HowardH
 Offline
Location: Plano, Tx Member Since: Jan 2007
Posts: 704
|
 |
« on: December 30, 2007, 02:47 PM » |
|
This project had been on the to do list for some time but with the addition of the RTS 400 from Santa, it became more urgent. So using some left over mdf, 1/2" and some oak for the trim, I made this yesterday to house all my abrasives. The larger slots are for the 150mm RO abrasives and the small ones are for the RTS 400. Left some room for future expansion. It was a fun project.  |
|
|
|
|
Logged
|
Howard H
The Plano Texas Festool Fanatic!
Shelby Metcalf, basketball coach at Texas A&M, recounting what he told a player who received four F's and one D: "Son, looks to me like you're spending too much time on one subject."
mft1080, T15, RO150FEQ, TS55, RTS400, ETS 150/3, OF1400, CT22, CT33, MFS 400 & 700, Boom Arm, 800, 1080, 1400, 1900 rails CSX drill Qwas dogs
|
|
|
Festool USA does not pre-approve the contents of this website nor endorse the application or use of any Festool product in any way other than in the manner described in the Festool Instruction Manual. To reduce the risk of serious injury and/or damage to your Festool product, always read, understand and follow all warnings and instructions in your Festool product's Instruction Manual. Although Festool strives for accuracy in the website material, the website may contain inaccuracies. Festool makes no representations about the accuracy, reliability, completeness or timeliness of the material on this website or about the results to be obtained from using the website. Festool and its affiliates cannot be responsible for improper postings or your reliance on the website's material. Your use of any material contained on this website is entirely at your own risk. The content contained on this site is provided for informational purposes only and does not constitute professional advice.
|
|
Eli
Offline
Location: Melbourne, Australia Member Since: Jul 2007
Posts: 2480
A Yankee in Kangaroo Court
|
|
« Reply #1 on: December 30, 2007, 05:09 PM » |
|
That is easily the nicest sandpaper rack I've ever seen, by a very long margin. The abrasives almost bring it down.
|
|
|
|
|
Logged
|
Do nothing, stay ahead.
|
|
|
Matthew Schenker
Offline
Location: UNITED STATES (US) Member Since: Jan 2007
Posts: 2624
|
|
« Reply #2 on: December 30, 2007, 05:34 PM » |
|
Howard,
That's good. My shop could certainly benefit from something like that. As I added more Festool sanders to my tool collection over the past couple of years (six at the moment) the collection of different Festool abrasives grew along with it. Thjere was a time when stacking the boxes of abrasives on my shop bookshelf was not a bad solution, but it's getting to be a royal pain. I need to build something like what you have shown us.
Thanks for sharing your idea, and for motivating me to move on this!
Matthew
|
|
|
|
|
Logged
|
|
|
|
HowardH
Offline
Location: Plano, Tx Member Since: Jan 2007
Posts: 704
|
|
« Reply #3 on: December 30, 2007, 07:07 PM » |
|
Thanks guys for the kind words. It would have been easier to just place an order with Uncle Bob for an abrasives systainer but I don't have any room left in my shop made sysport. My original plan, I must admit, wasn't quite so elaborate with the oak trim. I thought it was done with just the box but then my wife came out to the garage and asked why I didn't have it finished. Oops. Got busy with the oak. That leaves a question that I think may have been asked before but I don't remember. Once I planed the oak to the desired thickness and then ripped the board into several "sticks" to the width I wanted, I couldn't think of a way to use my MFT to cross cut the individual pieces that make up the trim. Ended up using my table saw and sled. How does one cut very small (5-6") lengths on such small stock using the MFT and TS55?
|
|
|
|
|
Logged
|
Howard H
The Plano Texas Festool Fanatic!
Shelby Metcalf, basketball coach at Texas A&M, recounting what he told a player who received four F's and one D: "Son, looks to me like you're spending too much time on one subject."
mft1080, T15, RO150FEQ, TS55, RTS400, ETS 150/3, OF1400, CT22, CT33, MFS 400 & 700, Boom Arm, 800, 1080, 1400, 1900 rails CSX drill Qwas dogs
|
|
|
Eli
Offline
Location: Melbourne, Australia Member Since: Jul 2007
Posts: 2480
A Yankee in Kangaroo Court
|
|
« Reply #4 on: December 30, 2007, 09:32 PM » |
|
A question for the ages.
|
|
|
|
|
Logged
|
Do nothing, stay ahead.
|
|
|
jonny round boy
 Online
Location: West Yorkshire, UK Member Since: Jul 2007
Posts: 2102
|
|
« Reply #5 on: December 30, 2007, 10:16 PM » |
|
How does one cut very small (5-6") lengths on such small stock using the MFT and TS55?
You don't - that's what the Kapex is for....  |
|
|
|
|
Logged
|
Festoolian since February 2006
TS55R EBQ saw - CTL26 - CTL Mini - OF1400EBQ router - KS120 Kapex SCMS - ETS150/3 sander - RO90 sander - DF500 Domino - T12 drill
Wish list (in no particular order!): Anything not listed above....
|
|
|
mot
Offline
Location: Canada Member Since: Feb 2007
Posts: 48
|
|
« Reply #6 on: December 30, 2007, 10:25 PM » |
|
That's a good idea. I have to hunt for mine all the time. They sit in boxes in various locations in the shop. Thanks for posting this.
|
|
|
|
|
Logged
|
|
|
|
Eli
Offline
Location: Melbourne, Australia Member Since: Jul 2007
Posts: 2480
A Yankee in Kangaroo Court
|
|
« Reply #7 on: December 30, 2007, 10:58 PM » |
|
How does one cut very small (5-6") lengths on such small stock using the MFT and TS55?
You don't - that's what the Kapex is for.... That was cheap and gratuitous but I almost enjoy it more when you do it! |
|
|
|
|
Logged
|
Do nothing, stay ahead.
|
|
|
Brice Burrell
Online
Location: Pittsburgh, PA, USA Member Since: Mar 2007
Posts: 6212
Remodeling Contractor
|
 |
« Reply #8 on: December 30, 2007, 11:28 PM » |
|
How does one cut very small (5-6") lengths on such small stock using the MFT and TS55?
You don't - that's what the Kapex is for.... That was cheap and gratuitous but I almost enjoy it more when you do it! Yeah, I'm laughing my butt off!  |
|
|
|
« Last Edit: December 30, 2007, 11:31 PM by Brice Burrell »
|
Logged
|
|
|
|
|
