Author Topic: Cutting Drywall with Vecturo  (Read 1128 times)

0 Members and 1 Guest are viewing this topic.

Offline mattmass

  • Posts: 32
Cutting Drywall with Vecturo
« on: March 17, 2017, 10:47 PM »
I have to open up a wall to investigate some water damage. I'd like do do a really clean job, and re-install the cut piece drywall back in once I'm done. I'm not yet sure what size hole I need, but maybe something like 5'x2'. In the past, I've used a handheld keyhole saw for things like this. It's fine, but I've found it really hard to make straight, precise cuts.

Anyone like a Vecturo for this kind of thing? It seems like an oscillating tool could be excellent here.  Especially paired with the right blade and the plunge base. Is that setup easy to slide over longer distances? What do you all think? Yes, I am trying to justify a new tool purchase ;)

Festool USA does not pre-approve the contents of this website nor endorse the application or use of any Festool product in any way other than in the manner described in the Festool Instruction Manual. To reduce the risk of serious injury and/or damage to your Festool product, always read, understand and follow all warnings and instructions in your Festool product's Instruction Manual. Although Festool strives for accuracy in the website material, the website may contain inaccuracies. Festool makes no representations about the accuracy, reliability, completeness or timeliness of the material on this website or about the results to be obtained from using the website. Festool and its affiliates cannot be responsible for improper postings or your reliance on the website's material. Your use of any material contained on this website is entirely at your own risk. The content contained on this site is provided for informational purposes only and does not constitute professional advice.


Offline tjbnwi

  • Posts: 4715
  • Cedar Tucky Indiana
Re: Cutting Drywall with Vecturo
« Reply #1 on: March 17, 2017, 11:37 PM »
It will work, at 5'x2' I'd use a TS-55.

Tom

Offline leakyroof

  • Posts: 1810
Re: Cutting Drywall with Vecturo
« Reply #2 on: March 18, 2017, 12:19 AM »
It will work, at 5'x2' I'd use a TS-55.

Tom
. Ya' know, it shows how much fun I've had on St. Patrick's Day when I mis- read your TS-55 advice and thought, Wow, a 2" long plunged cut, that's hard to do... Oh wait ... 5 FOOT by 2 FOOT Cut, well that makes more sense.... [embarassed]
Not as many Sanders as PA Floor guy.....

Offline tjbnwi

  • Posts: 4715
  • Cedar Tucky Indiana
Re: Cutting Drywall with Vecturo
« Reply #3 on: March 18, 2017, 12:25 AM »
It will work, at 5'x2' I'd use a TS-55.

Tom
. Ya' know, it shows how much fun I've had on St. Patrick's Day when I mis- read your TS-55 advice and thought, Wow, a 2" long plunged cut, that's hard to do... Oh wait ... 5 FOOT by 2 FOOT Cut, well that makes more sense.... [embarassed]

Festool green beer?

Tom

Offline bryan1982

  • Posts: 117
Re: Cutting Drywall with Vecturo
« Reply #4 on: March 18, 2017, 12:56 AM »
Hey

I cut gyprock out att the time with a multi tool i don't have a vecturo so dont jnow about the base.

Draw a line where you want to cut and free hand it.
Just be aware how deep the blade is.  I tend to go shallow on the first cut all the way around then complete going all the way through  you can feel when its gone through.

Cheers

Bryan

Offline Alex

  • Posts: 5285
Re: Cutting Drywall with Vecturo
« Reply #5 on: March 18, 2017, 03:20 AM »
I do this regularly with my MultiMaster and it is very easy to do. I prefer a round blade for this, it is easy to make straight cuts by using a straight edge along the cut line, or drawing a line and free hand it.

Offline Bob D.

  • Posts: 71
Re: Cutting Drywall with Vecturo
« Reply #6 on: March 18, 2017, 07:14 AM »
I've used my Multimaster which I bought 10 years ago and also my cordless RIDGID JobMax to make these types of cuts. I've tried then on occasion but always go back to using my razor knife.

But before I had either of these tools I preferred to use a razor knife over a sheetrock saw as it made less mess and was faster.

Use a straight edge and razor knife I find the easiest to cut precise openings for new wall openings for electrical boxes when installing LAN or other low voltage cabling or for new AC outlets or switches. There is next to no dust created and it takes less time than it does to setup and plug in a power tool.

Give it a try and you'll like it I think.
-----
It's a table saw, do you know where your fingers are?

Offline mattmass

  • Posts: 32
Re: Cutting Drywall with Vecturo
« Reply #7 on: March 18, 2017, 08:08 AM »
Thanks all!

A track saw is exactly what I'd reach for if the drywall wasn't already on the wall :)

I'll give the tried-and-true utility knife a shot. So much for new toys huh [crying]

Offline tjbnwi

  • Posts: 4715
  • Cedar Tucky Indiana
Re: Cutting Drywall with Vecturo
« Reply #8 on: March 18, 2017, 08:16 AM »
Thanks all!

A track saw is exactly what I'd reach for if the drywall wasn't already on the wall :)

I'll give the tried-and-true utility knife a shot. So much for new toys huh [crying]

Why not when drywall is on the wall?

Works on plaster on a ceiling.

Tom

Offline Bob D.

  • Posts: 71
Re: Cutting Drywall with Vecturo
« Reply #9 on: March 18, 2017, 08:21 AM »
I have never tried it but just thinking about it I would not consider
using a track saw for cutting drywall. Way too messy and will kill your
blade plus you risk getting that fine dust in the motor of the saw.

If it's not hung yet then just score and snap like the pros do everyday.
Utility knife, drywall T-square, and a Surform for some fine fitting are
all I have ever needed for 95% of the work.
-----
It's a table saw, do you know where your fingers are?

