« previous next »
Pages: [1]   Go Down

Author Topic: The Parf Vice Video - an easy to make accessory  (Read 4459 times)

0 Members and 1 Guest are viewing this topic.

Offline Peter Parfitt

  • Magazine/Blog Author
  • *
  • Posts: 3645
    • New Brit Workshop on YouTube
The Parf Vice Video - an easy to make accessory
« on: March 03, 2017, 11:45 AM »
Hi Everyone

I have been playing with ideas for a simple vice to fit on the MFT3 or any other bench with the same pattern of 20 mm holes.

My solution is the Parf Vice and it should take no more than 2 hours for a novice to make one. The only items to buy would be a pair of suitable clamps (I used some from Axminster but there are other similar ones around) and the screw knobs to hold it in place (assuming you already have a pair of the Veritas small Parf Dogs).

Here is the link:



If you would like the plans then please note that I need your email address in order to get them to you. If you look carefully at the video all of the elements of the plans are shown and you should be able to read the dimensions from the screen.

Peter
Logged
Festool USA does not pre-approve the contents of this website nor endorse the application or use of any Festool product in any way other than in the manner described in the Festool Instruction Manual. To reduce the risk of serious injury and/or damage to your Festool product, always read, understand and follow all warnings and instructions in your Festool product's Instruction Manual. Although Festool strives for accuracy in the website material, the website may contain inaccuracies. Festool makes no representations about the accuracy, reliability, completeness or timeliness of the material on this website or about the results to be obtained from using the website. Festool and its affiliates cannot be responsible for improper postings or your reliance on the website's material. Your use of any material contained on this website is entirely at your own risk. The content contained on this site is provided for informational purposes only and does not constitute professional advice.

Offline jools

  • Posts: 255
Re: The Parf Vice Video - an easy to make accessory
« Reply #1 on: March 03, 2017, 02:04 PM »
Peter do you ever sleep? [big grin] The best ideas are the simplest and I like this a lot. I don't think the racking is an issue to put one off building it. It's perfect for those small sawing or planing jobs.
Best regards
Jools
Logged
It started with one little sander

Offline Peter Parfitt

  • Magazine/Blog Author
  • *
  • Posts: 3645
    • New Brit Workshop on YouTube
Re: The Parf Vice Video - an easy to make accessory
« Reply #2 on: March 03, 2017, 05:22 PM »
Quote from: jools on March 03, 2017, 02:04 PM
Peter do you ever sleep? [big grin] The best ideas are the simplest and I like this a lot. I don't think the racking is an issue to put one off building it. It's perfect for those small sawing or planing jobs.
Best regards
Jools

Hi Jools

The alarm goes off at 5.30 am and I listen to the early morning news on Radio 4 - the best news of the day !

I agree that the racking is not an issue for a small vice like this. It would be easy to reduce the vertical racking by having something to keep the legs of the clamps from raising.

Cheers.

Peter
Logged

Offline Jeff Zanin

  • Posts: 213
Re: The Parf Vice Video - an easy to make accessory
« Reply #3 on: March 04, 2017, 06:48 AM »
Very nice work as usual, thanks Peter.

Is it a vice or a  ;Dvise? 
Logged

Offline Peter Parfitt

  • Magazine/Blog Author
  • *
  • Posts: 3645
    • New Brit Workshop on YouTube
Re: The Parf Vice Video - an easy to make accessory
« Reply #4 on: March 04, 2017, 07:26 AM »
Quote from: Jeff Zanin on March 04, 2017, 06:48 AM
Very nice work as usual, thanks Peter.

Is it a vice or a  ;Dvise?

I love it "DVice" or "DVise" for those that prefer.

Cheers.

Peter
Logged

Offline Dick Mahany

  • Posts: 95
Re: The Parf Vice Video - an easy to make accessory
« Reply #5 on: March 04, 2017, 08:45 AM »
Well done.  Simple, clever, quickly fabricated.  For the times that I have needed a quick vise away from my main workbench, this little device would work nicely.  For my intended uses, the racking issue wouldn't bother me.
Logged

Offline Jeff Zanin

  • Posts: 213
Re: The Parf Vice Video - an easy to make accessory
« Reply #6 on: March 04, 2017, 08:57 AM »
Quote from: Peter Parfitt on March 04, 2017, 07:26 AM
Quote from: Jeff Zanin on March 04, 2017, 06:48 AM
Very nice work as usual, thanks Peter.

Is it a vice or a  ;Dvise?

I love it "DVice" or "DVise" for those that prefer.

