« previous next »
Pages: 1 [2]  All   Go Down

Author Topic: Festool Centrotec Installers Set(s) - Reference Thread  (Read 25267 times)

0 Members and 1 Guest are viewing this topic.

Offline tjbnwi

  • Posts: 5733
  • Cedar Tucky Indiana
Re: Festool Centrotec Installers Set(s) - Reference Thread
« Reply #30 on: September 19, 2017, 08:59 AM »
Quote from: Naildrivingman on August 20, 2017, 06:42 AM
I just bought the centrotec stubby drill bits yesterday. I don't have an immediate use for them, but I know when I do they will be invaluable. For now they reside in my installers case and I will simply admire them for their cuteness!

SIDE NOTE:  What is the rationale behind a $90 USD FT centering  bit?  For that price I hope it not only drill centered holes, but also mortises the hinges and installs them!  I have 3 Vix (#5,7,9) bits that cover all my needs and I think they were $10-15 each.  Just curious.

The self center from Festool is a 5mm. I use mine for the occasional draw slide into a case that does not have holes.

It's also great for drilling near door and drawer edges for stem bumpers.

Tom
Logged
Festool USA does not pre-approve the contents of this website nor endorse the application or use of any Festool product in any way other than in the manner described in the Festool Instruction Manual. To reduce the risk of serious injury and/or damage to your Festool product, always read, understand and follow all warnings and instructions in your Festool product's Instruction Manual. Although Festool strives for accuracy in the website material, the website may contain inaccuracies. Festool makes no representations about the accuracy, reliability, completeness or timeliness of the material on this website or about the results to be obtained from using the website. Festool and its affiliates cannot be responsible for improper postings or your reliance on the website's material. Your use of any material contained on this website is entirely at your own risk. The content contained on this site is provided for informational purposes only and does not constitute professional advice.

Offline jobsworth

  • Posts: 5271
  • Does Anyone Know What Time It Is?
Re: Festool Centrotec Installers Set(s) - Reference Thread
« Reply #31 on: March 07, 2018, 12:28 AM »
I have the 2013 Installers set. It didnt come with the countersinks or 5 mm self centering bits and the standard (flat tip) screw driver bits. All that i had buy extra.It did come with the stubby drill bits.

I use the 5mm but for installing drawer slides. I like useing the blum hinges. So it comes in handy.
« Last Edit: March 28, 2018, 04:49 PM by jobsworth »
Logged

Offline Alanbach

  • Posts: 168
Re: Festool Centrotec Installers Set(s) - Reference Thread
« Reply #32 on: April 22, 2018, 01:02 AM »
I am curious as to approximate price of these sets. I realize that they are all a little different and some of them where purchased in 2013 or before. I just saw something on Amazon that almost $1,000. Is that about right?
Logged

Offline Samo

  • Posts: 554
Re: Festool Centrotec Installers Set(s) - Reference Thread
« Reply #33 on: April 22, 2018, 01:09 AM »
No  [eek]
Logged

Offline Alanbach

  • Posts: 168
Re: Festool Centrotec Installers Set(s) - Reference Thread
« Reply #34 on: April 22, 2018, 01:10 AM »
What should they cost?
Logged

Offline ScotF

  • Posts: 2503
Re: Festool Centrotec Installers Set(s) - Reference Thread
« Reply #35 on: April 22, 2018, 01:15 AM »
Quote from: Alanbach on April 22, 2018, 01:10 AM
What should they cost?

1/2 that price
Logged

Offline Alanbach

  • Posts: 168
Re: Festool Centrotec Installers Set(s) - Reference Thread
« Reply #36 on: April 22, 2018, 01:21 AM »
Thanks!
Logged

Offline Ben63

  • Posts: 7
Re: Festool Centrotec Installers Set(s) - Reference Thread
« Reply #37 on: November 10, 2018, 11:03 AM »
I think this is the first centrotec set. Bought it for about 15-20 years ago.
« Last Edit: November 10, 2018, 02:45 PM by Ben63 »
Logged

Offline six-point socket II

  • Posts: 743
  • aka @the_black_tie_diyer
Re: Festool Centrotec Installers Set(s) - Reference Thread
« Reply #38 on: November 10, 2018, 01:00 PM »
Thanks for sharing! :)

Kind regards,
Oliver
Logged
Kind regards,
Oliver
Pages: 1 [2]  All   Go Up
« previous next »