Author Topic: Fill in the blank: I wish Festool made a ______!  (Read 382035 times)

0 Members and 1 Guest are viewing this topic.

Offline Bob D.

  • Posts: 586
Re: Fill in the blank: I wish Festool made a ______!
« Reply #1020 on: June 27, 2017, 08:41 AM »
"That does not stop people from complaining."

Is complaining the correct term? Maybe desire
or want or request would better describe their
request for such a tool compatible with the
power available in their country or region.
-----
It's a table saw, do you know where your fingers are?

Festool USA does not pre-approve the contents of this website nor endorse the application or use of any Festool product in any way other than in the manner described in the Festool Instruction Manual. To reduce the risk of serious injury and/or damage to your Festool product, always read, understand and follow all warnings and instructions in your Festool product's Instruction Manual. Although Festool strives for accuracy in the website material, the website may contain inaccuracies. Festool makes no representations about the accuracy, reliability, completeness or timeliness of the material on this website or about the results to be obtained from using the website. Festool and its affiliates cannot be responsible for improper postings or your reliance on the website's material. Your use of any material contained on this website is entirely at your own risk. The content contained on this site is provided for informational purposes only and does not constitute professional advice.


Offline Holmz

  • Posts: 3759
Re: Fill in the blank: I wish Festool made a ______!
« Reply #1021 on: June 27, 2017, 07:49 PM »
"That does not stop people from complaining."

Is complaining the correct term? Maybe desire
or want or request would better describe their
request for such a tool compatible with the
power available in their country or region.

Well I suppose it is in the ears of the beholder.

When NAINA is mentioned the tone is often toward frustration rather than hope.

If they were actually complaining, then their countenance could be made glowing with a transformer.

While that is a good solution to fix the issue of power, it is not the solution that they want, and often results in a further sourness upon their countenance.

The obvious long term solution is to head to DC brushless motors. Either batteries or a transformer that goes into a DC slot from the wall.

If they can buy a similar tool that does the required task, but do it like the colour or cost, then they are truly complaining.

Offline Naildrivingman

  • Posts: 264
Re: Fill in the blank: I wish Festool made a ______!
« Reply #1022 on: August 13, 2017, 08:41 AM »
Nothing new!  I'm going broke!
Dance with who brung ya...

Offline Woodwork Wizard

  • Posts: 419
Re: Fill in the blank: I wish Festool made a ______!
« Reply #1023 on: August 13, 2017, 12:53 PM »
I wish Festool made splinter guard tape that stayed stuck to the guide rail. Makita can.

Offline pettyconstruction

  • Posts: 339
Re: Fill in the blank: I wish Festool made a ______!
« Reply #1024 on: August 13, 2017, 02:13 PM »
I , like a lot of people here,went with the  Makita splinter guard. Works better
Charlie


Sent from my iPhone using Tapatalk Pro

Offline Dovetail65

  • Posts: 4591
    • Rose Farm Floor Medallions and Inlays
Re: Fill in the blank: I wish Festool made a ______!
« Reply #1025 on: August 13, 2017, 10:28 PM »
I wish Festool made upgraded routers.

It's time to update the complete line of routers. They all need LED rings, Festool should come out with the best LED lighting system made for routers with no shadow and pure white light, even dimmable on/off switching.

The turret system on OF1010 and OF 1400 leave some to be desired. The OF 1010 can use some more power too. My little DeWalt in use seems truly more powerful.

The OF 2200 plastic shroud plastic over the years became very difficult to see through, change the plastic type. Make the 2 point contact clamp a 4 point system for the attachment rods.

Heck, I prefer the OF 1010 and OF 1400 design be scrapped altogether and just make them look identical to the OF 2200. Shrunken down small OF 2200 style routers would be awesome.

« Last Edit: August 13, 2017, 10:32 PM by Dovetail65 »
The one who says it can't be done should avoid interrupting the person doing it.

Offline WilliamO

  • Posts: 1
Re: Fill in the blank: I wish Festool made a ______!
« Reply #1026 on: August 27, 2017, 03:40 AM »
4.5 inch (114 mm) trim saw

Offline jobsworth

  • Posts: 4394
  • Burger Babe Says: I Even Buy Green Bananas
Re: Fill in the blank: I wish Festool made a ______!
« Reply #1027 on: August 27, 2017, 09:05 AM »
I wish they made a sawmill but then it would cost 3xs the cost of a milwaukie
Loving the Calif sun....

Offline dastueve

  • Posts: 1
Re: Fill in the blank: I wish Festool made a ______!
« Reply #1028 on: Yesterday at 08:34 AM »
I would like Festool to make a drill attachment to emulate a drill press in a portable way.  This would provide a straight drill platform with repeatable drilling.  I use my router regularly, but would like a simple mobile solution.

Offline Euclid

  • Posts: 101
Re: Fill in the blank: I wish Festool made a ______!
« Reply #1029 on: Yesterday at 05:36 PM »
I would like Festool to make a drill attachment to emulate a drill press in a portable way.  This would provide a straight drill platform with repeatable drilling.  I use my router regularly, but would like a simple mobile solution.

Do you mean something like this…?
https://www.festool.co.uk/products/timber-construction/drilling-guide-systems/768768---gd-320#Overview
I think they are intended, principally, for long holes in timber construction work; though there are much smaller (and less expensive) items (from Wolfcraft, for example) which work in the same way.
Or are you thinking of something different?

Offline rst

  • Posts: 1501
Re: Fill in the blank: I wish Festool made a ______!
« Reply #1030 on: Yesterday at 08:46 PM »
Not Festool but very interesting...youtube.com/watch?v=LDa2bSWLvcE.