Author Topic: Three custom tables  (Read 873 times)

0 Members and 1 Guest are viewing this topic.

Offline fignewton

  • Posts: 65
  • "Fine Quality Sawdust"
Three custom tables
« on: October 05, 2017, 01:32 PM »
Had a customer ask me about making some tables for him.  His family has a place on the coast and they collect "sea glass" that washes up on the beach.  He had a table already that someone made that was a prototype for the idea (picture below).  The tables' aprons, legs, and tops are made of 2 x 3 and 2 x 4 actual ash (lots of planing!) to be sturdy and get the depth he wanted.  Inside the apron is a set of cleats upon which will rest a frosted panel of translucent Plexiglas, on which the sea glass is laid.  A 1/2 plywood bottom is screwed into the cleats from below, and LED strips sit on the bottom under the Plexiglas for back-lighting.  The tops are routed 3/8 x 3/8 for inset glass.  The plywood bottom, and the shelf below have center holes.  He'll run his extension cord under the table, then up through the shelf and a basket which goes on the shelf, through the bottom and out to the LED strips.  The big table is 54 x 30, and the other two are a 28 square and a 28 x 34 rectangle.  I think I used all of my Festool toys on this project.
I started with raw ash, used the TS55 to get my first edge (multiple passes, given the thickness), then to the rough lengths on the Kapex.  Joiner, then planer, then table saw for ripping.  Used 4 10 x 50mm dominoes for leg/apron joinery, and 2 each in the top joinery.  Leg stretchers were put in from the bottom with pocket screws so they could be removed for pre-drilling the countersunk holes for the lag screws that hold the top to the apron.  Had to do this going in from the bottom, since you'd see inside the table opening.  RO125 used for all sanding, C12 and hole saw for 3" holes.  OF1400 and a rabbetting bit for routing the rabbets for the glass.  Finally, MFK700 for 1/8th roundover on sharp edges of the tops.  The ash was really beautiful.  This was a fun project, but a little hard to work 3 at one time.  He's going to stain, and hopefully will send me finished pics with sea glass in them.
TS55, MFT3+, OF1400, C12, CT-26, LR-32 system, Domino 500, RO125, MFK 700, Carvex w/ accsy, Sys-roll,  CXS, Kapex, UG with extensions, RO90

Festool USA does not pre-approve the contents of this website nor endorse the application or use of any Festool product in any way other than in the manner described in the Festool Instruction Manual. To reduce the risk of serious injury and/or damage to your Festool product, always read, understand and follow all warnings and instructions in your Festool product's Instruction Manual. Although Festool strives for accuracy in the website material, the website may contain inaccuracies. Festool makes no representations about the accuracy, reliability, completeness or timeliness of the material on this website or about the results to be obtained from using the website. Festool and its affiliates cannot be responsible for improper postings or your reliance on the website's material. Your use of any material contained on this website is entirely at your own risk. The content contained on this site is provided for informational purposes only and does not constitute professional advice.


Offline JCLP

  • Posts: 734
Re: Three custom tables
« Reply #1 on: October 05, 2017, 03:50 PM »
Beautiful craftmenship and tables. Can't wait to see the finish product.

JC

Offline montyss

  • Posts: 22
Re: Three custom tables
« Reply #2 on: October 05, 2017, 04:24 PM »
That's Great work ! Looks amazing

Offline Jasonj888

  • Posts: 94
    • Blog about woodworking and family life.
Re: Three custom tables
« Reply #3 on: October 06, 2017, 03:16 PM »
Nice work. I can't imagine making it all out of ash - some seriously hard wood. I would love to see a picture when it's filled with sea glass.