Woodworking & Power Tools Forum - Festool Owners Group > FESTOOL DISCUSSIONS > Festool Wish List > Festool Oscillating Hand Spindle Sander
Pages: [1]   Go Down
« previous next »
  Print  
Author Topic: Festool Oscillating Hand Spindle Sander  (Read 1775 times)
0 Members and 1 Guest are viewing this topic.
Gene Howerton

Offline Offline

Location: UNITED STATES (US)
Member Since: Feb 2007
Posts: 97
« on: December 03, 2009, 03:15 PM »
I wish that Festool would make a sander like the Porter-Cable 121 6 Amp Hand Held Oscillating Spindle Sander, but with better dust collection and the future ability to be added into the CMS System for drum sanding with a platform.  It would make a nice addition for the Festool sanding line.

* PC Sander.jpg (3.63 KB, 160x160 - viewed 126 times.)
Logged
Festool USA does not pre-approve the contents of this website nor endorse the application or use of any Festool product in any way other than in the manner described in the Festool Instruction Manual. To reduce the risk of serious injury and/or damage to your Festool product, always read, understand and follow all warnings and instructions in your Festool product's Instruction Manual. Although Festool strives for accuracy in the website material, the website may contain inaccuracies. Festool makes no representations about the accuracy, reliability, completeness or timeliness of the material on this website or about the results to be obtained from using the website. Festool and its affiliates cannot be responsible for improper postings or your reliance on the website's material. Your use of any material contained on this website is entirely at your own risk. The content contained on this site is provided for informational purposes only and does not constitute professional advice.

Corwin

Online Online

Location: Washington State, USA
Member Since: Jan 2007
Posts: 1993
« Reply #1 on: December 03, 2009, 03:55 PM »
I've had the same wish...  Until then, Woodpeckers makes a plate for the PC 121 for table mounting -- the plate is only produced on a limited bases, and is not always available.  I keep my PC 121 and the Woodpecker plate in a Systainer 5.  They'll also fit into a Systainer 4.
Logged
Shirt Size:  L
Gene Howerton

Offline Offline

Location: UNITED STATES (US)
Member Since: Feb 2007
Posts: 97
« Reply #2 on: December 03, 2009, 05:56 PM »
I have looked at that before, but would like it better if it was Festool.  Wink
Logged
Charimon

Offline Offline

Location: Omaha NE
Member Since: Jun 2008
Posts: 652


Tool and Tile Junkie
« Reply #3 on: December 03, 2009, 11:14 PM »
I would be happy to privately rebadge one for you  Scared
Logged
"The existence of the flame thrower proves that at one time, somewhere, somebody said, " You Know, There's a group of people over there that I'd like to set on fire right now but they're too far away."
Frans

Offline Offline

Location: NETHERLANDS (NL)
Member Since: Jan 2007
Posts: 113
« Reply #4 on: December 04, 2009, 04:22 AM »
I already posted that in july 2008 here. Can't say my post was received with raving enthusiasm, though...

I also emailed Festool Germany about it, they sent me this reply:

Dear Mr. ******,

thank you very much for sending us your idea regarding an new sander for the CMS system. For the moment we have not planned starting activities for making new products for the CMS product group. If we have the capacity to start new products in this segment we will put up your idea an discuss it.   

Please don?t hesitate to send us your ideas. If we have the possibility and see a potential for the idea we do our best to realize it. 

Thanks again for sending the idea

Best regards

i. A. Roland M?nz

So I doubt we'll be in much luck. And the PC121 isn't for sale here in Europe, unfortunately.

Frans
Logged
Pages: [1]   Go Up
  Print  
« previous next »
 
Jump to: