Author Topic: New saw in shop and making some jig  (Read 2573 times)

0 Members and 1 Guest are viewing this topic.

Offline Tommy66

  • Posts: 23
    • Blog on Byggebolig.no
New saw in shop and making some jig
« on: May 27, 2017, 06:59 PM »
Fritz and franz
Clamp
Festool : TS55 * OF1010 * EHL65 * Toolbox sys TB-1 * Sys 4 TL * Sys roll-100 *CTL-26 * CXS-SET-DF * DF 500Q-SET * DS 4/5/6/8/10 1060x BU * Sys 2 TL *KAPEX KS 120 * Hammer A3 31 Silent power * Felder FB 510 * Minimax SC3W *
http://www.youtube.com/channel/UCf1_tvcZEeezrOJZN-6v_pQ

Festool USA does not pre-approve the contents of this website nor endorse the application or use of any Festool product in any way other than in the manner described in the Festool Instruction Manual. To reduce the risk of serious injury and/or damage to your Festool product, always read, understand and follow all warnings and instructions in your Festool product's Instruction Manual. Although Festool strives for accuracy in the website material, the website may contain inaccuracies. Festool makes no representations about the accuracy, reliability, completeness or timeliness of the material on this website or about the results to be obtained from using the website. Festool and its affiliates cannot be responsible for improper postings or your reliance on the website's material. Your use of any material contained on this website is entirely at your own risk. The content contained on this site is provided for informational purposes only and does not constitute professional advice.


Offline Tommy66

  • Posts: 23
    • Blog on Byggebolig.no
Re: New saw in shop and making some jig
« Reply #1 on: May 27, 2017, 07:00 PM »
Festool : TS55 * OF1010 * EHL65 * Toolbox sys TB-1 * Sys 4 TL * Sys roll-100 *CTL-26 * CXS-SET-DF * DF 500Q-SET * DS 4/5/6/8/10 1060x BU * Sys 2 TL *KAPEX KS 120 * Hammer A3 31 Silent power * Felder FB 510 * Minimax SC3W *
http://www.youtube.com/channel/UCf1_tvcZEeezrOJZN-6v_pQ

Offline Tommy66

  • Posts: 23
    • Blog on Byggebolig.no
Re: New saw in shop and making some jig
« Reply #2 on: May 27, 2017, 07:04 PM »
Minimax SC3W 2005 mod
Festool : TS55 * OF1010 * EHL65 * Toolbox sys TB-1 * Sys 4 TL * Sys roll-100 *CTL-26 * CXS-SET-DF * DF 500Q-SET * DS 4/5/6/8/10 1060x BU * Sys 2 TL *KAPEX KS 120 * Hammer A3 31 Silent power * Felder FB 510 * Minimax SC3W *
http://www.youtube.com/channel/UCf1_tvcZEeezrOJZN-6v_pQ

Offline Bob D.

  • Posts: 592
Re: New saw in shop and making some jig
« Reply #3 on: May 27, 2017, 07:39 PM »
Beautiful saw, I hope it gives you many years of good service.

If I could ask what is the articulated arm suspended from the ceiling for?

-----
It's a table saw, do you know where your fingers are?

Offline Tommy66

  • Posts: 23
    • Blog on Byggebolig.no
Re: New saw in shop and making some jig
« Reply #4 on: May 27, 2017, 07:43 PM »
Its for the camera.
Festool : TS55 * OF1010 * EHL65 * Toolbox sys TB-1 * Sys 4 TL * Sys roll-100 *CTL-26 * CXS-SET-DF * DF 500Q-SET * DS 4/5/6/8/10 1060x BU * Sys 2 TL *KAPEX KS 120 * Hammer A3 31 Silent power * Felder FB 510 * Minimax SC3W *
http://www.youtube.com/channel/UCf1_tvcZEeezrOJZN-6v_pQ

Offline Bob D.

  • Posts: 592
Re: New saw in shop and making some jig
« Reply #5 on: May 27, 2017, 07:44 PM »
I thought it might be but figured I would ask. Thank you.
-----
It's a table saw, do you know where your fingers are?

Offline Tommy66

  • Posts: 23
    • Blog on Byggebolig.no
Re: New saw in shop and making some jig
« Reply #6 on: May 28, 2017, 10:22 PM »
Fritz and franz get the mm
Festool : TS55 * OF1010 * EHL65 * Toolbox sys TB-1 * Sys 4 TL * Sys roll-100 *CTL-26 * CXS-SET-DF * DF 500Q-SET * DS 4/5/6/8/10 1060x BU * Sys 2 TL *KAPEX KS 120 * Hammer A3 31 Silent power * Felder FB 510 * Minimax SC3W *
http://www.youtube.com/channel/UCf1_tvcZEeezrOJZN-6v_pQ

Offline Tommy66

  • Posts: 23
    • Blog on Byggebolig.no
Re: New saw in shop and making some jig
« Reply #7 on: August 26, 2017, 12:50 PM »
Festool : TS55 * OF1010 * EHL65 * Toolbox sys TB-1 * Sys 4 TL * Sys roll-100 *CTL-26 * CXS-SET-DF * DF 500Q-SET * DS 4/5/6/8/10 1060x BU * Sys 2 TL *KAPEX KS 120 * Hammer A3 31 Silent power * Felder FB 510 * Minimax SC3W *
http://www.youtube.com/channel/UCf1_tvcZEeezrOJZN-6v_pQ

Offline bigmoguls

  • Posts: 15
Re: New saw in shop and making some jig
« Reply #8 on: August 28, 2017, 04:57 PM »
Very nice.