Author Topic: MFT squaring  (Read 1570 times)

0 Members and 1 Guest are viewing this topic.

Offline Master Carpenter

  • Posts: 90
MFT squaring
« on: February 06, 2018, 12:24 PM »
How often is everyone checking their MFT guiderail for square? How often are you finding it needs adjustment?

I've had my MFT for 8 years and have never had to adjust the factory set stops, they've always been dead on. I pull a diagonal measurement every once in a while across panels coming off the table and they always seem good. My cabinets always come out square.

I seem to come across a lot of methods and tools for squaring the MFT, is it all a bunch of drama created to make us worry/spend money on a nonissue?
Ts 55, Ts 75, of 1010, lr 32, mft, mfs 700, RO 150 x2 + paper asort, RO 90 + paper asort, pro 5, df 500 + dom asort, hl 850 e, ti 15, t18, cxs, centrotec set, ct48, ct sys, vac sys, 32;55x2;118 tracks, a stack of sys and an og festool first aid kit. Kapex, planex, carvex, conturo.

Festool USA does not pre-approve the contents of this website nor endorse the application or use of any Festool product in any way other than in the manner described in the Festool Instruction Manual. To reduce the risk of serious injury and/or damage to your Festool product, always read, understand and follow all warnings and instructions in your Festool product's Instruction Manual. Although Festool strives for accuracy in the website material, the website may contain inaccuracies. Festool makes no representations about the accuracy, reliability, completeness or timeliness of the material on this website or about the results to be obtained from using the website. Festool and its affiliates cannot be responsible for improper postings or your reliance on the website's material. Your use of any material contained on this website is entirely at your own risk. The content contained on this site is provided for informational purposes only and does not constitute professional advice.


Offline Sparktrician

  • Posts: 3634
Re: MFT squaring
« Reply #1 on: February 06, 2018, 01:15 PM »
I check mine at least once per day, but seldom have to adjust it.  There have been several threads on the "how to" aspects; one recently.  If you only cut one thickness of material, it will rarely go out of square, but if you change thicknesses frequently or square it low, then raise the rail, there is a much greater likelihood that it will go out of square, just from raising or lowering it. 
« Last Edit: February 06, 2018, 01:18 PM by Sparktrician »
- Willy -

 "Remember, a chip on the shoulder is a sure sign of wood higher up." - Brigham Young

Offline duc996

  • Posts: 154
Re: MFT squaring
« Reply #2 on: February 06, 2018, 01:35 PM »
I usually check the MFT for square each time before I begin a project. I know it seems a lot but, I have my MFT on a cart I built and I seem to grab the fence sometimes to move the cart around. I think it has gotten to be a habit now to check the MFT.  8)

Offline SoonerFan

  • Posts: 402
Re: MFT squaring
« Reply #3 on: February 06, 2018, 09:59 PM »
Rarely do I find my MFT/3 out of square.  I check the cut more often when dry fitting than I do the actual table.  I probably check it at the start of a new project plus whenever I reinstall the fence. 

Offline Bohdan

  • Posts: 880
Re: MFT squaring
« Reply #4 on: February 07, 2018, 01:02 AM »
If you adjust the height of your rail to suit the various thicknesses of material correctly it won't go out of square.

The correct proceedure is to put the material under the rail. Release both rail clamps and, while holding the rail down flat on the material, tighten the back clamp.

Now, while holding the rail down flat on the material, raise the front clamp so that the pin indexes the rail and the clamp is square against the rail, tighten the front clamp.

Your rail is now set at the correct height and should be square.

If the material is not wide enougth to reach from the fence to the front clamp you have to either move the material or use another piece of packing that is the same thickness.

Offline Trevin

  • Posts: 81
Re: MFT squaring
« Reply #5 on: February 07, 2018, 02:20 AM »
@Sparktrician
Willy looks upset!  hala...... [smile]
Festool: MFT3 (x2), OF1010, OF1400, LR32, Domino DF500, Domino XL DF700, Kapex KS120, TS-75, Carvex 420, CXS, C-18, Vecturo OS 400, DTS 400, Pro 5, Rotex 125, VAC-PMP, VAC-SYS-1, VAC-SYS-2, CT-26 (x2), CT-SYS, SYS Light DUO, SYS-ROCK
Other: Minmax FS41, Sawstop PCS (3HP, 52"), Laguna BX14, Jet 17" Drill Press, Rikon 70-220VSR Lathe, Incra LS Router Station, Laguna P/Flux 3 Dust Collector

Offline Birdhunter

  • Posts: 2339
  • Woodworker, Sportsman, Retired
Re: MFT squaring
« Reply #6 on: February 07, 2018, 06:00 AM »
I check mine before starting a project. I use a Woodpecker framing square or their MFT special purpose square.

The only time it has been out of square is when one of the fasteners on the pivot loosened.

I’ll always make a test cut before cutting into the real stuff. I butt the top of the wood against Qwas dogs and my rail has the Slop Stop piece. The cuts come out square.
Birdhunter

Offline Don Ware

  • Festool Dealer
  • *
  • Posts: 71
  • Anderson Plywood
Re: MFT squaring
« Reply #7 on: February 13, 2018, 11:52 PM »
Don Ware
Anderson Plywood Sales
Culver City, California