Having trouble with your Festool power tool? Well, we're here to help you. Before posting to the forum, give us a chance to diagnose and resolve your issue. In the U.S. and Canada, call us toll-free at 888-337-8600 on Monday-Friday between 8a-5p EST or contact us via email at service@festoolusa.com. For other countries, please visit http://www.festool.com for contact information for your local Festool service department.

Author Topic: sanding swirl marks  (Read 5178 times)

0 Members and 1 Guest are viewing this topic.

Offline Carl

  • Posts: 8
sanding swirl marks
« on: August 30, 2007, 10:30 PM »
Hello all!
I was wondering if any of you has ever experienced swirls in the wood and laquer when using the ETS 150/3 sander.  I finish to 150 grit on wood and laquer, and use 320 grit, both seem to leave swirl marks.  I always end up finishing the sanding by hand to eliminate these marks, and I'm  hoping someone can tell me if there's any way to avoid these swirls.
I thank you in advance for your help!
Carl ???

Festool USA does not pre-approve the contents of this website nor endorse the application or use of any Festool product in any way other than in the manner described in the Festool Instruction Manual. To reduce the risk of serious injury and/or damage to your Festool product, always read, understand and follow all warnings and instructions in your Festool product's Instruction Manual. Although Festool strives for accuracy in the website material, the website may contain inaccuracies. Festool makes no representations about the accuracy, reliability, completeness or timeliness of the material on this website or about the results to be obtained from using the website. Festool and its affiliates cannot be responsible for improper postings or your reliance on the website's material. Your use of any material contained on this website is entirely at your own risk. The content contained on this site is provided for informational purposes only and does not constitute professional advice.


Online Corwin

  • Posts: 2560
Re: sanding swirl marks
« Reply #1 on: August 31, 2007, 01:19 AM »
Slow down...  Check out this Hint from Festool's site.
Looks like your rabbit joint is a hare off! ;)

Offline Timmy C

  • Posts: 462
Re: sanding swirl marks
« Reply #2 on: August 31, 2007, 07:04 AM »
Carl, as corwin says, slow down a bit.  I like to use the foam interface pad when working on the finishing aspece ot things.  If you are using a vac attached, try turning to the "turtle" speed as well.  There are occasions where the vac will actually suck the sander down onto the work piece and cause the swirling effect, or the fish-eye thing going on.  God luck, and relax a bit in the sanding.  I find that about 10 minutes of yoga, and 20 minutes or so of Tai Chi right before sanding puts me into the mode of acceptance and tolerance needed to sand properly.

Timmy C

Offline Dan Clark

  • Posts: 545
    • talkFestool
Re: sanding swirl marks
« Reply #3 on: August 31, 2007, 09:41 AM »
Carl,

I'm not sure if Tai Chi or Yoga will help, but it's very possible that the swirls are caused by the sander sucking down to the wood and then releasing.  If the swirls are uneven and inconsistant, this is probably the culprit.   

What I do is back suction down to at least the 50% position even with heavy grit paper.   I go lower with finer grits.    You really need only enough suction to remove the dust.  At full power, the CT series is WAY too powerful.   (In other words, they really suck!)

Give that a try and let us know if that fixes the problem.

Regards,

Dan.

Offline Carl

  • Posts: 8
Re: sanding swirl marks
« Reply #4 on: August 31, 2007, 07:45 PM »
 :D
Thanks for your comments I turned down the vac on all sanding and slowed down the orbital sander.  That made a huge change to where the swirls are  barely visible.  Thanks for your help! I  should have  figured it out on my own but I thought I'd ask.
Have a great weekend!
Carl