Author Topic: Lr32 system and rail  (Read 3424 times)

0 Members and 1 Guest are viewing this topic.

Lr32 system and rail
« on: July 05, 2018, 11:27 AM »
Hello,
Just wondering what your thoughts are on the lr32 system with guide rail?
Is it Worth the money? Does it save you time and is it accurate?
I’m doing more and more alcove units with adjustable shelving and hoping to speed the process up somewhat.
Many thanks,
Louis

Festool USA does not pre-approve the contents of this website nor endorse the application or use of any Festool product in any way other than in the manner described in the Festool Instruction Manual. To reduce the risk of serious injury and/or damage to your Festool product, always read, understand and follow all warnings and instructions in your Festool product's Instruction Manual. Although Festool strives for accuracy in the website material, the website may contain inaccuracies. Festool makes no representations about the accuracy, reliability, completeness or timeliness of the material on this website or about the results to be obtained from using the website. Festool and its affiliates cannot be responsible for improper postings or your reliance on the website's material. Your use of any material contained on this website is entirely at your own risk. The content contained on this site is provided for informational purposes only and does not constitute professional advice.


Offline clark_fork

  • Posts: 272
Re: Lr32 system and rail
« Reply #1 on: July 05, 2018, 12:07 PM »
Outside of the patience needed to overcome the learning curve, the main emphasis of the system is that it is not confined to just making shelf pin holes. It is set up to accurately place European hinges and place drawer slides.

Therefore, if your intent is to solely drill shelf pin holes in a fixed position, one of the readily available shelf pin jigs would serve your needs.

A secondary concern might be that the system is metric based and this might also add to learning time as well require some metric measuring items. However, essentially it is a clever logical system that once learned is a worthy addition to any shop even those where the use might be limited.

On a personal note, I had a good experience in the learning mode watching videos by erock of the Poplar Shop.   
Clark Fork

"A lot of people are afraid of heights. Not me, I'm afraid of widths."  Stephen Wright

"straight, smooth and square" Mr. Russell, first day high school shop class-1954

" What's the good of it?" My Sainted Grandmother

"You can't be too rich, too thin or have too many clamps." After my introduction to pocket joinery and now the MFT work process

"Don't make something unless it is both made necessary and useful; but if it is both necessary and useful,
don't hesitate to make it beautiful." -- Shaker dictum

Offline cpw

  • Posts: 80
Re: Lr32 system and rail
« Reply #2 on: July 05, 2018, 10:41 PM »
I've found using the OF1010 router with the LR32 is much faster than drilling jigs.

Offline Gregor

  • Posts: 982
Re: Lr32 system and rail
« Reply #3 on: July 07, 2018, 02:51 AM »
After an initial learning curve (to wrap your head around the different options on how to align it to your workpiece) the LR32 is quick to use and relieable in giving repeatable results.

Can also be easily extended to other uses: get a 20mm cutter to make your own MFT tops, as-is as a story stick with a 32mm grid (for other tools, like a domino), route hidden (end(s) closed) grooves/dados/rebates/slots (limiting the sled movement with anti kickback stops for the TS, or an anything else that goes into the t-slot and can be locked in place, in case you need to go out of the 32mm grid the holey rail provides), ...
« Last Edit: July 07, 2018, 02:54 AM by Gregor »

Offline SoonerFan

  • Posts: 402
Re: Lr32 system and rail
« Reply #4 on: July 11, 2018, 09:21 PM »
I have an LR32 and as others have stated, there is a learning curve.  But once you get it figured out it is great.  I made a large built in book case for my niece that she uses as a pantry.  For that project is was simply fantastic for drilling the shelf pin holes. 

For me it’s not an “every project tool” but when I need it I am glad I own it.

