Author Topic: Veg Trug type planter for my wife...  (Read 13494 times)

0 Members and 1 Guest are viewing this topic.

Offline SittingElf

  • Posts: 1374
  • 66 Systainers and rising! YIKES!
Re: Veg Trug type planter for my wife...
« Reply #30 on: May 26, 2015, 10:38 AM »
After looking at others I copied as best I could.  Wife doesn't know these exist yet, was able to get them done while she is gone for a couple of weeks.  She will have to decide on the placement on the patio, then we will put the liners in and fill them.  I used Cedar fence pickets for the spaced interior boards, ripped them down with the TS55.

(Attachment Link) (Attachment Link) (Attachment Link) (Attachment Link)

Happy to see I've started a trend! [big grin]

As for yours, the regular design calls for another spacing at the bottom of the side rails to allow for water drainage without pooling. (Look at my build at the inside bottom cross beam.  You can still salvage yours I think, by drilling some holes in the 2X4 cross beam.  Pooling that lingers might cause the cross beam to warp or rot quickly.  Otherwise...VERY NICE builds, and your wife will love them!

For those building to approximately the same dimensions, you can buy the pre-formed liner through Amazon at the following link. Cheap and saves a hassle of trying to work with a roll to fit. The link is for the full size Trug...the same as I and others built. (Yes, the picture shows the smaller size, but the liner is for the larger version)

http://www.amazon.com/Compact-VegTrug-Planter-Replacement-Liner/dp/B00EOW6NU6

Cheers,
Frank

Woodworking is 3% talent and 97% paying attention to the FOG! 

hammerfelderowners.com

Festool USA does not pre-approve the contents of this website nor endorse the application or use of any Festool product in any way other than in the manner described in the Festool Instruction Manual. To reduce the risk of serious injury and/or damage to your Festool product, always read, understand and follow all warnings and instructions in your Festool product's Instruction Manual. Although Festool strives for accuracy in the website material, the website may contain inaccuracies. Festool makes no representations about the accuracy, reliability, completeness or timeliness of the material on this website or about the results to be obtained from using the website. Festool and its affiliates cannot be responsible for improper postings or your reliance on the website's material. Your use of any material contained on this website is entirely at your own risk. The content contained on this site is provided for informational purposes only and does not constitute professional advice.


Offline groveb

  • Posts: 27
Re: Veg Trug type planter for my wife...
« Reply #31 on: May 26, 2015, 10:45 AM »
After looking at others I copied as best I could.  Wife doesn't know these exist yet, was able to get them done while she is gone for a couple of weeks.  She will have to decide on the placement on the patio, then we will put the liners in and fill them.  I used Cedar fence pickets for the spaced interior boards, ripped them down with the TS55.

(Attachment Link) (Attachment Link) (Attachment Link) (Attachment Link)

Happy to see I've started a trend! [big grin]

As for yours, the regular design calls for another spacing at the bottom of the side rails to allow for water drainage without pooling. (Look at my build at the inside bottom cross beam.  You can still salvage yours I think, by drilling some holes in the 2X4 cross beam.  Pooling that lingers might cause the cross beam to warp or rot quickly.  Otherwise...VERY NICE builds, and your wife will love them!

For those building to approximately the same dimensions, you can buy the pre-formed liner through Amazon at the following link. Cheap and saves a hassle of trying to work with a roll to fit. The link is for the full size Trug...the same as I and others built. (Yes, the picture shows the smaller size, but the liner is for the larger version)

http://www.amazon.com/Compact-VegTrug-Planter-Replacement-Liner/dp/B00EOW6NU6

Cheers,
Frank


Frank,

Thanks for the heads up, I didn't catch that detail, shouldn't be too hard to fix at this point.

Offline groveb

  • Posts: 27
Re: Veg Trug type planter for my wife...
« Reply #32 on: May 26, 2015, 11:23 AM »
After looking at others I copied as best I could.  Wife doesn't know these exist yet, was able to get them done while she is gone for a couple of weeks.  She will have to decide on the placement on the patio, then we will put the liners in and fill them.  I used Cedar fence pickets for the spaced interior boards, ripped them down with the TS55.

(Attachment Link) (Attachment Link) (Attachment Link) (Attachment Link)

Happy to see I've started a trend! [big grin]

As for yours, the regular design calls for another spacing at the bottom of the side rails to allow for water drainage without pooling. (Look at my build at the inside bottom cross beam.  You can still salvage yours I think, by drilling some holes in the 2X4 cross beam.  Pooling that lingers might cause the cross beam to warp or rot quickly.  Otherwise...VERY NICE builds, and your wife will love them!

