Having trouble with your Festool power tool? Well, we're here to help you. Before posting to the forum, give us a chance to diagnose and resolve your issue. In the U.S. and Canada, call us toll-free at 888-337-8600 on Monday-Friday between 8a-5p EST or contact us via email at service@festoolusa.com. For other countries, please visit http://www.festool.com for contact information for your local Festool service department.

Author Topic: Domino 500 Threaded Insert in Base? Insert came out  (Read 308 times)

0 Members and 1 Guest are viewing this topic.

Offline TheSergeant

  • Posts: 74
Domino 500 Threaded Insert in Base? Insert came out
« on: November 28, 2017, 06:36 PM »
Are all Domino's built like this or was mine repaired and sent out like this?  Looks like there is a Helicoil insert in the base of the machine.   I went to remove the accessory base and the insert came out with the screw  I don't have any metric imperial Helicoil components.  How do I install this?


Festool USA does not pre-approve the contents of this website nor endorse the application or use of any Festool product in any way other than in the manner described in the Festool Instruction Manual. To reduce the risk of serious injury and/or damage to your Festool product, always read, understand and follow all warnings and instructions in your Festool product's Instruction Manual. Although Festool strives for accuracy in the website material, the website may contain inaccuracies. Festool makes no representations about the accuracy, reliability, completeness or timeliness of the material on this website or about the results to be obtained from using the website. Festool and its affiliates cannot be responsible for improper postings or your reliance on the website's material. Your use of any material contained on this website is entirely at your own risk. The content contained on this site is provided for informational purposes only and does not constitute professional advice.


Offline Bohdan

  • Posts: 796
Re: Domino 500 Threaded Insert in Base? Insert came out
« Reply #1 on: November 28, 2017, 06:59 PM »
This happened to me.

It is almost impossible to reinstate a helicoil that has come out because it reduces in diameter as you use the tool to screw it in.

In AU the festool warranty service doesn't replace helicoils only the complete base. I found that it was much cheaper, quicker and easier to just buy the stainless steel helicoils on ebay and fit them myself, than it was to lose the tool for several weeks while it was being shipped and repaired.

I also used some loctite high strength retaining compound when I inserted the new helicoil to ensure that it didn't happen again.

I think that the original helicoils used by festool are too short and the ones that I used were longer.

BTW the replacement helicoils were about $3 delivered for a packet of 10.

Offline Peter Halle

  • Global Moderator
  • *
  • Posts: 10925
  • Let's Redux / Revive / Rewind / Rollback the FOG!
Re: Domino 500 Threaded Insert in Base? Insert came out
« Reply #2 on: November 28, 2017, 07:02 PM »
I would suggest that you contact Festool at the phone number on a lebel on your tool and talk to them.

Peter
Disclaimer:  I have been involved with the development of some TSO Products.  I have offered thoughts and ideas freely.  I am not paid but I may receive products during the development process or afterwards.

Offline Cheese

  • Posts: 3709
Re: Domino 500 Threaded Insert in Base? Insert came out
« Reply #3 on: November 28, 2017, 07:06 PM »
Yours is normal, what’s not normal is that the helicoil came out.  [eek]

You’ll need to get a new helicoil or send her in to Festool. Helicoils come with a small tang that allows you to wind it around an insertion mandrel. Once inserted, the tang is broken off and the helicoil expands to tightly fit the tapped hole. Without a tang, you can’t reduce the helicoil OD to fit inside the threaded ID. Sorry... [sad] [crying]

Offline TheSergeant

  • Posts: 74
Re: Domino 500 Threaded Insert in Base? Insert came out
« Reply #4 on: November 28, 2017, 08:26 PM »
I completely forgot about the tang.  It's been awhile since I've had to use a Helicoil.  I have a bunch of the smaller sized imperial inserts and prewinders but no metric.  I looked and it's like $30 for a kit, which I'd only use once.  I don't have to have to ship the tool back for something so small.  Time to call around to friends.  Thanks!