Author Topic: Abrasives search tool - find the right abrasive for your sander and sanding task  (Read 42207 times)

0 Members and 1 Guest are viewing this topic.

Offline Festool USA

  • Festool USA Employee
    FOG Administrator
  • *
  • Posts: 8232
    • Festool USA
I have added a search tool to our website that will allow you to select your sander model, application and optionally preferred grit range. The website will then display abrasives that match your search criteria.

I hope you all find this useful.

http://www.festoolusa.com/abrasives

Shane

Festool USA does not pre-approve the contents of this website nor endorse the application or use of any Festool product in any way other than in the manner described in the Festool Instruction Manual. To reduce the risk of serious injury and/or damage to your Festool product, always read, understand and follow all warnings and instructions in your Festool product's Instruction Manual. Although Festool strives for accuracy in the website material, the website may contain inaccuracies. Festool makes no representations about the accuracy, reliability, completeness or timeliness of the material on this website or about the results to be obtained from using the website. Festool and its affiliates cannot be responsible for improper postings or your reliance on the website's material. Your use of any material contained on this website is entirely at your own risk. The content contained on this site is provided for informational purposes only and does not constitute professional advice.


Offline Bob Marino

  • Festool Dealer
  • *
  • Posts: 2748
    • bobmarinosbesttools.com
Very helpful. Well done.

Thanks.

Bob
Festool  Dealer since 2002; user well before that!
            http://bobmarinosbesttools.com
                   Service As It Should Be

Offline Sean Ackerman

  • Festool Dealer
  • *
  • Posts: 1634
  • Festool Dealer near NYC - 10,000 sq feet!
    • Festoolproducts.com
You are the man.  Awesome stuff.
Buy Festool Online" class="bbc_img

Offline neilc

  • Posts: 1958
Nice addition, Shane!  Thank you.

Do you have application recommendations for Stone or Metal?

 I did not see them in the options and know there have been questions on FOG in the past about both of them.  I've used Granat on limestone in the past with great results.

neil

Offline Festool USA

  • Festool USA Employee
    FOG Administrator
  • *
  • Posts: 8232
    • Festool USA
Do you have application recommendations for Stone or Metal?

Neil,

We do have stainless steel and non-ferrous metals as an option.

Stone is not listed (yet), but I will see about adding it.

The purpose is to cover the top 95% of applications. There will still be some tasks that are too specific to cover everything, I'm sure.

Shane

Offline JimRay

  • Posts: 97
Super job, Shane! Well organized and easy to use.

Jim
Jim Ray

Offline Festool USA

  • Festool USA Employee
    FOG Administrator
  • *
  • Posts: 8232
    • Festool USA
Super job, Shane! Well organized and easy to use.

Thanks, Jim. Almost a throw back to the old Select-A-Screw.  [smile]

Offline RDMuller

  • Festool Dealer
  • *
  • Posts: 235
Nice!!!!
Any chance of converting it to a smart phone app??

Offline NYC Tiny Shop

  • Posts: 932
    • jamesfinndesign.com
Great service! A page to bookmark! Thanks!

Offline gkaiseril

  • Posts: 329
Nice!!!!
Any chance of converting it to a smart phone app??

Works great with Opera, FireFox, Chrome,, and the provided web browser on a Samsung S3. But this requries an internet connection.

Shane,

Very nice.
George Kaiser

TS 55 REQ, RO 90, RO 150, CT 26, PSB 420, MFT/3

Offline dicktill

  • Posts: 232
VERY nice Shane, thanks a bunch! I'm sure a lot of work went into this already, but one request: When multiple abrasives such as Rubin, Granat, Brilliant, and Cristal all show up, say for the ETS 150 for sanding bare wood, could you have some sort of "1st choice, 2nd choice, etc."?

Regards, Dick

Offline Festool USA

  • Festool USA Employee
    FOG Administrator
  • *
  • Posts: 8232
    • Festool USA
Dick, maybe I need to make it clearer, but they are in order of recommendation.

Offline dicktill

  • Posts: 232
Dick, maybe I need to make it clearer, but they are in order of recommendation.

I was wondering if that was the case, but it didn't "hit me upside the head". Thanks again!

Offline gnlman

  • Posts: 112
Sandpaper for dummies(j/k)....perfect for me....thank you very much, a great tool to make our choices easier....especially for us non pro's...that would be me.....

