Author Topic: lr 32 system/ frameless cabinet  (Read 1375 times)

0 Members and 1 Guest are viewing this topic.

Offline lshah72414

  • Posts: 35
lr 32 system/ frameless cabinet
« on: December 29, 2017, 03:45 PM »
This is my first try with the frameless cabinet using the lr 32 system.
Cabinet is all assembled, drawer is in. Doors do not fit properly.
I have ordered the hardware twice. I am using Blum 170 degree hinges for frameless inset cabinets.
On the side of cabinet I am in 37 mm,  the center of the screws are approximately on a line 38.5 mm inset.
On the door, the recess is 5mm and the start of the hinge is at 2.5-3mm inset.
I have enclosed two photos, one with door open and the other with it closed, and you can see how edge of door is out approximately 18 mm. I have adjusted it in as far as it will go. AM I using the wrong hardware? Did I do something wrong. If I move mounting plate in on side of cabinet I can solve problem, but then what is the good of the lr 32 system if I do that? thank you.

Festool USA does not pre-approve the contents of this website nor endorse the application or use of any Festool product in any way other than in the manner described in the Festool Instruction Manual. To reduce the risk of serious injury and/or damage to your Festool product, always read, understand and follow all warnings and instructions in your Festool product's Instruction Manual. Although Festool strives for accuracy in the website material, the website may contain inaccuracies. Festool makes no representations about the accuracy, reliability, completeness or timeliness of the material on this website or about the results to be obtained from using the website. Festool and its affiliates cannot be responsible for improper postings or your reliance on the website's material. Your use of any material contained on this website is entirely at your own risk. The content contained on this site is provided for informational purposes only and does not constitute professional advice.


Re: lr 32 system/ frameless cabinet
« Reply #1 on: December 29, 2017, 04:06 PM »
I think you will  find you need to have your system holes at 37mm plus the door thickness.
http://go.rockler.com/tech/RTD10301010AA.pdf

Offline lshah72414

  • Posts: 35
Re: lr 32 system/ frameless cabinet
« Reply #2 on: December 29, 2017, 07:31 PM »
@1951CorrectCraft  I believe you are correct. Thank you.

Offline Brian Livingstone

  • Posts: 141
Re: lr 32 system/ frameless cabinet
« Reply #3 on: December 29, 2017, 07:58 PM »
Hi,

Typically frameless cabinets use an overlay hinge, not an inset hinge.

The 37 mm will work with the overlay hinge.

With frameless cabinets you want the door to overlay the frame so that all is visible is the door.  You don’t want to see the frame as you would with the inset hinge.

Inset cabinets are the hallmark of fine cabinetry when using a face frame.

You need to buy a different hinge.

Brian
Kapex, TS75, MFT, OF1010, OF2200, DTS400 REQ, Parallel guide rails, 800, 1080, 1400, 1900, 3000 guide rail, Domino 500, CT36, CT Midi, , RS2E, RO150, Boom Arm, Crown stops, 6 drawer Sortainer, Carvex, Syslite II, Festool safety glasses must start to wear.

Offline lshah72414

  • Posts: 35
Re: lr 32 system/ frameless cabinet
« Reply #4 on: January 02, 2018, 06:49 PM »
Brian,

Thank you for your help. I will remember for my next project.