Having trouble with your Festool power tool? Well, we're here to help you. Before posting to the forum, give us a chance to diagnose and resolve your issue. In the U.S. and Canada, call us toll-free at 888-337-8600 on Monday-Friday between 8a-5p EST or contact us via email at service@festoolusa.com. For other countries, please visit http://www.festool.com for contact information for your local Festool service department.

Author Topic: Kapex repair experience  (Read 375 times)

0 Members and 1 Guest are viewing this topic.

Offline Blackberry

  • Posts: 64
  • .
Kapex repair experience
« on: November 30, 2017, 07:52 PM »
This past week a good friend of mine who's a woodworker came over to use my 6 year old Kapex. He was cutting 4"x4"x4" hard maple squares. He was cutting 8 degree bevels on four sides.  As things go when you lend or borrow stuff sometimes things break (see Murphy's Law).  The saw grabbed the hunk of wood and sent it flying. Thankfully my friend wasn't hurt!  Embarrassed and apologetic together we assessed the situation. The piece was difficult to hold onto and the feed rate was too fast. Nothing to do with the saw engineering or its performance.  Further inspection showed the saw had a bad wobble. A change of blade didn't seem to remedy the situation.

Hmmm clearly out of warranty and user error, I assumed the repair was most likely going to be expensive. Honestly that's ok because nobody got hurt! Nothing I could do but send the saw to Lebanon Indiana for repairs. 

This is where repairman Brad took possession of my saw and began his work. Brad was very professional as he explained the damage and how the design of the inner flange that holds the blade aided in preventing further damage. He showed me there's a lining on the flange that allow it to serve as a clutch allowing the blade to turn before holding the power of the motor back under stress.  Brad tested and tuned the accuracy of the saw and I already have it back in operation in the shop.

This post is in no way intended to minimize anyone else's service experience. However I felt it would be very remiss of me not to share a genuine experience. The speed of service and the personal attention I was given didn't go unnoticed.  Additionally I was pleasantly surprised at the repair bill!

Thank you Festool & Brad

Festool USA does not pre-approve the contents of this website nor endorse the application or use of any Festool product in any way other than in the manner described in the Festool Instruction Manual. To reduce the risk of serious injury and/or damage to your Festool product, always read, understand and follow all warnings and instructions in your Festool product's Instruction Manual. Although Festool strives for accuracy in the website material, the website may contain inaccuracies. Festool makes no representations about the accuracy, reliability, completeness or timeliness of the material on this website or about the results to be obtained from using the website. Festool and its affiliates cannot be responsible for improper postings or your reliance on the website's material. Your use of any material contained on this website is entirely at your own risk. The content contained on this site is provided for informational purposes only and does not constitute professional advice.


Offline Brice Burrell

  • Posts: 7257
  • Remodeling Contractor
    • The Green and Dark Blue blog
Re: Kapex repair experience
« Reply #1 on: November 30, 2017, 09:36 PM »
Its always good to hear the positives experiences.  Thanks for posting.
Check out my new blog, The Green and Dark Blue Blog.

Offline aloysius

  • Posts: 199
Re: Kapex repair experience
« Reply #2 on: November 30, 2017, 09:51 PM »
One particularly positive aspect of SCMS in general, in comparison to Radial Arm Saws in particular, is their general reluctance to "grab" or "snatch" the workpiece.  Radial Arms, with their climbing cuts, are all too willing to grab.

Probably the single biggest reason for them being banned nowadays in many jurisdictions.
FOG-wit since '95:  Some say since birth...

Offline ear3

  • Posts: 3402
Re: Kapex repair experience
« Reply #3 on: December 01, 2017, 07:45 AM »
Fantastic news!  Thanks for sharing.
Kapex KS 120 w/UG Cart and Extensions • CXS Set • T18+3 w/Centrotec Installer's Set • PDC 18/4 • TS 75 • TSC 55 • HKC 55 w/250, 420 and 670 FSK rails • Carvex 420 w/Accessory Kit • Domino 500 Set • Domino 700 XL • OF 2200 w/Base Accessory Kit • OF 1400 • OF 1010 • MFK 700 EQ Set • LR 32 • MFS 400 w/2000, 1000, and 700 extensions • Rotex 90 • Rotex 150 • LS 130 • ETS-EC 150/5 • ETS 150/3 • Pro 5 LTD • RTS 400 • RAS 115.04 • RS 2 • HL 850 • Vecturo OS 400 • CT 26 w/Long-Life Bag • CT Sys w/Long-Life Bag • MFT/3