Having trouble with your Festool power tool? Well, we're here to help you. Before posting to the forum, give us a chance to diagnose and resolve your issue. In the U.S. and Canada, call us toll-free at 888-337-8600 on Monday-Friday between 8a-5p EST or contact us via email at service@festoolusa.com. For other countries, please visit http://www.festool.com for contact information for your local Festool service department.

Author Topic: TS 55 REQ blade squareness and cut problems  (Read 1950 times)

0 Members and 1 Guest are viewing this topic.

Offline estesbubba

  • Posts: 14
TS 55 REQ blade squareness and cut problems
« on: October 24, 2015, 04:42 PM »
Other than cutting the track strip I'm finally using my TS 55 REQ for the first time. I'm using it to crosscut 8/4 hard maple and the first thing I noticed is the blade isn't at 90. I loosened both ends, moved it back until it stopped, tighten the rear knob then the front. Did another test cut and same problem. Got the supplemental manual out and couldn't find anything on adjusting to 90. Found a little set screw by the 0 indicator and tried that. After several iterations and test cuts my gauge went from 0 to 1/2 but now my cuts are wacky. I'm using a jointed board and Woodpecker's square and here is what I'm seeing. The front edge of the board has light at the bottom (like this /) and rear has light at the top (like this \). I loosed and tightened the knobs and did a few more test cuts and same results. I clamp my track down with each cut.

Any ideas on what is going on and how to correct them? Am I not adjusting blade squareness correctly?

Festool USA does not pre-approve the contents of this website nor endorse the application or use of any Festool product in any way other than in the manner described in the Festool Instruction Manual. To reduce the risk of serious injury and/or damage to your Festool product, always read, understand and follow all warnings and instructions in your Festool product's Instruction Manual. Although Festool strives for accuracy in the website material, the website may contain inaccuracies. Festool makes no representations about the accuracy, reliability, completeness or timeliness of the material on this website or about the results to be obtained from using the website. Festool and its affiliates cannot be responsible for improper postings or your reliance on the website's material. Your use of any material contained on this website is entirely at your own risk. The content contained on this site is provided for informational purposes only and does not constitute professional advice.


Offline grbmds

  • Posts: 1728
Re: TS 55 REQ blade squareness and cut problems
« Reply #1 on: October 24, 2015, 05:43 PM »
This was a problem identified by others. There is a process which was outlined on the FOG some time ago to set the 0 degree stop. I think if you search using either "square" or "perpendicular" or "90 degree" and TS55 you should be able to find these posts. While some others have said they have had this as an ongoing problem, once I set my stop I have not had the problem again.

There are also posts which tell how to install a set screw in the appropriate place (duplicating the design of the previous version of the TS55) but I don't have those references and I did not find the need to do that so far.

Hopefully others can provide the exact links for these references.
Randy

Offline bkharman

  • Posts: 1939
Re: TS 55 REQ blade squareness and cut problems
« Reply #2 on: October 24, 2015, 05:46 PM »
It sounds like you are getting deflection on the blade through that hard maple. It is a lot of depth for the 55. I have a 75 I use through that material.

You can run through it a few times to see if that helps. Set the saw to cut 15 -25mm at a time. It will take longer, but the cut might be a lot better.

My .02

Cheers. Bryan.
People, I just want to say, you know, can we all get along? Can we get along?

Offline Joszef

  • Posts: 2
Re: TS 55 REQ blade squareness and cut problems
« Reply #3 on: September 06, 2017, 02:52 PM »
I am having the same problem on soft wood. Tried everything in the owners group suggestions. I feel I have a new shelf tool. It is great on the shelf.