Author Topic: Drawer organizer for Systainer  (Read 1383 times)

0 Members and 1 Guest are viewing this topic.

Offline Raffes

  • Posts: 1
Drawer organizer for Systainer
« on: October 01, 2017, 05:09 AM »
Hi, i made this yesterday for my Festool drawer Systainer.
What do you think about this. I didn't like kaizen foam so I came up with this. I made this on the CNC but, half way the CNC stopped because it lost vacuum. Took my CNC 20 minutes to do. Maybe you guys know an improvement. This was just an experiment. Thanks

Festool USA does not pre-approve the contents of this website nor endorse the application or use of any Festool product in any way other than in the manner described in the Festool Instruction Manual. To reduce the risk of serious injury and/or damage to your Festool product, always read, understand and follow all warnings and instructions in your Festool product's Instruction Manual. Although Festool strives for accuracy in the website material, the website may contain inaccuracies. Festool makes no representations about the accuracy, reliability, completeness or timeliness of the material on this website or about the results to be obtained from using the website. Festool and its affiliates cannot be responsible for improper postings or your reliance on the website's material. Your use of any material contained on this website is entirely at your own risk. The content contained on this site is provided for informational purposes only and does not constitute professional advice.


Offline Rob-GB

  • Posts: 1017
Re: Drawer organizer for Systainer
« Reply #1 on: October 01, 2017, 06:34 AM »
 [welcome] to the Fog.
I like the simplicity of the idea and glad you had a CNC to do all those holes, that task alone would drive me nuts. [big grin]

Rob.
Problem? No such thing! Only a solution waiting to be found:- RJ

"A $2 guppy swims......" Deke

Offline HarveyWildes

  • Posts: 579
Re: Drawer organizer for Systainer
« Reply #2 on: October 01, 2017, 10:28 AM »
A simple, creative idea that could be layered for deeper systainers.  I like it.  What about Domino sized holes?

Offline SRSemenza

  • Global Moderator
  • *
  • Posts: 7992
  • Finger Lakes Region, NY State , USA
Re: Drawer organizer for Systainer
« Reply #3 on: October 01, 2017, 11:34 AM »
Nice. That basic grid with dowels could be used to attach solid dividers as well. Just use dowels in the bottom edge of the dividers.

Seth

Offline Peter Halle

  • Global Moderator
  • *
  • Posts: 10854
  • Let's Redux / Revive / Rewind / Rollback the FOG!
Re: Drawer organizer for Systainer
« Reply #4 on: October 01, 2017, 11:39 AM »
Welcome to FOG!

Very interesting project.  You wrote that your CNC sopped to loss of vacuum.  Were you thru drilling versus leaving a tiny bottom?  Also how porous your material is may be part of the issue.  Drill a bunch of holes and make thinner probably equates to more porous.  Maybe double side tape on the bottom to a sacrificial piece will cure that issue.

Peter
Disclaimer:  I have been involved with the development of some TSO Products.  I have offered thoughts and ideas freely.  I am not paid but I may receive products during the development process or afterwards.

Offline Gregor

  • Posts: 541
Re: Drawer organizer for Systainer
« Reply #5 on: October 01, 2017, 01:59 PM »
Interesting idea.

Possibly use a fully drilled board for test fitting and find a good layout for the tools that should be fitted - and when a setup has stabilized mill one where only the needed holes are? Would make it into a one-trick pony for that tools though.

Downside of this could be the weight, compared to foam. My drawer systainers are mostly on the heavy side already.

Offline Michael Kellough

  • Posts: 2956
Re: Drawer organizer for Systainer
« Reply #6 on: October 01, 2017, 03:20 PM »
Lost vacuum...Next time try pausing the drilling process halfway through and put tape over the already cut holes.

Offline fritter63

  • Posts: 1342
Re: Drawer organizer for Systainer
« Reply #7 on: October 09, 2017, 11:34 PM »
Next time don't use vacuum. Cut from oversized stock and program in tabs when cutting outside contour.