Author Topic: Parf Guide mark 2 issues and questions  (Read 8445 times)

0 Members and 1 Guest are viewing this topic.

Online Mario Turcot

  • Posts: 752
Re: Parf Guide mark 2 issues and questions
« Reply #60 on: February 08, 2019, 09:04 PM »
Another good option from TSO for the U.S.

Its all about options. Down under with US dollar and postage costs someone like Yellowbox shed is great for Aussies/Kiwis and another great option if you 3D Print.

OT. I want to buy $35 worth of Robertson bits (square) from Canada at a postage cost of $120CA!!

I hear you about postage fees. The order I did with Yellowboxshed came at a total of 96$ and the postage was 14.50$ I call this extremely fair. Personally I tried several times to order from Woodpecker Tools. Just last week they had a router bit I just received from Toolstoday, Toolstoday charged me 26$ for shipping, there was 2 bits. Woodpecker was charging me 37$ for a single bit and the bit was 35$  [eek]


Mario

Festool USA does not pre-approve the contents of this website nor endorse the application or use of any Festool product in any way other than in the manner described in the Festool Instruction Manual. To reduce the risk of serious injury and/or damage to your Festool product, always read, understand and follow all warnings and instructions in your Festool product's Instruction Manual. Although Festool strives for accuracy in the website material, the website may contain inaccuracies. Festool makes no representations about the accuracy, reliability, completeness or timeliness of the material on this website or about the results to be obtained from using the website. Festool and its affiliates cannot be responsible for improper postings or your reliance on the website's material. Your use of any material contained on this website is entirely at your own risk. The content contained on this site is provided for informational purposes only and does not constitute professional advice.


Offline ChuckM

  • Posts: 812
Re: Parf Guide mark 2 issues and questions
« Reply #61 on: February 08, 2019, 09:15 PM »
Cross shipping costs have prevented me from buying more tools or things from the US. Recently, I bought some magazines on eBay and had them shipped to a US address free; to a Canadian location? The shipping cost would be five times the total cost of the magazines!

Another reason why I shop mostly at Lee Valley for woodworking tools, and any vendor whose products are not carried by Lee Valley, or any local tool vendors in Canada seldom gets my business.

Offline TSO Products

  • Retailer
  • *
  • Posts: 703
    • TSO Products
Re: Parf Guide mark 2 issues and questions
« Reply #62 on: February 08, 2019, 09:17 PM »
Another good option from TSO for the U.S.

Its all about options. Down under with US dollar and postage costs someone like Yellowbox shed is great for Aussies/Kiwis and another great option if you 3D Print.

OT. I want to buy $35 worth of Robertson bits (square) from Canada at a postage cost of $120CA!!

Non-US woodworkers:
TSO hears you. Until we developed capable Dealers in key geographic areas we subsidized international shipping so we know from our own pocketbook how expensive that is [sad].

Since then we have established  capable stocking dealers in Australia and New Zealand CARBATEC, in Europe AXMINSTER and GereedschapPro plus South Africa's BPM TOOLCRAFT and HARDWARE CENTRE with ULTIMATE TOOLS in Canada our very first International Dealer.

We thank them all for offering our customers a choice.

Hans and Eric
TSOproducts.com

Home of the GRS-16 and GRS-16 PE  plus TPG Parallel Guide -  the MTR-18 Triangle and Work Holding solutions plus AXMINSTER UJK in the USA

Offline Jiggy Joiner

  • Posts: 38
Re: Parf Guide mark 2 issues and questions
« Reply #63 on: February 09, 2019, 04:37 AM »
After reading this thread I checked my Parf sticks and they seem spot on, mine is a Mk 2 system. Whenever I make a top of any type with the system, I always check for square cutting etc, and from the many I’ve made so far, all seems fine and on par with my MFT/3.
Hopefully any faulty versions of the systems are few and far between.

I also just want to reassure anybody thinking of buying these systems, or anything else from Axminster Tools. Apart from a possible inconvenience if something is damaged, not up to standard, or any other cause for disappointment, rest assured Axminster will sort it out and make sure you are happy.
Without going into detail, I use many suppliers and buy tools from many companies, and without doubt, Axminster have the best customer service, that I have personally ever experienced. That alone means a lot too me.

Offline Peter Parfitt

  • Magazine/Blog Author
  • *
  • Posts: 4128
    • New Brit Workshop on YouTube
Re: Parf Guide mark 2 issues and questions
« Reply #64 on: February 09, 2019, 07:17 AM »
After reading this thread I checked my Parf sticks and they seem spot on, mine is a Mk 2 system. Whenever I make a top of any type with the system, I always check for square cutting etc, and from the many I’ve made so far, all seems fine and on par with my MFT/3.
Hopefully any faulty versions of the systems are few and far between.

I also just want to reassure anybody thinking of buying these systems, or anything else from Axminster Tools. Apart from a possible inconvenience if something is damaged, not up to standard, or any other cause for disappointment, rest assured Axminster will sort it out and make sure you are happy.
Without going into detail, I use many suppliers and buy tools from many companies, and without doubt, Axminster have the best customer service, that I have personally ever experienced. That alone means a lot too me.