Cheers.

Peter

Arghhhh... The D was supposed to be a  ;D

Anyway, vice, vise, Dvice, Dvise, Pvise, whatever the name it is quite a nice vise.
Logged

Offline Peter Parfitt

  • Magazine/Blog Author
  • *
  • Posts: 3645
    • New Brit Workshop on YouTube
Re: The Parf Vice Video - an easy to make accessory
« Reply #7 on: March 04, 2017, 09:03 AM »
Quote from: Jeff Zanin on March 04, 2017, 08:57 AM
Quote from: Peter Parfitt on March 04, 2017, 07:26 AM
Quote from: Jeff Zanin on March 04, 2017, 06:48 AM
Very nice work as usual, thanks Peter.

Is it a vice or a  ;Dvise?

I love it "DVice" or "DVise" for those that prefer.

Cheers.

Peter

Arghhhh... The D was supposed to be a  ;D

Anyway, vice, vise, Dvice, Dvise, Pvise, whatever the name it is quite a nice vise.

We could have a silent "P" in front of Vice or Vise.

The only problem with a silent "P" in front of the vice is that the workshop floor gets wet !  [wink]

Peter
Logged

Offline schneems

  • Posts: 14
Re: The Parf Vice Video - an easy to make accessory
« Reply #8 on: March 04, 2017, 10:01 PM »
Cool idea! Any thoughts on ways of using this on the MFT/3 to plane some wood without having the whole thing spin in circles on the shop floor?
Logged

Offline Peter Parfitt

  • Magazine/Blog Author
  • *
  • Posts: 3645
    • New Brit Workshop on YouTube
Re: The Parf Vice Video - an easy to make accessory
« Reply #9 on: March 05, 2017, 01:59 AM »
Quote from: schneems on March 04, 2017, 10:01 PM
Cool idea! Any thoughts on ways of using this on the MFT/3 to plane some wood without having the whole thing spin in circles on the shop floor?

The MFT3 was designed to use mainly with power tools so there would be much less force applied across the surface than one gets with (say) planing.

You could try putting one end against a wall in order to react the force applied when working.

Festool do sell cross braces that stiffens up the legs a little but I have not tried them and so cannot recommend them.

Peter
Logged

Offline DiscoStu

  • Posts: 151
Re: The Parf Vice Video - an easy to make accessory
« Reply #10 on: March 05, 2017, 02:11 AM »
Surely it's a Parfvice or Parfice?


Sent from my iPhone using Tapatalk
Logged

Offline Bohdan

  • Posts: 766
Re: The Parf Vice Video - an easy to make accessory
« Reply #11 on: March 05, 2017, 03:17 AM »
Quote from: Peter Parfitt on March 05, 2017, 01:59 AM

Festool do sell cross braces that stiffens up the legs a little but I have not tried them and so cannot recommend them.

Peter

The cross braces stiffen up the MFT a lot but if you use it for hand planing it will still slide across the floor so you need to brace it up against the nearest wall.
Logged

Offline clark_fork

  • Posts: 242
Re: The Parf Vice Video - an easy to make accessory
« Reply #12 on: March 05, 2017, 10:23 AM »
Quote from: schneems on March 04, 2017, 10:01 PM
Cool idea! Any thoughts on ways of using this on the MFT/3 to plane some wood without having the whole thing spin in circles on the shop floor?

If the table spins, it is time to sharpen the plane blade or re-set the blade height. Look sharp, be sharp!
Logged
Clark Fork

"A lot of people are afraid of heights. Not me, I'm afraid of widths."  Stephen Wright

"straight, smooth and square" Mr. Russell, first day high school shop class-1954

" What's the good of it?" My Sainted Grandmother

"You can't be too rich, too thin or have too many clamps." After my introduction to pocket joinery and now the MFT work process

"Don't make something unless it is both made necessary and useful; but if it is both necessary and useful,
don't hesitate to make it beautiful." -- Shaker dictum

Offline waho6o9

  • Posts: 1271
    • Garage Door Handyman.com
Re: The Parf Vice Video - an easy to make accessory
« Reply #13 on: March 05, 2017, 09:36 PM »
Quote from: schneems on March 04, 2017, 10:01 PM
Cool idea! Any thoughts on ways of using this on the MFT/3 to plane some wood without having the whole thing spin in circles on the shop floor?

Lag the MFT 3 to a 2 x 4 on a wall and it'll make it rock solid for hand planing.

259554-0


Logged
Pages: [1]   Go Up
« previous next »