Greg

Offline TelcoRandy

  • Posts: 230
Finally something that isn't NAINA!
I'm an abrasives newbie so I'll definitely check it out.

Thanks Shane!

Offline JimRay

  • Posts: 97
Thanks, Jim. Almost a throw back to the old Select-A-Screw.  [smile]

Embarrassed to say that Select-a-Screw never worked as well as this new "Select-an-Abrasive"

Jim
Jim Ray

Offline Chip S.

  • Festool Dealer
  • *
  • Posts: 31
    • FestoolNirvana.com
Awesome. Super-useful.

Chip
http://www.FestoolNirvana.com  |  1-844-FESTOOL

Offline SRSemenza

  • Global Moderator
  • *
  • Posts: 7273
  • Finger Lakes Region, NY State , USA
I like that it places the results in order of best for the task.

Seth

Offline Festool USA

  • Festool USA Employee
    FOG Administrator
  • *
  • Posts: 8232
    • Festool USA
Added backing pads to the search results to make it easy to see what pad(s) are available for your sander.  [thumbs up]

Offline grbmds

  • Posts: 1516
Is there a significant difference in results or paper life between Granat and Rubin for prepping bare wood for staining and/or finishing? In my one use of the 125 I thought the results were great with the Granat I bought as a set with the sander.
Randy

Offline Festool USA

  • Festool USA Employee
    FOG Administrator
  • *
  • Posts: 8232
    • Festool USA
Is there a significant difference in results or paper life between Granat and Rubin for prepping bare wood for staining and/or finishing? In my one use of the 125 I thought the results were great with the Granat I bought as a set with the sander.

No, for bare wood, the results and paper life will be very similar. You will save slightly on price with Rubin.

Offline Gerald_D

  • Posts: 207
Thanks Shane- appreciate the efforts in creating this!  I will be using this frequently (and also very soon as I have a new DTS400 on the way).

Regards,
Gerald
Gerald
I have Festools- Big and Small and a few other tools

Offline mheffernan

  • Posts: 20
    • MDH Woodworking
Thanks for the link. Very helpful.
Michael Heffernan
MDH Woodworking

Offline Tinker

  • Posts: 3412
This is great, Shane.
I am slowly getting to bottoms of piles of discs I bought many moons ago and renewing as i go.
Your hard work will make my work so much simpler and much easier.
Thanks
Tinker
Wayne H. Tinker

Offline Cabenth

  • Posts: 12
Re: Abrasives search tool - RO90 'sample pack' contents
« Reply #24 on: October 17, 2014, 07:20 AM »
Didn't know where best to put this question so here it is...

I just received my RO90. It is advertised to come with an abrasive 'sample pack' but I only see 2 pieces, both the blue, course grit, one for the delta, one for the round. What is supposed to be in that pack, and are the sheets just tossed in the systainer, not wrapped in a bag or anything?

All the product images indicate 6 pieces, 1 blue and 2 white for both round and delta.
If what I got was correct, why bother?

While we're on the subject, it would be nice if Festool offered an abrasive progression pack, maybe 7 sheets each of 60, 100, 150, 220, 320, 500, and 1k. That's one piece less than your 50 sheet packs, but far more useful for someone who doesn't have a floor to sand (in my opinion).

Thanks for your help

Offline mike_aa

  • Posts: 906
Cabenth,

If you need a small assortment of abrasives for the RO90 or any sander, Tom Bellemare at Tool Home will gladly make one up for you in the quantities you need for each grit.  He helped me with my RO90 and other sanders I have.  In fact, as soon as I recover from this Recon sale I'll be calling him myself to get one for the recon RS2 I got.

Mike A.
« Last Edit: October 17, 2014, 09:17 AM by mike_aa »

Offline Tom Bellemare

  • Inactive Member
  • *
  • Posts: 5148
  • Festool demo's & personal service in Central Texas
    • Tool Home LLC
Re: Abrasives search tool - RO90 'sample pack' contents
« Reply #26 on: October 17, 2014, 10:00 AM »
Didn't know where best to put this question so here it is...

I just received my RO90. It is advertised to come with an abrasive 'sample pack' but I only see 2 pieces, both the blue, course grit, one for the delta, one for the round. What is supposed to be in that pack, and are the sheets just tossed in the systainer, not wrapped in a bag or anything?

All the product images indicate 6 pieces, 1 blue and 2 white for both round and delta.
If what I got was correct, why bother?

While we're on the subject, it would be nice if Festool offered an abrasive progression pack, maybe 7 sheets each of 60, 100, 150, 220, 320, 500, and 1k. That's one piece less than your 50 sheet packs, but far more useful for someone who doesn't have a floor to sand (in my opinion).

Thanks for your help


When the RO 90 first came to North America, it included very generous abrasive packs in both configurations. For quite some time now, it has only had one sheet of Granat in each configuration.


Tom
Tom Bellemare
Customer Svc
Tool Home LLC
www.tool-home.com
512-428-9140

Offline Cabenth

  • Posts: 12
Thanks Tom.

One area where Festool sorely lacks... 2 pieces of paper isn't a 'pack' and it's not even a sample since there's only the one kind of the one grit. At best, it's 'starter paper.' Just enough to be able to make sure the device works. Maybe they should call it 'Proof of Function Abrasive.' (POFA) that's all it is. Suppose the bosses tissue is they advertise a pack, show a picture that should get you started, but I could not find any place where it actually laid out what was in the box.

Offline grbmds

  • Posts: 1516
I don't remember every buying a sander (and I own older sanders from Makita, Rockwell (really old), and Dewalt) that included any sandpaper. I wouldn't even expect it.
Randy

Offline rst

  • Posts: 1251
Bob Marino sells many grits in 10 packs.  Bob is GREAT!!

Offline Cabenth

  • Posts: 12
I don't remember every buying a sander (and I own older sanders from Makita, Rockwell (really old), and Dewalt) that included any sandpaper. I wouldn't even expect it.

I wouldn't expect it either, of a $75 to $150 sander, but the RO90 is a BIT more than that, I feel it's reasonable to expect a little more, perhaps 1 each of a progression, 10 total.

Festool USA does not pre-approve the contents of this website nor endorse the application or use of any Festool product in any way other than in the manner described in the Festool Instruction Manual. To reduce the risk of serious injury and/or damage to your Festool product, always read, understand and follow all warnings and instructions in your Festool product's Instruction Manual. Although Festool strives for accuracy in the website material, the website may contain inaccuracies. Festool makes no representations about the accuracy, reliability, completeness or timeliness of the material on this website or about the results to be obtained from using the website. Festool and its affiliates cannot be responsible for improper postings or your reliance on the website's material. Your use of any material contained on this website is entirely at your own risk. The content contained on this site is provided for informational purposes only and does not constitute professional advice.


Offline Tinker

  • Posts: 3412
When i started wit my first Festoy sander, i got several different grits in progression starting with 80 grit up to 180.  The problem i discovered was that i did not get the progression in one type, such as Rubin.  Each step up was a different type and I was running into somewhat non satisfaction with my progressions, especially in the lower grades.

By the time i was wearing out packages (I got everything for the 150 in 5 and 10 packs.), I was beginning to understand a little more about what each grade and grit was good for.  My biggest problem was with Rubin.  That seemed to not cut wood as well as elected in the lower grits and it did not seem to last as long as i had hoped.  Once i found grant, I discovered that the RO 150 was a much better sander that i had even dreamed of.  I now have Granat in grits starting at 40, progressing by steps 0f 20 grits up to 100. 

In the past, i found I used a lot more paper in the lower grits as I was sort of getting inpatient until I got to the higher grits.  I now go thru the steps with Granat in much less time, far less impatience and a disc seems to last forever.  By the time i get to the higher grits, I am even using less paper there as the ground work has gone a lot smoother.  I am able to use up my old stocks of Rubin with better results.

I am currently working on a serving tray for THE BOSS while she is away on other side of the big pond.  I sanded the whole tray starting with 60 grit Grant.  actually, i started with 60 grit Rubin and was starting to get impatient.  I was only doing the sides and using the Festoy sanding block that is configured to use a full 150 disc.  I was trying to get rid of saw marks. I had used Bandsaw to rip two of the sides.  They were dead on straight, but with tooth marks. I finally changed over to a disc of Granat 60 and wow! what a difference.  I had intended to use my LS 130, but those marks disappeared so fast doing by hand, i never did take the 130 out of its systainer. Once those tooth marks were gone, the higher grits were easy and fast no matter which type of paper I used.
Tinker
Wayne H. Tinker

Offline SPM in King

  • Posts: 6
Shane,

I sand a lot of domestic hardwood table tops.  I have had luck with Rubin, but a am slowly moving to Garnat.  When purchased in bulk, the price differential is minimal.

