adapter attached with no static issues. Is this a Festool issue? As Peter said you might have a problem in you lived in desert or, if are like me and cut a lot PVC (Azek) the anti-static feature makes a big difference. |
|
|
|
|
Logged
|
|
|
|
mishle
Offline
Location: Austin,TX Member Since: Jan 2009
Posts: 122
|
|
« Reply #10 on: March 29, 2011, 11:14 PM » |
|
Living in Colorado when I tried using a non-anti-static hose it felt like holding on to an electric fence for cattle.
|
|
|
|
|
Logged
|
|
|
|
harry_mc
Offline
Location: North Richland Hills, TX, USA Member Since: Nov 2008
Posts: 63
|
|
« Reply #11 on: March 29, 2011, 11:32 PM » |
|
Is the Fein adapter anti-static?
I'm not trying to be a smart a@# ...but why would that matter? It's located at the end of the hose. I use a Fein Turbo II with a stock gray PVC hose and have this Y adapter attached with no static issues. Is this a Festool issue? Even here in Texas in the winter it gets dry enough in most buildings that static can become an issue (probably not an issue outside). I've only used the adapter at the beginning of the hose (right out of the extractor), not the end. If you aren't using an anti-static hose it won't make a difference. I only asked because if static is an important issue to someone, they should know that comparing the two adapters is an apples to oranges comparison. -Harry |
|
|
|
|
Logged
|
|
|
|
MarkF
Offline
Location: Concord, NC Member Since: Jan 2007
Posts: 272
Concord, NC
|
|
« Reply #12 on: March 30, 2011, 10:00 AM » |
|
You guys are missing my question. I'll rephrase it: Would having a regular (ie:not anti-static) "Y" adapter significatly impact the performance of an anti-static hose? Apologies for the confusion!
I've always wondered why Festool offers a solution and nothing antistatic is offered from Fein. They are similar machines so you would think static is just as big an issue with Fein. It probably is and I'm just "blessed" (not) with humidity.
|
|
|
|
|
Logged
|
|
|
|
SRSemenza
Global Moderator
 Online
Location: UNITED STATES (US) Member Since: Jun 2007
Posts: 4027
Finger Lakes Region, NY State , USA
|
|
« Reply #13 on: March 30, 2011, 10:25 AM » |
|
You guys are missing my question. I'll rephrase it: Would having a regular (ie:not anti-static) "Y" adapter significatly impact the performance of an anti-static hose? Apologies for the confusion!
I've always wondered why Festool offers a solution and nothing antistatic is offered from Fein. They are similar machines so you would think static is just as big an issue with Fein. It probably is and I'm just "blessed" (not) with humidity.
Yes, the non-antistatic adapter will in effect make the hose non-antistatic. Because it breaks the connection to the grounded vac. When the connection is continuously antistatic , any static charge being produced by the flow goes all the way to ground through the vac. However, using a short jumper wire from the hose over the non-antistatic Y to the vac hose inlet will complete the connection and take care of the problem. Here is a pic of one that I did for my mounted , homemade boom arm. As you said , humid enviroments cause much less static. I have a good mix of dry and humid air over the course of the year. With out the antistatic I got zapped regularly by the hose. Why Fein doesn't do the antistatic thing is anybodys guess? Seth |
|
|
« Last Edit: March 30, 2011, 10:29 AM by SRSemenza »
|
Logged
|
Seth R. Semenza
S. R. Semenza Woodworking
Festool Service 800-554-8741
|
|
|
MarkF
Offline
Location: Concord, NC Member Since: Jan 2007
Posts: 272
Concord, NC
|
|
« Reply #14 on: March 30, 2011, 11:18 AM » |
|
Thanks Seth!
|
|
|
|
|
Logged
|
|
|
|
Julian Tracy
Offline
Location: Redford, MI Member Since: Oct 2007
Posts: 427
|
|
« Reply #15 on: March 30, 2011, 11:26 AM » |
|
In ten years of using my Fein Vac, I never once got zapped. I'm in MI though, but it gets dry around here at times.
JT
|
|
|
|
|
Logged
|
|
|
|
mishle
Offline
Location: Austin,TX Member Since: Jan 2009
Posts: 122
|
|
« Reply #16 on: March 30, 2011, 09:28 PM » |
|
Festool is the first vac that I actually need anti static with. I have run Shop vac, Ridgid, and craftsman with out static shock, just sawdust buildup.
I do like the cleaner hoses with anti-static:)
|
|
|
|
|
Logged
|
|
|
|
|
