Author Topic: Flooring Question  (Read 1889 times)

0 Members and 1 Guest are viewing this topic.

Offline VW MICK

  • Posts: 881
Flooring Question
« on: September 20, 2018, 06:25 AM »
Hi

Just need a little advice on refinishing my ground floor flooring

It is 22mm solid oak so sanding isnt an issue. I intend to do the edges with my R/O
and a friend that does floors is going to come over with what he calls a trio ?
to do the main areas

Now my question is Originally the oak boards had a small chamfer all around
which has now after probabbly 15-20 years got very grubby 
How do I sand the chamfer ?
I dont think we are going to sand enough off to lose the chamfer
is it just a case of hands and knees with a block (dont fancy that idea)
Im sure there must be an easy way

any tips on refinishing the floor would be appreciated thanks
Mick

Festool USA does not pre-approve the contents of this website nor endorse the application or use of any Festool product in any way other than in the manner described in the Festool Instruction Manual. To reduce the risk of serious injury and/or damage to your Festool product, always read, understand and follow all warnings and instructions in your Festool product's Instruction Manual. Although Festool strives for accuracy in the website material, the website may contain inaccuracies. Festool makes no representations about the accuracy, reliability, completeness or timeliness of the material on this website or about the results to be obtained from using the website. Festool and its affiliates cannot be responsible for improper postings or your reliance on the website's material. Your use of any material contained on this website is entirely at your own risk. The content contained on this site is provided for informational purposes only and does not constitute professional advice.


Offline grobkuschelig

  • Posts: 440
Re: Flooring Question
« Reply #1 on: September 20, 2018, 06:31 AM »
Hi Mick,

I‘m not sure if this is an option, but Fein do make a set of sanding accessories for multitools, that allows you to make quicker work of it, compared to hand sanding at least.

I used this on the garden shed last year, where it went neatly into the tung and groove..

Might be a different thing, when looking at a floor, though.


Offline mrgeigh

  • Posts: 9
Re: Flooring Question
« Reply #2 on: September 20, 2018, 07:23 AM »
Perhaps a router with a chamfer bit on a guide rail.

Offline SRSemenza

  • Global Moderator
  • *
  • Posts: 8641
  • Finger Lakes Region, NY State , USA
Re: Flooring Question
« Reply #3 on: September 20, 2018, 08:47 AM »
How wide is the chamfer?


   Pull type scraper or LS130?

Seth

Offline tjbnwi

  • Posts: 5767
  • Cedar Tucky Indiana
Re: Flooring Question
« Reply #4 on: September 20, 2018, 04:41 PM »
If it is a micro bevel you will probably take it off completely when the floor is sanded.

If not, sandpaper over the edge of a square corner. It won’t take much to sand the area.

Tom

Offline Cheese

  • Posts: 5156
Re: Flooring Question
« Reply #5 on: September 20, 2018, 05:37 PM »
My in laws had a prefinished 3/4” thick wood floor installed.  When it was done they hated the small bevel that was around every board. So they hired a floor refinisher that showed up with a Hummel drum sander...problem solved.  [big grin]

Offline Pnw painter

  • Posts: 171
Re: Flooring Question
« Reply #6 on: September 20, 2018, 11:22 PM »
Ask your buddy for advice. I’m sure he’s dealt with it in the past. It’s also possible that the chamfer won’t be there after your buddy is finished sanding.


Sent from my iPhone using Tapatalk

Offline Peter_C

  • Posts: 723
Re: Flooring Question
« Reply #7 on: September 20, 2018, 11:51 PM »
I wouldn't count on the RO150 or any Festool sander (Maybe an RAS) for doing the edge work after sanding the main parts of the floor. Have your buddy bring over a real edger and get the job done in a reasonable amount of time.

Offline Alanbach

  • Posts: 178
Re: Flooring Question
« Reply #8 on: September 29, 2018, 05:58 PM »
The Trio should get within a 1/4” of the edge so I don’t think that you will need (or want) an edger. The Trio machine looks like a buffer but it is actually a three disc rotary sander unlike a typical floor sander that is a belt sander.