I often fill areas with epoxy mixed with wood dust.  Both the above papers clog quiet rapidly when used at high speed, so I have been turning the speed all the way down to extend the life of the disk.  I typically use 80 or 120 grit for this.  Is there a better disk for this application?

Thanks.
Steve

TS 75 EQ, RO 150 FEQ

Offline SRSemenza

  • Global Moderator
  • *
  • Posts: 7273
  • Finger Lakes Region, NY State , USA
Shane,

I sand a lot of domestic hardwood table tops.  I have had luck with Rubin, but a am slowly moving to Garnat.  When purchased in bulk, the price differential is minimal.

I often fill areas with epoxy mixed with wood dust.  Both the above papers clog quiet rapidly when used at high speed, so I have been turning the speed all the way down to extend the life of the disk.  I typically use 80 or 120 grit for this.  Is there a better disk for this application?

Thanks.

Hi,

   Welcome to the forum!  [smile]

      How has turning the speed down worked out? I have not sanded epoxy, but my guess is that Granat will be the best choice.  Although if you can get your hands on some of the discontinued Cristal I would try that. It has a sparse grit distribution that allows more space between particles. It resists clogging on potentially gummy stuff quite well. I would slow the speed for Cristal as well. Also keeping the sander moving , regardless of abrasive , will help prevent the material from heating up and getting soft.  Check in stores and with dealers, and Ebay for some Cristal. Somebody might still have some.

Seth

Offline SPM in King

  • Posts: 6
Seth, slowing down helps, but ultimately epoxy is nasty stuff to sand.  Cleaning the disk with a crepe block before the epoxy starts to gum up also helps.  Once it actually melts, the disk is finished.  I will try to move around a bit more.  I can see how that would help/  We don't have a lot of dealers up in the frozen north, but I will look for some Cristal.

Thanks for the reply.
Steve

TS 75 EQ, RO 150 FEQ

Offline Samtor

  • Posts: 16
I have added a search tool to our website that will allow you to select your sander model, application and optionally preferred grit range. The website will then display abrasives that match your search criteria.

I hope you all find this useful.

http://www.festoolusa.com/abrasives

Shane

Hi Shane,
There seems to be 2 similar grits with different part numbers for Platin.

RO 90 DX (Round) Sander   S500   Super Fine   15   90 mm Diameter   Round   497426   -
RO 90 DX (Round) Sander   S500   Super Fine   15   90 mm Diameter   Round   498322   -
RO 90 DX (Round) Sander   S1000   Super Fine   15   90 mm Diameter   Round   497427   -
RO 90 DX (Round) Sander   S1000   Super Fine   15   90 mm Diameter   Round   498323   -

The official Festool website also has the similar issue but it lists the diameters as 80mm.

Could you help clarify.
Thanks.

Offline Zoofish

  • Posts: 4
When i started wit my first Festoy sander, i got several different grits in progression starting with 80 grit up to 180.  The problem i discovered was that i did not get the progression in one type, such as Rubin.  Each step up was a different type and I was running into somewhat non satisfaction with my progressions, especially in the lower grades.

By the time i was wearing out packages (I got everything for the 150 in 5 and 10 packs.), I was beginning to understand a little more about what each grade and grit was good for.  My biggest problem was with Rubin.  That seemed to not cut wood as well as elected in the lower grits and it did not seem to last as long as i had hoped.  Once i found grant, I discovered that the RO 150 was a much better sander that i had even dreamed of.  I now have Granat in grits starting at 40, progressing by steps 0f 20 grits up to 100. 

In the past, i found I used a lot more paper in the lower grits as I was sort of getting inpatient until I got to the higher grits.  I now go thru the steps with Granat in much less time, far less impatience and a disc seems to last forever.  By the time i get to the higher grits, I am even using less paper there as the ground work has gone a lot smoother.  I am able to use up my old stocks of Rubin with better results.

