Author Topic: TS75  (Read 1141 times)

0 Members and 1 Guest are viewing this topic.

Offline SoonerFan

  • Posts: 402
TS75
« on: April 05, 2018, 06:39 PM »
I have recently had few projects that required 5/4 hardwoods like maple and walnut.  And I have a few more to do in the coming months.  I have looked at the TS 75 before a couple times.  However, I always seemed to get by with my trusted 55 by using the right blade and keeping the blades sharp.  A few times recently my 55 struggled with the projects, especially with the maple.  On the maple there were a couple blade marks and some slight burn marks on longer cuts.  The blade marks and burning easily sanded off.

Is it far to assume a TS75 with th factory blade would cut 5/4 hardwoods with ease and without markings/burn marks.  If so, I think I will get one and likely look for a metric sticker since I am sure the metric version here in the U.S. are long, long gone.

Thanks. 


Festool USA does not pre-approve the contents of this website nor endorse the application or use of any Festool product in any way other than in the manner described in the Festool Instruction Manual. To reduce the risk of serious injury and/or damage to your Festool product, always read, understand and follow all warnings and instructions in your Festool product's Instruction Manual. Although Festool strives for accuracy in the website material, the website may contain inaccuracies. Festool makes no representations about the accuracy, reliability, completeness or timeliness of the material on this website or about the results to be obtained from using the website. Festool and its affiliates cannot be responsible for improper postings or your reliance on the website's material. Your use of any material contained on this website is entirely at your own risk. The content contained on this site is provided for informational purposes only and does not constitute professional advice.


Offline leakyroof

  • Posts: 2197
Re: TS75
« Reply #1 on: April 05, 2018, 06:58 PM »
I have heard from multiple TS 75 owners that they handle Hardwood with ease compared to the small 55.

Update- I now OWN a TS75, used, but in nice shape.
I cut a 4x4 post on my back gate as a test for my first time using it.
Granted, only Cedar, so ,soft and easy to cut.
Had to trim about 1 1/4” off the top of one post to even it with its mate after redoing the footing on the post a few months ago, clamped an OLD Festool track to the post and cut away, no issues.
Moved the track around for the remaining cut, done.
Thanks again Kurt for selling me this Saw. ..... [thumbs up] [thumbs up]
« Last Edit: June 23, 2018, 05:38 PM by leakyroof »
Not as many Sanders as PA Floor guy.....

Offline Svar

  • Posts: 1471
Re: TS75
« Reply #2 on: April 05, 2018, 07:26 PM »
With TS75 and standard blade (36T) I often cut 40-50 mm hardwoods, including maple, in a single pass without problems and usually without burn marks.

Offline Joe Felchlin

  • Posts: 137
  • Just another day in paradise - Livin’ the dream!
Re: TS75
« Reply #3 on: April 05, 2018, 08:13 PM »
I chose the TS75 over the TS55 - More than 10 years ago.
A bit heavier to handle (and I’m older/retired) -
And yes - It did cost more...
But the TS75 cuts anything - Rips or cross cuts.
I’ve used it to rip 8’ X 2-1/2” thick hardwoods - With the original “combo” blade -
And my 3000mm guide rail.
No problem.
I’ve never regretted choosing the 75 over the 55.
Go for it. You won’t either!
Like they say: “Bigger is better.” 👍
Joe
« Last Edit: April 07, 2018, 11:20 AM by Joe Felchlin »
FESTOOL: CT26 and CT33 E HEPA Dust Extractors, MFT 1080, MFT-3, TS 55 REQ-F-Plus USA, TS75 EQ, Guide Rails: 1080's/1400/3000mm, LR 32-SYS/Holey Rail, Parallel Guides and Extensions, OF1400 EQ Plunge Router, OF1010 EQ Plunge Router, HL 850 Planer, RO125 FEQ Rotex Sander, LS 130 EQ Linear Detail Sander, DX93E Detail Sander, C12 Cordless Drill, CXS Cordless Compact Drill Driver, SYS-Centrotec-Set, Domino XL DF 700 EQ Plus Tenon Joiner Set, Domino DF 500 Tenon Joiner | WOODPECKERS: DF 500 Offset Base System | BOSCH: 5412L Compound Miter Saw, 4100-09 10-Inch Table Saw | POWERMATIC: 60HH 8" Jointer, PWBS 14" Bandsaw w/Riser Block | MAKITA: 2012NB Bench Top Planer | JESSEM: Mast-R-Lift XL/Fence/Slide, Rout-R-Plate/Table Stand | RIKON: 50-120 6inX48in Belt-Disc Sander | JET: JBOS-5 Benchtop Oscillating Spindle Sander | PORTER CABLE: 7518 and 690LVRS Routers, 557 Pro Plate Joiner, 16/18/23 Gauge Nailers | LEIGH JIGS: D4R 24 Pro Dovetail Jig, FMT Pro Mortise & Tenon Jig | LIE-NIELSEN: Almost every hand plane | DOWELMAX: 3/8" and 1/4" | KREG: K3 Master System | FEIN: Multimaster FMM 250 Q Kit | TORMEK: Super-Grind 2000 | DUST DEPUTY: Industrial (ALL) Steel Deluxe Cyclone (2)

Offline SoonerFan

  • Posts: 402
Re: TS75
« Reply #4 on: April 05, 2018, 09:18 PM »
@leakyroof  @Svar  and @Joe Felchlin

Thanks for the replies.  Your comments confirmed what I expected.  I just ordered a TS75 from @Shane Holland and my friends at Toolnut / Festool Products.

Thanks again for the input.
« Last Edit: April 05, 2018, 10:07 PM by SoonerFan »

Re: TS75
« Reply #5 on: June 23, 2018, 12:03 PM »
If you’re cutting at 90° then it is not too much of a problem. As soon as you want to do any compound cuts the wight becomes an issue. That’s my two bits

Offline ChuckM

  • Posts: 619
Re: TS75
« Reply #6 on: June 23, 2018, 03:23 PM »
The difference is only 3.5 lbs, even less than the difference between a DF500 and XL. I have used both the T55 and TS75 (which I own) for long bevel cuts and did not feel or see any difference in control or quality of cuts. I am talking about making the cuts with the track.