Author Topic: Homemade guide rail connectors (not your typical ones)  (Read 57742 times)

0 Members and 1 Guest are viewing this topic.

Offline Mixxedupmedia

  • Posts: 2
Re: Homemade guide rail connectors (not your typical ones)
« Reply #60 on: April 23, 2018, 10:56 AM »
Great ideas! I just joined the site ...should have done this before buying the stock connectors.😕
Bad decisions make the best stories.

Festool USA does not pre-approve the contents of this website nor endorse the application or use of any Festool product in any way other than in the manner described in the Festool Instruction Manual. To reduce the risk of serious injury and/or damage to your Festool product, always read, understand and follow all warnings and instructions in your Festool product's Instruction Manual. Although Festool strives for accuracy in the website material, the website may contain inaccuracies. Festool makes no representations about the accuracy, reliability, completeness or timeliness of the material on this website or about the results to be obtained from using the website. Festool and its affiliates cannot be responsible for improper postings or your reliance on the website's material. Your use of any material contained on this website is entirely at your own risk. The content contained on this site is provided for informational purposes only and does not constitute professional advice.


Offline mwest

  • Posts: 2
Re: Homemade guide rail connectors (not your typical ones)
« Reply #61 on: August 29, 2018, 02:06 PM »
In the original picture/posting, there are some 80/20 brackets hanging on the side of the MFT side rails. Are these modified to hang on the Festool MFT "extrusion"? I want to hang some small boxes for clamps and dawgs, etc. Any recommendations?

Offline brentasmith

  • Posts: 6
Re: Homemade guide rail connectors (not your typical ones)
« Reply #62 on: September 07, 2018, 11:08 PM »
I noticed Festool is extremely quiet on this thread...

I needed to join two rails and checked out connectors. Wow! $32 for a pair of metal bars with holes in them. You’ve got to be kidding. Profit margin must be over 90% on that thing <end of rant>.

I stopped by the hardware store to pick up a piece of metal about 12x6 mm. They didn’t carry that, but instead (as it turned out later fortunately) had one 12.7x3.2mm. I then realized I could do better than the stock part.

I often read complaints that joined rails don’t stay aligned together. Festool warns not to over tighten the screws, in fact, boasts flat heads to prevent just that. And the connectors are about only Festool item that has bad reviews on Amazon. No wonder they can’t be secured well; steel screws dig into soft aluminum rail.

My solution is to make the connector consisting of two thinner 3.2 mm parts (see picture). The top one has threaded holes with Allen screws (M6, 6mm long). The bottom one has non through (1/3 deep) cone shaped holes that align with the screws. These holes help to fully engage the threads and prevent lateral sliding of two parts. As you tighten the screws the two pieces are pushed apart and firmly press against inside of the slot distributing pressure over large area. You can tighten them very well.

While fitting the connectors I discovered that two t-slots of the guide rail have different width by about 0.3 mm and had to file the bars a bit :-(.

I tested the setup. After joining two rails I moved, rotated, flipped, lifted by one end, and kicked them around. Checked again with a straight edge – perfect.

P.S. Festool, if you like the idea e-mail me a thank you card attached to a banknote or a green tool of your choice :-)  [poke]

(Attachment Link)

Offline Cheese

  • Posts: 5060
Re: Homemade guide rail connectors (not your typical ones)
« Reply #63 on: September 08, 2018, 12:02 AM »
I noticed Festool is extremely quiet on this thread...

And FWIW...I don’t think Festool will weigh in on this one. From a corporate standpoint, they have way bigger fish to fry (from a class action suit perspective) with the Kapex self immolation issues.
There was a great thread about manufacturing your own connectors by another FOG member Malte. I can’t remember his web name... [crying]

Offline Peter Halle

  • Global Moderator
  • *
  • Posts: 11558
Re: Homemade guide rail connectors (not your typical ones)
« Reply #64 on: September 08, 2018, 07:42 AM »
Festool doesn't comment on many threads anymore.  I suspect that a thread that started 6 years ago and is about an accessory won't be noticed or rise to the top of the list.

Just my 2 cents.

Peter