I am currently working on a serving tray for THE BOSS while she is away on other side of the big pond.  I sanded the whole tray starting with 60 grit Grant.  actually, i started with 60 grit Rubin and was starting to get impatient.  I was only doing the sides and using the Festoy sanding block that is configured to use a full 150 disc.  I was trying to get rid of saw marks. I had used Bandsaw to rip two of the sides.  They were dead on straight, but with tooth marks. I finally changed over to a disc of Granat 60 and wow! what a difference.  I had intended to use my LS 130, but those marks disappeared so fast doing by hand, i never did take the 130 out of its systainer. Once those tooth marks were gone, the higher grits were easy and fast no matter which type of paper I used.
Tinker
I've used Granat on limestone in the past with great results.




nexus 9 hülle
« Last Edit: January 10, 2015, 01:05 AM by Zoofish »

Offline Tinker

  • Posts: 3412
Do you use a CT when sanding(grinding?) limestone?
Does the dust clog your HEPA filters (if you have them on your model)
Tinker
Wayne H. Tinker

Offline Tom Bellemare

  • Inactive Member
  • *
  • Posts: 5148
  • Festool demo's & personal service in Central Texas
    • Tool Home LLC
Tinker:

I've used a Rotex 150 with Saphir for shaping and taking out saw marks on landscaping limestone slabs. It works great. Prior to Granat being available, I then switched to Rubin, just because I had a bunch of it, and went through the grits to about 120. At about 80, the fossils start to become really noticeable. At 120, they are quite prominent and it starts to feel silky.

I've always stopped there and sealed with teflon impregnated sealer. The next time, I think I'll try going to about 180 and see what I was missing... I'm also going to use Granat after the shaping.

I haven't used a CT yet - I just did it outside. Next time, I'll try dust extraction. I seriously doubt it will get past the bag (5 microns).


Tom
Tom Bellemare
Customer Svc
Tool Home LLC
www.tool-home.com
512-428-9140

Offline Tinker

  • Posts: 3412
Tom, I wish I had known about Festoys when i was in MasonBiz.  Especially the sanders and CT's.  We used hammers & wedges to split stones.  Hammers and chisels to dimension. Also Grinders and carborundum blades on circular saws to cut to dimension and shape.  But no DC.  Just good face masks and goggles. A lot of guys used NO face (nose & eye) protection.  Polishing I had done in a shop where I bought my stone already dimensioned to specifications.

I did find lots of sedimentary type stones in the field (excavated as well as gathered from stone walls) with fossils imbedded. I am sure when you sanded around those fossils, you did not sand down into the depressions, but only the flat areas around the imprints if you wanted to save.  Some fossils could be quite graphic showing even the tiniest details in the stone. 

Even tho i no longer even THINK of cutting (or even lifting) stones, i am still interested in the methods used, especially the methods used since i quit the biz around 35 years ago.  there are a lot of new ideas and materials that have come along since '81 that used to be handled at quarries and supply shops.  Some of those, such as your polishing on site are now somewhat routine out in the field.

Tinker
Wayne H. Tinker

Offline jofuss55

  • Festool Dealer
  • *
  • Posts: 8
You know,Shane, this is very helpful and I wished that you had included it in the catalog. The last two revisions have seen the removal of items that should be there!
Just because a dealer is  deemed a woodworking outlet/retailer doesn't mean that the local painters don't call on them for abrasives, or the local metal workers or polishers for that matter. It hurts sales when valued customers can't get all the info from their local dealer.
Maybe this version of the catalog will be more inclusive, I hope so.

Offline Tinker

  • Posts: 3412
You know,Shane, this is very helpful and I wished that you had included it in the catalog. The last two revisions have seen the removal of items that should be there!
Just because a dealer is  deemed a woodworking outlet/retailer doesn't mean that the local painters don't call on them for abrasives, or the local metal workers or polishers for that matter. It hurts sales when valued customers can't get all the info from their local dealer.
Maybe this version of the catalog will be more inclusive, I hope so.

Maybe a page with recommendations of best to use for various trades.  Even tho i no longer play with brick and stone, i still get asked about materials and methods quite often.  Others above, like jofuss55, have mentioned uses other than for wood, to use Festoy sanders and papers.

I have been amazed to have found thru several threads that Festool sanders have been used for concrete and stone.  My first reaction to the earliest questions concerning those materials has been to not even waste one's time (words to that effect).  I am slowly learning that such work can be done.  That was unheard of back when i was 38...

