Author Topic: Non penetrating Stain  (Read 1234 times)

0 Members and 1 Guest are viewing this topic.

Offline pkslice

  • Posts: 2
Non penetrating Stain
« on: July 01, 2017, 08:56 PM »
I'm looking to build a coffee table similar to this one, but want to stain an american flag on the top, however I'm going to use painters tape/frog tape for the stripes and a wood polishing dremel bit for the stars to make them white below the stain. What type of stain should I be using, or is there a better way to do this?

Thanks,

pkslice

Festool USA does not pre-approve the contents of this website nor endorse the application or use of any Festool product in any way other than in the manner described in the Festool Instruction Manual. To reduce the risk of serious injury and/or damage to your Festool product, always read, understand and follow all warnings and instructions in your Festool product's Instruction Manual. Although Festool strives for accuracy in the website material, the website may contain inaccuracies. Festool makes no representations about the accuracy, reliability, completeness or timeliness of the material on this website or about the results to be obtained from using the website. Festool and its affiliates cannot be responsible for improper postings or your reliance on the website's material. Your use of any material contained on this website is entirely at your own risk. The content contained on this site is provided for informational purposes only and does not constitute professional advice.


Offline antss

  • Posts: 1180
Re: Non penetrating Stain
« Reply #1 on: July 02, 2017, 08:23 AM »
Paint.

I'd think stains, even opaque ones , will be too thin to accomplish what your asking. 

I've also never seen white stain.

Offline Dovetail65

  • Posts: 4594
    • Rose Farm Floor Medallions and Inlays
Re: Non penetrating Stain
« Reply #2 on: July 02, 2017, 09:14 AM »
I think Milk Paint could be better for something like that:






http://designs.generalfinishes.com/posts/american-flag-inspired-desk#.WVjxK-mQxPY

General Finishes has loads of examples of very similar projects to what you propose:

http://designs.generalfinishes.com/color-category/union-jack-flags

The one who says it can't be done should avoid interrupting the person doing it.

Offline SRSemenza

  • Global Moderator
  • *
  • Posts: 7840
  • Finger Lakes Region, NY State , USA
Re: Non penetrating Stain
« Reply #3 on: July 02, 2017, 11:10 AM »
I think stain , even non-penetrating, might bleed under the tape unlike paint. I'd go with paint and then maybe a clear coat on top for protection.

Seth

Offline RustE

  • Posts: 166
Re: Non penetrating Stain
« Reply #4 on: July 02, 2017, 01:55 PM »
General Finishes Gel Stains are low penetration.  I'm not sure what options are available to make the colors you'll need.  As already mentioned, look around the General Finishes website for a bit.

Offline JBag09

  • Posts: 159
Re: Non penetrating Stain
« Reply #5 on: July 03, 2017, 08:33 AM »
I've used the GF gel stains a lot. I have used frog tape when I needed the stain to stop at a certain point, and the bleeding is almost zero. But as far as colors, they pretty much just come in standard stain colors.


Sent from my iPhone using Tapatalk

Offline pkslice

  • Posts: 2
Re: Non penetrating Stain
« Reply #6 on: July 03, 2017, 08:36 AM »
I'm going to do everything in a standard stain color I'm not looking for stains that would do red white and blue if I was going to do that I would just use paint

Sent from my SAMSUNG-SM-G930A using Tapatalk