Author Topic: Pegboard Source For Woodrave Jig  (Read 841 times)

0 Members and 1 Guest are viewing this topic.

Offline SonOfMI

  • Posts: 8
Pegboard Source For Woodrave Jig
« on: November 10, 2017, 07:09 PM »
Pegboard isn't something I work with much. I've been working on a new work table in my free time and am getting close to routing the holes in the top. I bought the woodrave jig and spent some time checking pegboard locally. I haven't found any that has holes straight and square with each other. For those who have used the woodrave jig for custom MFT tops and gotten holes straight and square with each other, where did you get the pegboard from? I live in Atlanta.

Festool USA does not pre-approve the contents of this website nor endorse the application or use of any Festool product in any way other than in the manner described in the Festool Instruction Manual. To reduce the risk of serious injury and/or damage to your Festool product, always read, understand and follow all warnings and instructions in your Festool product's Instruction Manual. Although Festool strives for accuracy in the website material, the website may contain inaccuracies. Festool makes no representations about the accuracy, reliability, completeness or timeliness of the material on this website or about the results to be obtained from using the website. Festool and its affiliates cannot be responsible for improper postings or your reliance on the website's material. Your use of any material contained on this website is entirely at your own risk. The content contained on this site is provided for informational purposes only and does not constitute professional advice.


Offline ear3

  • Posts: 3344
Re: Pegboard Source For Woodrave Jig
« Reply #1 on: November 11, 2017, 08:19 AM »
I had a similar difficulty, where the pegboard I sourced at the local Home Depot was ill-fitting for the Woodrave jig -- the pins at the bottom of the jig were difficult to fit into some of the holes.  In the end I gave up on the idea that I could produce CNC level precision holes with the jig and just muddled through.  I'm happy with the results, but I would never use the hole pattern for rail alignment or to check square.
Kapex KS 120 w/UG Cart and Extensions • CXS Set • T18+3 w/Centrotec Installer's Set • PDC 18/4 • TS 75 • TSC 55 • HKC 55 w/250, 420 and 670 FSK rails • Carvex 420 w/Accessory Kit • Domino 500 Set • Domino 700 XL • OF 2200 w/Base Accessory Kit • OF 1400 • OF 1010 • MFK 700 EQ Set • LR 32 • MFS 400 w/2000, 1000, and 700 extensions • Rotex 90 • Rotex 150 • LS 130 • ETS-EC 150/5 • ETS 150/3 • Pro 5 LTD • RTS 400 • RAS 115.04 • DX 93 • RS 2 • HL 850 • Vecturo OS 400 • CT 26 w/Long-Life Bag • CT Sys w/Long-Life Bag • MFT/3

Online DynaGlide

  • Posts: 58
Re: Pegboard Source For Woodrave Jig
« Reply #2 on: November 11, 2017, 10:57 AM »
I called a local lumber dealer and they sold be a scrap piece of 1/4" pegboard. It worked well for drilling the holes. Square as far as I can tell.

Offline Dane

  • Posts: 298
Re: Pegboard Source For Woodrave Jig
« Reply #3 on: November 11, 2017, 04:32 PM »
Home Depot sells super lousy pegboard.  I took the Woodrave jig to Lowe’s and tested the brand they sell and it fit perfectly.  I got what I’d consider CNC level accuracy- no perceived error with a woodpecker square. 

Offline JimD

  • Posts: 325
Re: Pegboard Source For Woodrave Jig
« Reply #4 on: November 13, 2017, 06:54 PM »
I am not sure where the pegboard I used came from but I think it was Home Depot.  The holes were not perfectly aligned.  They obviously moved less than the diameter of a hole from one end of the sheet to the other, less than 1/4 inch in 8 feet.  Because of that, I did not expect squaring jigs to work.  But they do.  I cannot detect any out of square.  I believe that may be due, at least in part, to the relatively small error in hole placement compared to the size of my squares.  Square layout is also relative to each other, not whether the holes are in a perfect line.  In any event, it worked out better than I expected.

I do not use dogs to align my rails for crosscuts but I may try that too.  So far I just draw a line with a square and cut to it.  Or I use a Ron Paulk style crosscut jig.