Offline mattmass

  • Posts: 32
Re: Cutting Drywall with Vecturo
« Reply #10 on: March 18, 2017, 08:25 AM »
Why not when drywall is on the wall?

Works on plaster on a ceiling.

Tom

Hrm. What do use to attach the track?

Offline tjbnwi

  • Posts: 4715
  • Cedar Tucky Indiana
Re: Cutting Drywall with Vecturo
« Reply #11 on: March 18, 2017, 08:29 AM »
I have never tried it but just thinking about it I would not consider
using a track saw for cutting drywall. Way too messy and will kill your
blade plus you risk getting that fine dust in the motor of the saw.

If it's not hung yet then just score and snap like the pros do everyday.
Utility knife, drywall T-square, and a Surform for some fine fitting are
all I have ever needed for 95% of the work.

Cleanest cut you'll ever make in drywall (as long as it's connected to a dust extractor).

I've seen no affect from drywall on the blade, as long as you don't hit a screw.

I've cut 1000's of feet of drywall, plaster and fiber cement products (special blade for plaster and fc), no issues with the saw. I do wipe the base plate and rail down after I've used it on these products.

Tom

Offline tjbnwi

  • Posts: 4715
  • Cedar Tucky Indiana
Re: Cutting Drywall with Vecturo
« Reply #12 on: March 18, 2017, 08:30 AM »
Why not when drywall is on the wall?

Works on plaster on a ceiling.

Tom

Hrm. What do use to attach the track?

Screws through the holes in the ends of the tracks, clamps when possible, 2 side tape-------what ever it takes in the given situation.

Tom

Offline J0hn

  • Posts: 30
Re: Cutting Drywall with Vecturo
« Reply #13 on: March 18, 2017, 11:10 AM »
If your cutting out a piece 5' high and 2' wide, I doubt if you will get it out in one salvageable piece that you can easily reuse.

Chances are it is going to be fastened to the stud (vertically) and your going to have a horizontal joint that only has drywall tape holding the two pieces together.  (So if it is screwed down, you 'might' be able to unscrew it)

Just something to think about

Offline RobBob

  • Posts: 984
Re: Cutting Drywall with Vecturo
« Reply #14 on: March 18, 2017, 11:16 AM »
I have used my Vecturo to cut dry wall and Gladiator plastic slat wall.  Worked well cutting out for electrical outlets, pipes, etc.

I would think a Vecturo blade would have a narrower kerf than a track saw, if that matters.

Try using a round saw blade on the Vecturo but only cut half way through or so and then finish the cut with a dry wall knife.  I think you will have more control over such a large piece and won't be holding a power tool when it begins to come loose .
« Last Edit: March 18, 2017, 02:05 PM by RobBob »

Offline mike_aa

  • Posts: 941
Re: Cutting Drywall with Vecturo
« Reply #15 on: March 18, 2017, 12:09 PM »
Whatever cutting method you choose, if you are worried about hitting screws or nails, run a strong neodymium magnet slowly along your cut line before you make the cut.  It will stick to the screws and show the location.  The picture shows it sticking to an embedded drywall screw in one of our walls.  I don't remember where I got the old surplus ones I have, but you can order them in lots of different shapes and sizes from CMS Magnetics or K&J Magnetics.  This trick also works great to find nails when cutting into a wood floor.

Mike A.

Offline pettyconstruction

  • Posts: 305
Re: Cutting Drywall with Vecturo
« Reply #16 on: March 18, 2017, 12:10 PM »
Like Tom said
Use a track saw, screw the track to the wall and go.
No dust also if you have a Ct

I use my Supercut all the time for drywall ,seems made for that task
Charlie


Sent from my iPhone using Tapatalk Pro

Offline Gjarman12

  • Posts: 70
Re: Cutting Drywall with Vecturo
« Reply #17 on: March 18, 2017, 12:52 PM »
Another vote for the TS55. I have a beater blade I use for this just in case I hit something (screw/nail). Another perk is the depth of cut is easy to figure out.

Offline Bob D.

  • Posts: 71
Re: Cutting Drywall with Vecturo
« Reply #18 on: March 18, 2017, 01:07 PM »
Cleanest cut you'll ever make in drywall (as long as it's connected to a dust extractor).

I've seen no affect from drywall on the blade, as long as you don't hit a screw.

I've cut 1000's of feet of drywall, plaster and fiber cement products (special blade for plaster and fc), no issues with the saw. I do wipe the base plate and rail down after I've used it on these products.

Tom

Like I said never tried it but I'll take you word for it.

Just sounds like it would be hard on the saw.

But I will keep it in mind should I ever find myself in
a situation where I need to make such a cut. Thanks.
-----
It's a table saw, do you know where your fingers are?

Offline rst

  • Posts: 1336
Re: Cutting Drywall with Vecturo
« Reply #19 on: March 18, 2017, 07:55 PM »
I use my Fein supercut with circular blade to cut drywall and end up with minimal dust by using the 92602075018, FEIN Dust extraction device.

Offline Holzhacker

  • Posts: 855
    • www.aic-chicago.com
Re: Cutting Drywall with Vecturo
« Reply #20 on: March 18, 2017, 08:46 PM »
Fein multimaster, hand drywall saw or Trion. I use all depending on situation and what I remembered to put in the truck. If you are good at using your tools you should be fine holding the saw (whichever one) in one hand and holding the vac hose in the other hand near the blade.
I'm fine with using an upcoming job to rationalize buying a new tool. This one is a bit of a stretch though.
"The Code is not a ceiling to reach but a floor to work up from"