Woodworking & Power Tools Forum - Festool Owners Group > FESTOOL DISCUSSIONS > Festool Jigs & Tool Enhancements > Homemade Boom Arm
Pages: [1]   Go Down
« previous next »
  Print  
Author Topic: Homemade Boom Arm  (Read 2909 times)
0 Members and 1 Guest are viewing this topic.
Noah Nordrum

Offline Offline

Location: Minneapolis, MN, US
Member Since: Jan 2011
Posts: 57
« on: November 06, 2011, 07:49 PM »
It's not portable by being on the vac, but made a boom arm for ~$6 with 1.5" pvc pipe and two 45 degree brackets.



I had to lift the vac up onto a table to get enough hose to be able to domino on the far side of the table, but you can't really complain too much about the minor shortcomings up a $6 boom arm Tongue Out

It's "attached" to the back leg of the table using zip ties.
Logged
MFT/3, CT26, TS55, OF1400, CXS, RO 90, RO 150, LR-32, Domino
Festool USA does not pre-approve the contents of this website nor endorse the application or use of any Festool product in any way other than in the manner described in the Festool Instruction Manual. To reduce the risk of serious injury and/or damage to your Festool product, always read, understand and follow all warnings and instructions in your Festool product's Instruction Manual. Although Festool strives for accuracy in the website material, the website may contain inaccuracies. Festool makes no representations about the accuracy, reliability, completeness or timeliness of the material on this website or about the results to be obtained from using the website. Festool and its affiliates cannot be responsible for improper postings or your reliance on the website's material. Your use of any material contained on this website is entirely at your own risk. The content contained on this site is provided for informational purposes only and does not constitute professional advice.

greenMonster

Offline Offline

Location: USA
Member Since: Aug 2011
Posts: 285
« Reply #1 on: November 06, 2011, 07:54 PM »
nice

Always wondered, isn't the pvc really floppy?
Also, it seems that just putting a couple hooks in the ceiling would work as well?
Logged
erock

Offline Offline

Location: cleveland, ohio
Member Since: Apr 2010
Posts: 559



WWW
« Reply #2 on: November 06, 2011, 08:13 PM »
Nice job.  I made a boom arm with 1 1/2" pvc.  Worked good for me also.  I see that you have a Dremel multi-max.   How do you like it?  I had one.  It last about 2 months on the job sites and the motor burned up on me. 

Eric
Logged
Kapex, Domino DF 500 Q set, Domino systainer,  HL 850 E plus with bench unit, OF1400, TS 55,  Trion PS 300, CXS set,  MFT 800, MFT1080,  MFT/3, CT 26, CT midi, DX93E, DX93 abrasive systainer,  DTS 400, DTS 400 abrasive systainer, Rotex 125,  ETS 125,  (2) ETS 125 abrasive systainer,  LR32 system, parallel guide extension kit, mini sys.,  multiple sys. 1-4,  sys toolbox, FS 3000/2,  (2) FS 1400/2,  FS 800/2, lots of clamps, tape measure, multi toolie, utility knife, safety glasses,  stein, folding rule, head lamp,  XL fleece, XL sweater,(2) XL t-shirt, XL long sleeve shirt, XL training shirt, XL polo shirt, beanie, hat, FOG cap,  banner, anti fatigue floor mat. 

I got a blog, check it out!     http://dustfreewoodworking.blogspot.com/
Noah Nordrum

Offline Offline

Location: Minneapolis, MN, US
Member Since: Jan 2011
Posts: 57
« Reply #3 on: November 06, 2011, 08:20 PM »
Quote from: greenMonster on November 06, 2011, 07:54 PM
Always wondered, isn't the pvc really floppy?
Also, it seems that just putting a couple hooks in the ceiling would work as well?

1.5" PVC was the point where it became rigid enough to use. I might do the ceiling hook route when I move back into the shop area. I'm currently in a temporary area while I put up a wall in the shop.

Quote from: erock on November 06, 2011, 08:13 PM
I see that you have a Dremel multi-max.   How do you like it?  I had one.  It last about 2 months on the job sites and the motor burned up on me. 
I think if I used a multi-max at work I'd get fired (I work in IT though, so construction work at your is frowned upon Tongue Out). It's okay. I thought it had a much higher learning curve than I expected. Much more of a finesse tool. I used it to cut the PVC pipe and I used it upstairs to cut away some hardwood flooring to bring it back to even with the door (was under some carpet initially). Seems to work okay if you're patient as it works slower than I keep expecting it to.
Logged
MFT/3, CT26, TS55, OF1400, CXS, RO 90, RO 150, LR-32, Domino
Pages: [1]   Go Up
  Print  
« previous next »
 
Jump to: