Author Topic: Power Of 1010?  (Read 1217 times)

0 Members and 1 Guest are viewing this topic.

Offline darita

  • Posts: 292
Power Of 1010?
« on: September 03, 2018, 04:28 PM »
I've got a 1010 and would like to use it with my Leigh D4R Pro Jig, however the power requirement for the best cut is 1 1/2 to 2 hp.  Will this router do the job?

Festool USA does not pre-approve the contents of this website nor endorse the application or use of any Festool product in any way other than in the manner described in the Festool Instruction Manual. To reduce the risk of serious injury and/or damage to your Festool product, always read, understand and follow all warnings and instructions in your Festool product's Instruction Manual. Although Festool strives for accuracy in the website material, the website may contain inaccuracies. Festool makes no representations about the accuracy, reliability, completeness or timeliness of the material on this website or about the results to be obtained from using the website. Festool and its affiliates cannot be responsible for improper postings or your reliance on the website's material. Your use of any material contained on this website is entirely at your own risk. The content contained on this site is provided for informational purposes only and does not constitute professional advice.


Offline Roseland

  • Posts: 568
Re: Power Of 1010?
« Reply #1 on: September 03, 2018, 05:33 PM »
No problem.  I have an OF1010 and a D4R and I think it’s just fine.

Andrew
TS55, MFT/3, OF1400, OF1010, CT26, RS100, ETS125, CXS, MFS400, DF-500, Zobos.

Offline Coen

  • Posts: 364
Re: Power Of 1010?
« Reply #2 on: September 04, 2018, 01:26 PM »
Ask them what the metric requirement is...

Google says one hp is 746W

The 1010 is ... 1010W

Funny thing btw; 1010's were listed or sold with 22.000, 23.000 and 24.000 rpm

Type plate of mine was 23.000 while the old catalog said 22.000 and the newer catalogs say 24.000

Never compared if they really differ though.

Online Joe Felchlin

  • Posts: 128
  • Just another day in paradise - Livin’ the dream!
Re: Power Of 1010?
« Reply #3 on: September 04, 2018, 02:10 PM »
Absolutely a great combination - Works just fine.
FOG member Peter Parfitt has a number of great videos on the OF 1010 -
And says the D4R and the OF 1010 are his preferred combination.
And... If Peter says it - You can “take it to the bank”.  [smile]
FESTOOL: CT26 and CT33 E HEPA Dust Extractors, MFT 1080, MFT-3, TS 55 REQ-F-Plus USA, TS75 EQ, Guide Rails: 1080's/1400/3000mm, LR 32-SYS/Holey Rail, Parallel Guides and Extensions, OF1400 EQ Plunge Router, OF1010 EQ Plunge Router, HL 850 Planer, RO125 FEQ Rotex Sander, LS 130 EQ Linear Detail Sander, DX93E Detail Sander, C12 Cordless Drill, CXS Cordless Compact Drill Driver, SYS-Centrotec-Set, Domino XL DF 700 EQ Plus Tenon Joiner Set, Domino DF 500 Tenon Joiner | WOODPECKERS: DF 500 Offset Base System | BOSCH: 5412L Compound Miter Saw, 4100-09 10-Inch Table Saw | POWERMATIC: 60HH 8" Jointer, PWBS 14" Bandsaw w/Riser Block | MAKITA: 2012NB Bench Top Planer | JESSEM: Mast-R-Lift XL/Fence/Slide, Rout-R-Plate/Table Stand | RIKON: 50-120 6inX48in Belt-Disc Sander | JET: JBOS-5 Benchtop Oscillating Spindle Sander | PORTER CABLE: 7518 and 690LVRS Routers, 557 Pro Plate Joiner, 16/18/23 Gauge Nailers | LEIGH JIGS: D4R 24 Pro Dovetail Jig, FMT Pro Mortise & Tenon Jig | LIE-NIELSEN: Almost every hand plane | DOWELMAX: 3/8" and 1/4" | KREG: K3 Master System | FEIN: Multimaster FMM 250 Q Kit | TORMEK: Super-Grind 2000 | DUST DEPUTY: Industrial (ALL) Steel Deluxe Cyclone (2)

Online Sparktrician

  • Posts: 3617
Re: Power Of 1010?
« Reply #4 on: September 04, 2018, 07:06 PM »

The 1010 is ... 1010W

 

1010 Watts = 1.3544323 hp.   [smile]
- Willy -

 "Remember, a chip on the shoulder is a sure sign of wood higher up." - Brigham Young

Offline Jim_in_PA

  • Posts: 36
Re: Power Of 1010?
« Reply #5 on: September 05, 2018, 01:25 PM »
While I personally prefer to use a fixed base router with my D4, I have used my OF1010 with zero issue with my 8mm Leigh cutters. It has plenty of power for almost any bit that's normal to use with a 1/4" or 8mm shank including dovetail cutters.
----
ETS 150/3, Rotex 150, OF1010, OF1400, Trion PS 300, TDK-12, CT-22, MFT 1080, TS55, Domino XL DF 700, 8' track, (2) 55" tracks

SCM MiniMax S315WS, FS350, MM16, Camaster Stinger II SR-44 CNC