Author Topic: Bathroom vanity  (Read 1750 times)

0 Members and 1 Guest are viewing this topic.

Offline ctvader

  • Posts: 26
Bathroom vanity
« on: June 03, 2018, 07:18 AM »
Building things is a hobby of mine which I hope will turn into something more in the future.  I've built a few things - bookcases, computer desk for my son, etc.  However, this is my first cabinet/vanity that I built for my family - needless to the wife loves it.  All built with 3/4 birch plywood, soft close drawers, painted with Ben Moore WB Satin Impervo (simply white), kreg pocket hole screws for joinery.  All panels cuts done with TS55.  Toe kick cut by hand with a jig saw and a template I drew up.  I went to install it yesterday and couldn't get the cold water shutoff valve to close. 

I owe a ton of thanks to everyone on this board who post their projects and ideas - it gave me the confidence to tackle a project of this magnitude.  My favorite art of this project was what I learned, which will be needed for the next two I build. 

Excuse the curtains in front of the pic - it's sitting in our dining room until the plumber can fix/replace the shutoff valve. 

Festool USA does not pre-approve the contents of this website nor endorse the application or use of any Festool product in any way other than in the manner described in the Festool Instruction Manual. To reduce the risk of serious injury and/or damage to your Festool product, always read, understand and follow all warnings and instructions in your Festool product's Instruction Manual. Although Festool strives for accuracy in the website material, the website may contain inaccuracies. Festool makes no representations about the accuracy, reliability, completeness or timeliness of the material on this website or about the results to be obtained from using the website. Festool and its affiliates cannot be responsible for improper postings or your reliance on the website's material. Your use of any material contained on this website is entirely at your own risk. The content contained on this site is provided for informational purposes only and does not constitute professional advice.


Offline jdm5

  • Posts: 99
Re: Bathroom vanity
« Reply #1 on: June 03, 2018, 07:55 AM »
That looks amazing - really nice job! 
Drank the green Kool-Aid...gave up counting long ago.

Offline neilc

  • Posts: 2511
Re: Bathroom vanity
« Reply #2 on: June 03, 2018, 07:59 AM »
Inset doors and drawers are a challenge to get right.  You did great!  Welcome to FOG!

Offline Don T

  • Posts: 1817
  • Phoenix, Az
Re: Bathroom vanity
« Reply #3 on: June 03, 2018, 09:06 AM »
Great job. Keep up the good work
RO150, C12, DF 500 Q, CT33, TS75, MFT3, Kapex 120, MFT3/Kapex, MFK 700, RO 90, ETS150/3, CT22, Centrotec Installers Kit, Parallel Guides & Ext, Carvex, OF1400, LR32 Set, MFS400 w/700 rails, KA UG Set, First Aid Kit, RTS 400 EQ, Vecturo OS400 Set, CT Wings, CT Drill Guide, Pro 5, CXS, C18, HL850, Vac Sys set

Offline Cheese

  • Posts: 5055
Re: Bathroom vanity
« Reply #4 on: June 03, 2018, 09:35 AM »
Nice job... [thumbs up]...did you spray the Satin Impervo?

Offline ctvader

  • Posts: 26
Re: Bathroom vanity
« Reply #5 on: June 03, 2018, 10:02 AM »
Thanks all for the kind words.  I learned an immense amount, which is what I was after.  For finishing, I brushed two coats of primer, sanding b/t each coat (180grit).  I then applied two coats of the Satin Impervo by brush, sanding b/t each coat (180 —> 220 —> 320 where needed) and then spray a very light coat (homeright hvlp). 

Offline Brian Livingstone

  • Posts: 164
Re: Bathroom vanity
« Reply #6 on: June 03, 2018, 11:24 AM »

Looks really nice !

Did you consider European concealed hinges ?  I use them on inset cabinets.  The clean look is what I am after.

I would have matched the small door handles with matching medium handles on the doors instead of the knobs, and one long matching handle on the false front.  Assymmetrical symmetry.

Again, really nice job !

Brian
Kapex, TS75, MFT, OF1010, OF2200, DTS400 REQ, Parallel guide rails, 800, 1080, 1400, 1900, 3000 guide rail, Domino 500, CT36, CT Midi, , RS2E, RO150, Boom Arm, Crown stops, 6 drawer Sortainer, Carvex, Syslite II, Festool safety glasses must start to wear.

Offline Billedis

  • Posts: 613
Re: Bathroom vanity
« Reply #7 on: June 03, 2018, 12:09 PM »
Beautiful work.  Thanks for sharing.  Bill

Offline jobsworth

  • Posts: 5264
  • Does Anyone Know What Time It Is?
Re: Bathroom vanity
« Reply #8 on: June 03, 2018, 12:17 PM »
Very nicely done

Offline eddomak

  • Posts: 303
Re: Bathroom vanity
« Reply #9 on: June 03, 2018, 10:25 PM »
Thanks all for the kind words.  I learned an immense amount, which is what I was after.

Fantastic job - You can be proud of that! I agree with you - the learning acquired is so valuable as well - each project adds to your skill and experience to make every subsequent project even better and easier. I also love this forum for being able to ask questions have have so many helpful replies. Looking forward to your next project!

P.S. If you like that type of look and projects, definitely check out Ana White's site and YouTube channel.

Offline ctvader

  • Posts: 26
Re: Bathroom vanity
« Reply #10 on: June 04, 2018, 06:21 AM »
The handles and knobs were the wife’s decision.  I suggested something else to achieve the symmetry but was over ruled (all good).  When I do it again, I already have a better way to do the drawers and doors.  The toe kick is  5 1/4, which will tie in to the baseboard in the bathroom, hopefully giving the furniture look.  I’ll post when done.

Offline SilviaS7

  • Posts: 25
Re: Bathroom vanity
« Reply #11 on: June 07, 2018, 07:37 PM »
Very clean, great build.  I'm super jealous.  That paint job is also nice and smooth.  Thanks for sharing!

Offline ultane

  • Posts: 12
Re: Bathroom vanity
« Reply #12 on: July 30, 2018, 01:28 PM »
Very beautiful build. I wish I could do that!


Sent from my iPhone using Tapatalk
I might be wrong… Just ask my X...