Author Topic: template routing  (Read 3361 times)

0 Members and 1 Guest are viewing this topic.

Offline clydeb

  • Posts: 3
template routing
« on: April 15, 2017, 03:46 PM »
I am building a 14 foot boat style conference table.  Table is 4 ft in middle and tapers to 40 inches on each end.  Made from cherry that is finished milled or planed to 1 3/4 inches thick.  The edge of the table and both ends will be wraped with fiqured hard maple.  I have made the template and I'm ready to trim the table to shape and apply the maple.  I have made some of these tables in the past and it kills the normal router, last table was 12 ft long and I used my Festool router with a whiteside RD 5200 bit taking 5/16 cuts at a time plus top edge is ragged sometime where the maple mates.  You know the "money shot".  This is a curved cut, but a gentle one.  Any better ideas?  Thank You

Festool USA does not pre-approve the contents of this website nor endorse the application or use of any Festool product in any way other than in the manner described in the Festool Instruction Manual. To reduce the risk of serious injury and/or damage to your Festool product, always read, understand and follow all warnings and instructions in your Festool product's Instruction Manual. Although Festool strives for accuracy in the website material, the website may contain inaccuracies. Festool makes no representations about the accuracy, reliability, completeness or timeliness of the material on this website or about the results to be obtained from using the website. Festool and its affiliates cannot be responsible for improper postings or your reliance on the website's material. Your use of any material contained on this website is entirely at your own risk. The content contained on this site is provided for informational purposes only and does not constitute professional advice.


Offline thudchkr

  • Posts: 67
Re: template routing
« Reply #1 on: April 15, 2017, 10:26 PM »
As long as you are cutting down hill, shouldn't be difficult at all to get a good edge.  I would use a jigsaw first, staying about 1/8" or less, outside the line, and then using the template, take it off in a single pass using the Festool OF 2200 router.  You would have to flip your pieces in order to cut down hill, but this will result in the best cut by far.

Are you using the same templates to cut the hard maple wraps as well?  If so, same method should work for them. 

Clint
Clint

TS 55, TS 75, HKC 55, DF 500, DF 700, Kapex, MFK 700, OF 1400, OF OF 2200, CT 22, ETS 150/3, ETS EQ 150/5, PRO 5, DTS 400, CXS

Offline Holmz

  • Posts: 3998
Re: template routing
« Reply #2 on: April 16, 2017, 01:04 AM »
Just make sure your jigsaw blade doesn't flex to the side.

Offline bionicus

  • Posts: 116
Re: template routing
« Reply #3 on: April 16, 2017, 02:42 AM »
With that gentle of a curve I'd trace the pattern, skip the jigsaw and lop off the bulk of the material with my TS55, quickly repositioning the track as many times as necessary to get within at least 1/4" of the cutline. Then set the template to within an 1/8" and make a first pass with the router to get even closer. Reset to your final dimensions and make the cleanup pass.

Whiteside's Ultimate Pattern Bit (UDFT9112) will handle it. It's a solid carbide large-diameter compression bit. Expensive but works great even with figured woods. Check it out on YouTube.

For a 1-3/4" top you'll actually need to make 2 final passes since the bit is only 1-1/8" in length, first riding along the template then lowered to ride along the finished edge of the table itself. I've only used it in my router table but a powerful handheld should be fine. Keep the RPMs around 15,000.