I absolutely agree and it was one of the major factors that convinced me that they should take on my Parf (R) products.

Peter

Offline Euclid

  • Posts: 135
Re: Parf Guide mark 2 issues and questions
« Reply #65 on: February 09, 2019, 08:36 AM »
Whilst we are on the subject of Axminster (rather than specifically the ‘PGS’)...

Although I’d bought from Axminster by mail order (online) a number of times in the past (with considerable satisfaction - well, total satisfaction to be honest), I’d never visited one of their stores.
Having now done that (my “local” one, in Kent - not the easiest of journeys) I’ve been back several times because it is just a nice place to go... calm and spacious, loads of kit to look at and accessories to browse, and good relaxed atmosphere. The staff seem to be endlessly patient and helpful, knowledgeable and enthusiastic, with no pressure to buy and leave you alone until you want help. Odd items that have been out-of-stock, they have sent on to me free of delivery charges.

My only real “complaint” is that on each visit I’ve bought (and spent) much more than I intended when I left home...!

Sorry if all of that sounds like a “shill” or covert marketing for them, but it isn’t... I just feel they deserve a  public “thumbs up”. Yes, some of the stuff (eg. Some Festool items, but not all) can be found a little bit cheaper elsewhere, but overall ther prices seem very fair and sometimes very good; I’m happy to support, when I can, a business that provides both good service online and an extremely good “bricks-and-mortar” presence.

I’ve been buying quite a bit of “UJK” stuff lately and am very pleased with the quality and the finish; though I don’t (yet) have a Parf Guide System...
« Last Edit: February 09, 2019, 08:40 AM by Euclid »

Offline Bill Fleming

  • Posts: 21
Re: Parf Guide mark 2 issues and questions
« Reply #66 on: February 09, 2019, 11:51 AM »
I am in need of a new top for my MFT/1080 and the cost of a new top is about equal to the MK2 and of course with the MK2 I can do many things.

So is all this issue of MK2 quality sorted such that getting a properly machined and packaged version more likely than not?

Thx Bill

Offline TSO Products

  • Retailer
  • *
  • Posts: 703
    • TSO Products
Re: Parf Guide mark 2 issues and questions
« Reply #67 on: February 09, 2019, 12:11 PM »
I am in need of a new top for my MFT/1080 and the cost of a new top is about equal to the MK2 and of course with the MK2 I can do many things.

So is all this issue of MK2 quality sorted such that getting a properly machined and packaged version more likely than not?

Thx Bill
@Bill Fleming - based on the answer I received earlier this week from a senior technical manager at AXMINSTER the answer is an unqualified YES.

TSO's stock replenishment order from AXMINSTER with PGS Mark 2 was ready to ship to us by airfreight. Sign up here to be notified when PGS Mark 2 is back in stock here in the US:

            https://tsoproducts.com/workholding-accessories/ujk-technology-parf-guide-system/


Hans
TSOproducts.com

Home of the GRS-16 and GRS-16 PE  plus TPG Parallel Guide -  the MTR-18 Triangle and Work Holding solutions plus AXMINSTER UJK in the USA

Offline Bill Fleming

  • Posts: 21
Re: Parf Guide mark 2 issues and questions
« Reply #68 on: February 09, 2019, 01:24 PM »
Great news, signed up to be notified on your site!

Thx Bill

Offline box185

  • Posts: 52
Re: Parf Guide mark 2 issues and questions
« Reply #69 on: February 10, 2019, 01:47 PM »
I checked the third pair of Parf Sticks that I received from Axminster - greatly improved, but still the patterned error.

About 0.003 inch difference between adjacent hole pair. Good enough already . . . move along.

Axminster has done a great job following up on this issue. Still curious how a patterned error appears, but it doesn't matter.

Offline Mike Goetzke

  • Posts: 159
Re: Parf Guide mark 2 issues and questions
« Reply #70 on: February 11, 2019, 09:54 AM »
Talked to Axminster this morning and they say don’t expect availability until mid-March! I need to look for CNC supplier for my three new tops.

Offline TSO Products

  • Retailer
  • *
  • Posts: 703
    • TSO Products
Re: Parf Guide mark 2 issues and questions
« Reply #71 on: February 11, 2019, 11:13 AM »
Talked to Axminster this morning and they say don’t expect availability until mid-March! I need to look for CNC supplier for my three new tops.

Mike, - we just received confirmation that our AXMINSTER shipment has shipped airfreight to TSO's Minnesota warehouse. Should be available to ship out to our customers some time next week. automatic notifications will go out to all who have signed up on our website:

         https://tsoproducts.com/workholding-accessories/ujk-technology-parf-guide-system/

Hans
TSOproducts.com

Home of the GRS-16 and GRS-16 PE  plus TPG Parallel Guide -  the MTR-18 Triangle and Work Holding solutions plus AXMINSTER UJK in the USA