Author Topic: LR...2?  (Read 1480 times)

0 Members and 1 Guest are viewing this topic.

Offline Scorpion

  • Posts: 555
LR...2?
« on: February 26, 2018, 11:29 PM »
I️ know this was likely not invented here but it works so darn well I️ decided I’d show it off.

I️ chose not to machine system holes in my shop shelves mostly because I️ forgot on the first assembly until it was on the wall.  Once in place, I️ realized my mistake and decided that the darn LR32 wouldn’t define me so I️ built a jig with two pieces of scrap, some CA glue, and 6 narrow crown staples.  Center hole fits those plunge style dowel bits which didn’t work because the hole itself prevented the chips from evacuating. I️ tried again by drilling the other four use with a Brad point bit.  Then I️ cut spacer blocs for each size systainer (like I️ do for drawer slides) and went to town.


Plans are available on my site (joke)




Sent from my iPad using Tapatalk Pro

Festool USA does not pre-approve the contents of this website nor endorse the application or use of any Festool product in any way other than in the manner described in the Festool Instruction Manual. To reduce the risk of serious injury and/or damage to your Festool product, always read, understand and follow all warnings and instructions in your Festool product's Instruction Manual. Although Festool strives for accuracy in the website material, the website may contain inaccuracies. Festool makes no representations about the accuracy, reliability, completeness or timeliness of the material on this website or about the results to be obtained from using the website. Festool and its affiliates cannot be responsible for improper postings or your reliance on the website's material. Your use of any material contained on this website is entirely at your own risk. The content contained on this site is provided for informational purposes only and does not constitute professional advice.


Offline live4ever

  • Posts: 771
Re: LR...2?
« Reply #1 on: February 27, 2018, 11:21 AM »
Does the jig work with non-Festool drills?
Current systainer to productivity ratio:  very high

Offline NL-mikkla

  • Posts: 249
  • www.m144h.com
Re: LR...2?
« Reply #2 on: February 27, 2018, 11:35 AM »
Super smart and simple idea!
well done

Offline android

  • Posts: 35
Re: LR...2?
« Reply #3 on: February 27, 2018, 01:03 PM »
Does the jig work with non-Festool drills?

I've made an adapter I'll sell you for $119.

Offline live4ever

  • Posts: 771
Re: LR...2?
« Reply #4 on: February 27, 2018, 02:26 PM »
Does the jig work with non-Festool drills?

I've made an adapter I'll sell you for $119.

If it's not red I don't want it.  Or at the very least, I hope it comes in a systainer.
Current systainer to productivity ratio:  very high

Offline Gerald_D

  • Posts: 302
Re: LR...2?
« Reply #5 on: February 27, 2018, 02:49 PM »
Nice idea- but I'm sure it's NAINA....

Regards,
Gerald
Gerald
I have Festools- Big and Small and a few other tools

Offline sheperd80

  • Posts: 118
Re: LR...2?
« Reply #6 on: February 27, 2018, 10:31 PM »
So $140 day after tomorrow???

Sent from my SAMSUNG-SM-G890A using Tapatalk


Offline Scorpion

  • Posts: 555
Re: LR...2?
« Reply #7 on: February 28, 2018, 12:15 AM »
Does the jig work with non-Festool drills?

I've made an adapter I'll sell you for $119.

If it's not red I don't want it.  Or at the very least, I hope it comes in a systainer.

Yes it does!  A Red Sys5 actually.


Sent from my iPhone using Tapatalk Pro