Offline Joe Felchlin

  • Posts: 138
  • Just another day in paradise - Livin’ the dream!
Re: Lr32 system and rail
« Reply #5 on: July 11, 2018, 10:02 PM »
Another vote for Festool’s LR32 System...
Worth the investment - Especially if you’re making more than 1-2 cabinets.
As said, there is a learning curve... But it’s interesting... And not too “steep”.
I use it and my OF 1400 router to make cabinets.
Extremely accurate. Repeatable. And quick... Once you get the system down.

erock’s (Eric’s) LR32, 7 part, step by step, “how to” series -
Is worth every minute it takes to watch it. (Me... more than once. [embarassed])
http://festoolownersgroup.com/festool-how-to/a-lr32-video/

« Last Edit: July 11, 2018, 10:11 PM by Joe Felchlin »
FESTOOL: CT26 and CT33 E HEPA Dust Extractors, MFT 1080, MFT-3, TS 55 REQ-F-Plus USA, TS75 EQ, Guide Rails: 1080's/1400/3000mm, LR 32-SYS/Holey Rail, Parallel Guides and Extensions, OF1400 EQ Plunge Router, OF1010 EQ Plunge Router, HL 850 Planer, RO125 FEQ Rotex Sander, LS 130 EQ Linear Detail Sander, DX93E Detail Sander, C12 Cordless Drill, CXS Cordless Compact Drill Driver, SYS-Centrotec-Set, Domino XL DF 700 EQ Plus Tenon Joiner Set, Domino DF 500 Tenon Joiner | WOODPECKERS: DF 500 Offset Base System | BOSCH: 5412L Compound Miter Saw, 4100-09 10-Inch Table Saw | POWERMATIC: 60HH 8" Jointer, PWBS 14" Bandsaw w/Riser Block | MAKITA: 2012NB Bench Top Planer | JESSEM: Mast-R-Lift XL/Fence/Slide, Rout-R-Plate/Table Stand | RIKON: 50-120 6inX48in Belt-Disc Sander | JET: JBOS-5 Benchtop Oscillating Spindle Sander | PORTER CABLE: 7518 and 690LVRS Routers, 557 Pro Plate Joiner, 16/18/23 Gauge Nailers | LEIGH JIGS: D4R 24 Pro Dovetail Jig, FMT Pro Mortise & Tenon Jig | LIE-NIELSEN: Almost every hand plane | DOWELMAX: 3/8" and 1/4" | KREG: K3 Master System | FEIN: Multimaster FMM 250 Q Kit | TORMEK: Super-Grind 2000 | DUST DEPUTY: Industrial (ALL) Steel Deluxe Cyclone (2)

Offline jobsworth

  • Posts: 5242
  • Does Anyone Know What Time It Is?
Re: Lr32 system and rail
« Reply #6 on: July 12, 2018, 01:03 PM »
Ive had the LR 32 system for a while. I think its a great system.

Doing one or two cabinets does take some time. But when I do a lot of cabinets say 3 + it really shines.

You do have to be accurate in cutting your cabinet sides. They have to be dead nuts on 32mm. They can be a tad shorter and use a small filler piece to take up the slack. Be sure to mark which is the top when using a filler. Otherwise the holes wont match.

Offline Peter Halle

  • Global Moderator
  • *
  • Posts: 11533
Re: Lr32 system and rail
« Reply #7 on: July 12, 2018, 04:31 PM »
I used mine last weekend.  I rarely use it, so when I do I have to watch a video to remind me of the things that I forgot.  I got that Zen feeling when the holes were so pretty and perfect  [big grin].  It is a step up from the cheaper offerings from other manufacturers but is a step below multi spindle boring machines.

Peter

Offline Kodi Crescent

  • Posts: 711
Re: Lr32 system and rail
« Reply #8 on: October 01, 2018, 10:52 PM »
With regards to the n*32mm length requirement for rail placement - I thought of trying threaded dogs such as rail dogs or some other short dogs to center rails on workpieces that aren't cut into 32mm increments.  While this sounds good in theory, I haven't tried this yet, so I don't know how well it works in reality.