Woodworking & Power Tools Forum - Festool Owners Group > GENERAL DISCUSSIONS > Finishing and Painting > Flexifoam abrasives
Pages: [1]   Go Down
« previous next »
  Print  
Author Topic: Flexifoam abrasives  (Read 1616 times)
0 Members and 1 Guest are viewing this topic.
John Bates
Retailer

Offline Offline

Location: UK
Member Since: Dec 2010
Posts: 76
« on: April 30, 2012, 03:48 PM »
Any of you European guys familiar with Flexifoam foam backed abrasives, I have samples to try out and so far I'm very impressed. I'm an agent for Famag and thought these would be a natural add-on. I never normally aim for very fine finish but would like to hear if any one has any experience with these.
Logged
Manufacturer's agent, sshh! Don't tell anyone!
Festool USA does not pre-approve the contents of this website nor endorse the application or use of any Festool product in any way other than in the manner described in the Festool Instruction Manual. To reduce the risk of serious injury and/or damage to your Festool product, always read, understand and follow all warnings and instructions in your Festool product's Instruction Manual. Although Festool strives for accuracy in the website material, the website may contain inaccuracies. Festool makes no representations about the accuracy, reliability, completeness or timeliness of the material on this website or about the results to be obtained from using the website. Festool and its affiliates cannot be responsible for improper postings or your reliance on the website's material. Your use of any material contained on this website is entirely at your own risk. The content contained on this site is provided for informational purposes only and does not constitute professional advice.

jmarkflesher

Offline Offline

Location: flemington,nj usa
Member Since: Aug 2010
Posts: 97


Scoot
« Reply #1 on: April 30, 2012, 05:43 PM »
By flexifoam back do you mean the waffle type material that is also used for sanding mats and tool drawer liners? If so 3M sells a product about 2.5" wide by 4" long. I've used it in 80 and 180 grit on a lathe. It works great, no heat build up.
Logged
DEC 21st, 2012 TIC TIC TIC   WAS A DUD
John Bates
Retailer

Offline Offline

Location: UK
Member Since: Dec 2010
Posts: 76
« Reply #2 on: April 30, 2012, 06:09 PM »
Not the mat material, it's made by a company in Belgium called Flexifoam. They make it on rolls, blocks and pads in a range of grits to give the smoothest finish I've come across.
Www.flexifoam.com
Logged
Manufacturer's agent, sshh! Don't tell anyone!
neeleman

Online Online

Location: Rotterdam - The Netherlands
Member Since: Jan 2010
Posts: 256
« Reply #3 on: May 05, 2012, 04:15 PM »
Hi John,

I use the red Flexifoam double foam type of pads and the single ones which come on the rolls.
I do like the double foam type the best because you always have a good grip with your fingers on the grid.
Both types last very long and you can use them for dry or wet sanding.
Afterwards you can clean them with normal water. They also claim no hand fatigue.
These are the best foam abrasives I have used until now.
Logged
Precisio CS50 EB-Set, Kapex KS120-UG Set, TS55 R EBQ, Carvex PS420 EQ, BS75 E, RAS115.04 E, Rotex RO90 DX, Rotex RO150 FEQ, DTS400 EQ, RS400 EQ, RTS400 EQ, RS300 EQ, Duplex LS130 EQ, Deltex DX93 E, ETS150/5 EQ, Domino DF500 Q, OF1010 EBQ, OF1400 EBQ, OFK500 Q, MFK700 EQ, C12-Li, T15+3, TI15 Impact, T18+3, CTL26 E, CTL22 E SG, CTL Midi, EHL65 E, D27-AS Plug-it, D36 UNI-RS, FS800, FS1400/2, Gecko Dosh, Toolie, CE-SYS-2010, RB-SYS CART, Syslite KAL, LEV1400, Protool PDC 18-4, Protool FLC UNI.
Tom Bellemare
Festool Dealer

Offline Offline

Location: Austin, Texas - USA
Member Since: Nov 2007
Posts: 3557


Festool demo's & personal service in Central Texas


WWW
« Reply #4 on: May 05, 2012, 05:07 PM »
Festool:




Flexifoam:




Tom
Logged
Tom Bellemare
Customer Svc
Tool Home
www.tool-home.com
512-428-9140
John Bates
Retailer

Offline Offline

Location: UK
Member Since: Dec 2010
Posts: 76
« Reply #5 on: May 05, 2012, 05:11 PM »
That's the stuff, my feedback so far has been 100% but it's always good to get independent feedback. When I tried it on oak I was very impressed on the finish and comfort, it also seems to last well compared to the sanding blocks I've used before.
Thanks for the feedback.
Logged
Manufacturer's agent, sshh! Don't tell anyone!
Pages: [1]   Go Up
  Print  
« previous next »
 
Jump to: