Author Topic: Trying to achieve a "swirl-less" finish on epoxy  (Read 473 times)

0 Members and 1 Guest are viewing this topic.

Offline honoluahomes

  • Posts: 1
Trying to achieve a "swirl-less" finish on epoxy
« on: October 01, 2017, 03:16 PM »
I used colored/pigmented epoxy for signs and decorative art.  I was having some trouble with the old Dewalt RO sander I used especially with fine grade paper (say 400 grit and up).

So I took the plunge and got a Festool Rotext 150 believing that the integrated dust collection would help pull the sanded epoxy away from the work and not grind it into the epoxy like I was seeing with the Dewalt.

The Rotext & vacuum did alleviate the problem of the sanding the dust back into the work piece but the issue I'm having now is that I can't get anywhere close to the swirl-less finish I was looking for.  I purchased some Rubin 60-120 paper and in "aggressive" mode it does a pretty good job of evenly sanding the surface up with nothing in the way of distinct scratches or swirls.

As soon as I move over to the 220+ grit Granat (using RO mode) the paper just gums up and nothing but scratches and swirls.  In fact, it's far worse than even the big box Dewalt sander and paper (with the exception of not leaving behind a significant amount dust to grind back into the piece).  It has to be something I'm doing....wrong paper, wrong approach but I'm at a loss.

Any ideas, comments or suggestions would be appreciated!!

Festool USA does not pre-approve the contents of this website nor endorse the application or use of any Festool product in any way other than in the manner described in the Festool Instruction Manual. To reduce the risk of serious injury and/or damage to your Festool product, always read, understand and follow all warnings and instructions in your Festool product's Instruction Manual. Although Festool strives for accuracy in the website material, the website may contain inaccuracies. Festool makes no representations about the accuracy, reliability, completeness or timeliness of the material on this website or about the results to be obtained from using the website. Festool and its affiliates cannot be responsible for improper postings or your reliance on the website's material. Your use of any material contained on this website is entirely at your own risk. The content contained on this site is provided for informational purposes only and does not constitute professional advice.


Offline Michael Kellough

  • Posts: 2901
Re: Trying to achieve a "swirl-less" finish on epoxy
« Reply #1 on: October 01, 2017, 03:25 PM »
Turn the suction all the way down on the vac.
Reduce the speed of the sander.
Move the sander around quickly so the epoxy doesn't get too warm and gummy.

Online Peter Halle

  • Global Moderator
  • *
  • Posts: 10780
  • Let's Redux / Revive / Rewind / Rollback the FOG!
Re: Trying to achieve a "swirl-less" finish on epoxy
« Reply #2 on: October 01, 2017, 03:31 PM »
Also might want to throw in a grit between your 120 and 220 and make sure you wipe between grit changes.  Last thing you need is coarse grit being swirled around on the finer pad.

Peter
Disclaimer:  I have been involved with the development of some TSO Products.  I have offered thoughts and ideas freely.  I am not paid but I may receive products during the development process or afterwards.

Offline Holmz

  • Posts: 3879
Re: Trying to achieve a "swirl-less" finish on epoxy
« Reply #3 on: October 01, 2017, 05:05 PM »
Is an epoxy a thermoplastic? or a thermoset?
More power and more heat will tend to soften the surface. A softened surface tends to gums up.

You may need to "do it wet"...  In which case a pneumatic sander could be better than a "PlugIt in a bucket".
but I am no expert in this so you need to check.

Offline bkharman

  • Posts: 1937
Trying to achieve a "swirl-less" finish on epoxy
« Reply #4 on: October 01, 2017, 08:06 PM »
Might want to also try the abranet screens from Mirka. The elimination of the actual holes might help any Corning that is happening.

Cheers. Bryan.


Sent from my iPhone using Tapatalk
People, I just want to say, you know, can we all get along? Can we get along?