Having trouble with your Festool power tool? Well, we're here to help you. Before posting to the forum, give us a chance to diagnose and resolve your issue. In the U.S. and Canada, call us toll-free at 888-337-8600 on Monday-Friday between 8a-5p EST or contact us via email at service@festoolusa.com. For other countries, please visit http://www.festool.com for contact information for your local Festool service department.

Author Topic: HKC fouling splinterguard  (Read 1353 times)

0 Members and 1 Guest are viewing this topic.

Offline Pykie

  • Posts: 36
HKC fouling splinterguard
« on: May 18, 2017, 02:35 AM »
Hey guys, having an issue with a HKC ive recently been running though its paces.

I've got a TS55 as well as a TS75 and never had this issue with the s;inter guard like this, only the glue detatching when it needs replacing.

I went through 3 pieces of splinter guard rubber today as the saw kept fouling the splinter guard and over cutting it closer to the aluminium track, then causing a furry cut with small tear out where the splinter guard had been cut back.

I thought it might have been a once off but once I replaced the guard, within 7-8 cuts it had fouled the rubber strip.

All these cuts were on 0 degrees and on the HKC 420.

This is the 18v HKC 55.

Festool USA does not pre-approve the contents of this website nor endorse the application or use of any Festool product in any way other than in the manner described in the Festool Instruction Manual. To reduce the risk of serious injury and/or damage to your Festool product, always read, understand and follow all warnings and instructions in your Festool product's Instruction Manual. Although Festool strives for accuracy in the website material, the website may contain inaccuracies. Festool makes no representations about the accuracy, reliability, completeness or timeliness of the material on this website or about the results to be obtained from using the website. Festool and its affiliates cannot be responsible for improper postings or your reliance on the website's material. Your use of any material contained on this website is entirely at your own risk. The content contained on this site is provided for informational purposes only and does not constitute professional advice.


Offline Peter Halle

  • Global Moderator
  • *
  • Posts: 10474
  • Let's Redux / Revive / Rewind / Rollback the FOG!
Re: HKC fouling splinterguard
« Reply #1 on: May 18, 2017, 07:59 AM »
Perhaps this will be a stupid suggestion, but you might want to take the blade off and reinstall it again to make sure that it seats  properly and that it is tight.

Peter
Scraps to Smiles.  To be continued.....  Stay Tuned.

Offline demographic

  • Posts: 276
Re: HKC fouling splinterguard
« Reply #2 on: May 18, 2017, 05:26 PM »
No chance the blade could be warped?
It's pretty slim and can be damaged if its stopped in the cut and pulled out badly.

Offline Cheese

  • Posts: 2937
Re: HKC fouling splinterguard
« Reply #3 on: May 18, 2017, 08:59 PM »
I'd echo Peter's suggestion, remove the blade and clean the arbor, washer and nut and look for anything that could interfere with the proper mounting of the blade. Also look for any small metal burrs that may have gone unnoticed during the assembly process.

Offline bryan1982

  • Posts: 124
Re: HKC fouling splinterguard
« Reply #4 on: May 19, 2017, 12:45 AM »
Check to make sure the saw is running tight on the guide rail

Offline RTC

  • Posts: 2
Re: HKC fouling splinterguard
« Reply #5 on: May 20, 2017, 10:11 PM »
My HKC has also cut the splinter guard slightly unevenly. Not so much that it's been an issue. I have been putting the saw through its paces cutting stringers and rafters from wet lumber. So the minute blade drift seemed acceptable.  My splinter guard is slightly furry at the farthest point where the saw rarely travels.

Offline Pykie

  • Posts: 36
Re: HKC fouling splinterguard
« Reply #6 on: Yesterday at 06:35 AM »
Just an update on this.

Blade was installed correctly, was running fine on the track.

I think it's blade deflection in the 32mm hardwood decking. There's even a small knick in the aluminium on the track, so a good 2-3mm deflection in the blade to hit that.

I went through a fair bit of splinterguard sorting it out. Still not great and the cut quality isn't as good as a TS55.

The spring has already failed in the retractable guard as well.

Reconsidering weather or not to buy the HK 85 now.

Offline SRSemenza

  • Global Moderator
  • *
  • Posts: 7623
  • Finger Lakes Region, NY State , USA
Re: HKC fouling splinterguard
« Reply #7 on: Yesterday at 10:04 AM »
        When comparing cut quality make sure the same type of blade is being compared. I don't know if you have blades other than those that come on the saws but just for peoples general info. HKC comes with an 18 tooth blade that probably has a tooth geometry that is a compromise for rip and crosscuts. While the TS55 comes with a 48 tooth blade that is optimized for crosscuts and sheet goods.

Seth