I still am not inclined to think of Festool sanders and discs as even a second choice for stone and concrete.  I am learning.  Actually, I learned to stay away from that work many moons ago  ::)
Tinker
Wayne H. Tinker

Offline powertoolss

  • Posts: 3
    • Circular Saw Hub
Great to find your post. Thank you

Offline ccat70541

  • Posts: 1
Useful very well made . Thank you  [big grin] [big grin] [big grin] [big grin]
ติดตามบล็อกเกมสนุกมันส์ๆได้ที่นี่
การพนันออนไลน์
เดิมพันบอลออนไลน์
เล่นคาสิโนออนไลน์

Offline VW MICK

  • Posts: 751
yes

I found this very helpful in fact a Bit too helpful

it just relieved me of about £200 lol just couldn't decide what to get

Offline Foghat

  • Posts: 37
Thanks so much, this is exactlywhat I was looking for to help with several projects, and knowing where to start.
Saves lots of time and let's me get a much better idea of what to do.
Again, Thank you!

Offline ckurak

  • Posts: 1
I have been using Brilliant 2 P220 (496592) for years with my ETS150 for bare wood sanding just prior to spray painting. I ran out and am trying to order more. Your website app says this is the correct part number. But, everywhere I look it shows as "out of stock" or "Discontinued." Is this really true? And, if so, what is the replacement?

Thanks!

Offline Shane Holland

  • Festool Dealer
  • *
  • Posts: 9734
    • The Tool Nut's Festool Store
@ckurak welcome to the forum. Yes Brilliant has been discontinued. Granat is the best replacement choice.
Buy Festool Online" class="bbc_img
Fast, Free Shipping - Festool Trained Experts - Unparalleled Customer Service - No Sales Tax Collected (Outside NY/VA)
30 Minutes from NYC - 10,000 Square Foot Showroom / 2,000 Square Foot Festool Showroom
Toolnut.com and FestoolProducts.com

Offline McNally Family

  • Posts: 318
  • Festool Atomic Phaser Particle Blaster (APPB Set)
I have been using Brilliant 2 P220 (496592) for years with my ETS150 for bare wood sanding just prior to spray painting. I ran out and am trying to order more. Your website app says this is the correct part number. But, everywhere I look it shows as "out of stock" or "Discontinued." Is this really true? And, if so, what is the replacement?

Thanks!

I purchased a bunch of Brilliant2 from Tool Nut (Festool products.com), several months ago when it was on clearance sale.  You might try Bob Marino, or even Amazon.com.

Here is a link I found for 180 grit Brilliant2 150 in a quick google search, although the price seems a little high for a discontinued product.  It will be harder to find what you need, but there are many dealers in the United States, and I'm sure someone has what you need (and if your lucky, it will be at a clearance price).

http://hardwarespot.com/brillant-2-p180-abrasive-6-dia-100-pack-by-festool-496591.html?gclid=CjwKEAjwydK_BRDK34GenvLB61YSJACZ8da36AZ0QjWkOsPWtY52udNn-5CQxJblS6YfufjR6cjCfBoCmBnw_wcB
GREEN: In order of purchase = C18 5.2 Set w/Centrotec Installer's Set | CT26 w/Installer Cleaning Set | CT Wings | SYS-MFT | RS 2 E | Hose w/ Sleeve 3.5m | metric+imperial ZOBO bit sets | Centrotec Stubby Brad Point Bit Set 3-8mm |  HSS D3-10 CE/10x Metric Twist Drill Bit Set | 115mm X 226mm Hand Sanding Block | 80mm X 133mm Hand Sanding Block | HSK D21.5 5m hose | CT Boom Arm Bundle Set |  Won the CXS Li 2.6 90 Limited Edition on 06/20/2016 | Metric Parallel Guide Set | 1080 Plate for custom MFT | Clamping ElemenTS (1) | Quick Clamps For MFT (2) | Festool 300mm Screw Clamps set (1) | Festool 120mm Screw Clamps set (1) | Next  Purchase: Something else Metric |

RED: In order of purchase = Mafell P1cc w/tilting base | Complete range of Mafell blades | Collins Coping Foot |  F 160 (x1)+F 110 (x1)+F 80 (x1) w/Guide pocket, clamps & Connector (x1)  | Angle fence F-WA | Next Purchase :  TBD