Author Topic: Chair Repair with Domino Connectors  (Read 1544 times)

0 Members and 1 Guest are viewing this topic.

Offline Crox G

  • Posts: 89
Chair Repair with Domino Connectors
« on: October 22, 2017, 08:37 PM »
Executive Summary:  Domino connectors pull the chair joints together. 

I've been anxious to find a project for Domino Connectors ever since I saw them in person at Festool Connect at Norfolk (Va.) Woodcraft.  A friend asked me those dreaded words "Do you think you could fix my favorite chair for me?"  I'm a Windsor chair lover (a Mike Dunbar disciple), and believe that all non-Windsor chairs are designed to fall apart.  I agreed to try.


It is a factory-made side chair, held together with mortises and tenons at the tops of the legs.  The tenons are 14mm and look like broad Dominoes.  The glue had failed at the front leg joints, and the chair was wobbly. I wanted to knock it apart, clean the joints, and re-glue it, but I wanted to add something to keep the frame from racking and pulling apart.

I thought an interior frame would give stiffness, and needed a way to draw the chair parts inward in compression.  The Domino Connectors can draw parts together from 1 or 2 mm apart, and that seemed like just what I needed. 

I used 30 mm stock for the parts, leftover pine and poplar.  I first made a curved section to match the inside of the front rail, trimming it close with a spokeshave. 

Using a 3/8" Kreg drill, which steps down to 1/8", I counterbored the front piece to accept 1.5" Kreg screws.  This piece would be fastened tight against the inside of the front rail.  I also drilled for pocket hole screws to draw the side stretcher tight.  I left a 1mm gap between these parts so the pocket holes would draw the side rail inward.

I then roughed out the two fore-and-aft pieces, and used right-angle connectors to connect them to the back rail.  Just for the fun of it, I used the in-line connectors to fasten the frame pieces together.  With my shooting board I trimmed the two new pieces about 1 mm short (see credit card in the gap), leaving a gap to be drawn up later (see after picture).

I then knocked the side rails off the back legs and cleaned those joints.  I snugged up the three frame pieces together, fastened the two rear parts to the rear rail with the gap, and glued the side rails and the front rail together.  I then fastened the front part to the front rail with Kreg screws through the counterbored holes, and to the side rails with pocket screws.  Then--with great satisfaction!--I drew together the rear connectors.  That chair is tight!  The corner blocks went back on with glue and 23 ga. brads from my Green Buddy.

The chair now weighs a ton.  This was a case of gross over-designing, but it was a good excuse to play with the nifty, precise Connectors and my beloved XL700.

Cheers.
CT Midi, ETS 150/3, OF 1400, TS 55, CXS, RO 90, MF-TB, Syslite, necktie, T18 + 3, Carvex PSC 420 EB, Ti15, Domino XL 700, Vecturo

Festool USA does not pre-approve the contents of this website nor endorse the application or use of any Festool product in any way other than in the manner described in the Festool Instruction Manual. To reduce the risk of serious injury and/or damage to your Festool product, always read, understand and follow all warnings and instructions in your Festool product's Instruction Manual. Although Festool strives for accuracy in the website material, the website may contain inaccuracies. Festool makes no representations about the accuracy, reliability, completeness or timeliness of the material on this website or about the results to be obtained from using the website. Festool and its affiliates cannot be responsible for improper postings or your reliance on the website's material. Your use of any material contained on this website is entirely at your own risk. The content contained on this site is provided for informational purposes only and does not constitute professional advice.


Offline Birdhunter

  • Posts: 2172
  • Woodworker, Sportsman, Retired
Re: Chair Repair with Domino Connectors
« Reply #1 on: October 22, 2017, 09:15 PM »
Nice work. I just completed a bed using the connectors. I’m very pleased with the results.
Birdhunter

Offline PreferrablyWood

  • Posts: 881
Re: Chair Repair with Domino Connectors
« Reply #2 on: June 10, 2018, 06:13 AM »
Thanks for showing and documenting your project. I need to repair some wobbley table structures on outdoor funiture and will benefit greatly from the detailed decription of your methods.
RO 150, 850 HL E Planer rustic head standard head angle fence, MFS 400x2, MFS extensions MFS VB 700 x 1 MFS VB 1000 x 2 . CMS GE, sliding fence, VB and 2x VL extension tables, OF 2200, Accessory Set ZS OF 2200 M,36mm 5m antistatik hose, CMS OF+ CMS TS 75 insert modules. SYS-MFT Fixing-Set,  3.5m sleeved hose, Syslite duo, Sys 4 sort 3 x3, Sys Roll, Sys 1 Box x2 , classic Sys 3-Sort 4, classic Sys 3 Sort 6 x2, Sys Cart x3 Systainer 4 x2  as toolbox with selfmade inserts Systainer 5 as toolbox with insert.
Festool 18V HKC 55 Li 5.2 EB Plus FSK 420,FSK 250, Extra blade for the HKC 55 W32.TI 15, CXS 2.6 Ah version, RO 90 DX, PDC 18/4 plus DC UNI FF depth stop chuck,AD 3/8 square socket holder FF chuck, Centrotec Bits; -->Bit holder and bit selection BHS 65 CE TL 24x, ,Bradpoint DB WOOD CE SET ,Zobo (Forstner) D 15-35 CE-Zobo SET ,Masonary/stone bits DB STONE CE Set,Extender BV 150 CE, Countersink QLS D2-8 CE Hook turner HD D18, end centrotec<--.  TS 75 EBQ, PSC 420, OF 1010, RS 300 EQ, CTL Midi, MFT 3, Parf dogs x2pair +Bench dogs x2pair, FS 1080, FS 1900 .  will get Domino DF 700 XL,  CMS insert BS 120 Belt sander.

Offline ProCarpenterRVA

  • Posts: 69
Re: Chair Repair with Domino Connectors
« Reply #3 on: June 11, 2018, 12:53 PM »
Excellent solution and workmanship! I just used the Domino 700 to reattach a leg on a federal side table that the movers had somehow smashed off last year. Very much fun to save it! :-)

Sent from my SM-T230NU using Tapatalk