Author Topic: MFK 700 With 0 Degree, 1.5 Degree Bases & edge guide in Systainer  (Read 768 times)

0 Members and 1 Guest are viewing this topic.

Offline ScotF

  • Posts: 2437
Not sure if this has been posted, but I know that it has been discussed - I found a way to get everything into the Systainer for this router - you do have to unscrew the knob on the 0 degree base and lower the router to be flush with the vertical base, but it works! It is a tight fit - also, I put all my instructions under the insert in the bottom of the Systainer so I have them, but they are out of the way.

Here is a picture if anyone needs it...so far this has worked well. Not any other room, but at least all the bases are with the machine.


Festool USA does not pre-approve the contents of this website nor endorse the application or use of any Festool product in any way other than in the manner described in the Festool Instruction Manual. To reduce the risk of serious injury and/or damage to your Festool product, always read, understand and follow all warnings and instructions in your Festool product's Instruction Manual. Although Festool strives for accuracy in the website material, the website may contain inaccuracies. Festool makes no representations about the accuracy, reliability, completeness or timeliness of the material on this website or about the results to be obtained from using the website. Festool and its affiliates cannot be responsible for improper postings or your reliance on the website's material. Your use of any material contained on this website is entirely at your own risk. The content contained on this site is provided for informational purposes only and does not constitute professional advice.


Offline live4ever

  • Posts: 739
Re: MFK 700 With 0 Degree, 1.5 Degree Bases & edge guide in Systainer
« Reply #1 on: March 05, 2018, 03:06 PM »
Nice.

I also figured out a way to do this - will take a look and see if I ended up doing the same arrangement.
Current systainer to productivity ratio:  very high

Offline ben_r_

  • Posts: 1004
Re: MFK 700 With 0 Degree, 1.5 Degree Bases & edge guide in Systainer
« Reply #2 on: March 05, 2018, 04:23 PM »
Nicely done!
If at first you don't succeed, redefine success!

Offline rst

  • Posts: 1808
Re: MFK 700 With 0 Degree, 1.5 Degree Bases & edge guide in Systainer
« Reply #3 on: March 05, 2018, 06:18 PM »
I transferred mine into a Sys Combi II.  This lets me keep the various parts and accessories together.  Did the same with my 1010 and my various drills.

Offline ScotF

  • Posts: 2437
Re: MFK 700 With 0 Degree, 1.5 Degree Bases & edge guide in Systainer
« Reply #4 on: March 05, 2018, 08:15 PM »
I transferred mine into a Sys Combi II.  This lets me keep the various parts and accessories together.  Did the same with my 1010 and my various drills.

Yeah - I have thought about doing that for a few tools - makes a ton of sense - especially if they offered the attic lids as well on everything.

Offline rst

  • Posts: 1808
Re: MFK 700 With 0 Degree, 1.5 Degree Bases & edge guide in Systainer
« Reply #5 on: March 06, 2018, 07:12 AM »
I have five of the attic lids that I purchased from Lee Valley Tanos, they were not separate unfortunately, but I used the Sys for other tools and supplies.  I believe Toolnut/Festolproducts now sells them as a separate item.  I've switched the lids to various other systainers depending upon need.  I have one on the Sys that my Fein Supercut lives in to hold blades, one two on drill Sys, and one for my Sys V that holds my Senco compressor.