Author Topic: Woodpecker Hole in Fluted Columns  (Read 2284 times)

0 Members and 1 Guest are viewing this topic.

Offline bigGaloot

  • Posts: 25
Woodpecker Hole in Fluted Columns
« on: September 21, 2014, 12:15 PM »
Well, I went to the clients house to install some custom shutters I had built to replace a few that had rotten, and he walks me over to the main entrance.

202620-0

202622-1

One hole in each column... freshly made.

My question is, what would you folks do, cut a dutchman and carve flutes or use an abatron epoxy? 

Thanks for any responses.


Festool USA does not pre-approve the contents of this website nor endorse the application or use of any Festool product in any way other than in the manner described in the Festool Instruction Manual. To reduce the risk of serious injury and/or damage to your Festool product, always read, understand and follow all warnings and instructions in your Festool product's Instruction Manual. Although Festool strives for accuracy in the website material, the website may contain inaccuracies. Festool makes no representations about the accuracy, reliability, completeness or timeliness of the material on this website or about the results to be obtained from using the website. Festool and its affiliates cannot be responsible for improper postings or your reliance on the website's material. Your use of any material contained on this website is entirely at your own risk. The content contained on this site is provided for informational purposes only and does not constitute professional advice.


Offline carlb40

  • Posts: 370
  • Site carpenter
Re: Woodpecker Hole in Fluted Columns
« Reply #1 on: September 21, 2014, 12:51 PM »
Before any repairs are made i would make sure the woodpecker isn't inside and won't come back? Or you could be there doing repairs very often.  [eek]

For a small hole like that i would probably go with the epoxy, but then i have not had to patch repair columns before.  [wink]
Carl

Never never go, never never know [smile]

Flickr

Offline ewils91

  • Posts: 166
Re: Woodpecker Hole in Fluted Columns
« Reply #2 on: September 21, 2014, 03:48 PM »
We have repaired about a dozen columns over the past 11 years. We have always used a poly glue and Dutchmen, with a little patience and care you can't see the repairs. All of our clients have been very happy with the workmanship. Eleven years later you still can't detect any repair evidence of the first two columns we did. We bade the Dutchmen to stand out a little proud then carefully sanded them to size.I hope this helps.

Eddy Wilson

Offline leakyroof

  • Posts: 2198
Re: Woodpecker Hole in Fluted Columns
« Reply #3 on: September 22, 2014, 04:22 PM »
The base looks like a good candidate for Abratron, and a patch or Dutchman for the fluted section in the main of the column.
Not as many Sanders as PA Floor guy.....

Offline jmarkflesher

  • Posts: 248
  • Scoot
Re: Woodpecker Hole in Fluted Columns
« Reply #4 on: September 22, 2014, 08:04 PM »
Can the owners say if it was a repetitive tapping or was it an irregular tapping. If irregular, tap tap stop tap tap tap stop, It may be a pileated woodpecker, full red crown and could be up to 18" long. MARK
« Last Edit: September 22, 2014, 08:24 PM by jmarkflesher »
DEC 21st, 2012 TIC TIC TIC   WAS A DUD

Offline jobsworth

  • Posts: 5271
  • Does Anyone Know What Time It Is?
Re: Woodpecker Hole in Fluted Columns
« Reply #5 on: November 06, 2014, 02:04 AM »
A little late but Id use bondo