For those building to approximately the same dimensions, you can buy the pre-formed liner through Amazon at the following link. Cheap and saves a hassle of trying to work with a roll to fit. The link is for the full size Trug...the same as I and others built. (Yes, the picture shows the smaller size, but the liner is for the larger version)

http://www.amazon.com/Compact-VegTrug-Planter-Replacement-Liner/dp/B00EOW6NU6

Cheers,
Frank


Frank,

I bought my liners from DR Equipment

https://www.drpower.com/shop-by-category/gardening/gardening/vegtrug---replacement-liner---medium-1-8m.axd

$10.99 before shipping, shipping isn't too bad if you are buying multiples.

Offline groveb

  • Posts: 27
Re: Veg Trug type planter for my wife...
« Reply #33 on: May 27, 2015, 07:41 AM »
After looking at others I copied as best I could.  Wife doesn't know these exist yet, was able to get them done while she is gone for a couple of weeks.  She will have to decide on the placement on the patio, then we will put the liners in and fill them.  I used Cedar fence pickets for the spaced interior boards, ripped them down with the TS55.

(Attachment Link) (Attachment Link) (Attachment Link) (Attachment Link)

Happy to see I've started a trend! [big grin]

As for yours, the regular design calls for another spacing at the bottom of the side rails to allow for water drainage without pooling. (Look at my build at the inside bottom cross beam.  You can still salvage yours I think, by drilling some holes in the 2X4 cross beam.  Pooling that lingers might cause the cross beam to warp or rot quickly.  Otherwise...VERY NICE builds, and your wife will love them!

For those building to approximately the same dimensions, you can buy the pre-formed liner through Amazon at the following link. Cheap and saves a hassle of trying to work with a roll to fit. The link is for the full size Trug...the same as I and others built. (Yes, the picture shows the smaller size, but the liner is for the larger version)

http://www.amazon.com/Compact-VegTrug-Planter-Replacement-Liner/dp/B00EOW6NU6

Cheers,
Frank


Frank,

Thanks for the heads up, I didn't catch that detail, shouldn't be too hard to fix at this point.

I think the solution will be to wedge some plastic shims between the bottom 1x4 and the pieces of cedar sitting on top of it.  I tried that last night and it created a nice 1/4" gap that should allow water to drain out from that area.

Offline Billy D

  • Posts: 14
Re: Veg Trug type planter for my wife...
« Reply #34 on: April 13, 2017, 12:14 PM »
Old topic - Gonna be my first - Have 30 days to build and deploy for the Mothers Day - Do I build extra for Ma as well as Mama?  [unsure]

If you order the liners from Williams Sonoma - and use the coupon code "EGGHUNT" - 20% off and free shipping - 25$ for 2 shipped to your door.

http://www.williams-sonoma.com/products/vegtrug-raised-bed-liners-medium/?pkey=e%7Cvegtrug%7C30%7Cbest%7C0%7C1%7C24%7C%7C7&cm_src=PRODUCTSEARCH

Thanks to all of you that previously posted! Great work!

Offline lunchman

  • Posts: 74
Re: Veg Trug type planter for my wife...
« Reply #35 on: April 13, 2017, 10:21 PM »
Old topic - Gonna be my first - Have 30 days to build and deploy for the Mothers Day - Do I build extra for Ma as well as Mama?  [unsure]

If you order the liners from Williams Sonoma - and use the coupon code "EGGHUNT" - 20% off and free shipping - 25$ for 2 shipped to your door.

http://www.williams-sonoma.com/products/vegtrug-raised-bed-liners-medium/?pkey=e%7Cvegtrug%7C30%7Cbest%7C0%7C1%7C24%7C%7C7&cm_src=PRODUCTSEARCH

Thanks to all of you that previously posted! Great work!

Yes, build more than one!

I saw this thread when first posted, thought I'd have time to build one but with too many other projects ongoing, decided to buy one. My wife was delighted and put it to good use the first summer, however one wasn't enough. So now she has two (also purchased).

Ordered the first from Williams-Sonoma, and decided to get the covers at the same time. The frame only comes with the greenhouse cover, the other two (insect and frost) require that frame. One of the items was back-ordered, when it finally arrived, I opened the package to find some sort of indoor curtain. Umm, not quite. Sent it back, got something totally unrelated to VegTrug the next time. Sent that back, got a duplicate of one of the covers I already had. At this point, I gave up, they told me to simply keep it.

Ordered the correct cover and VegTrug #2 from Gardener's Supply in Vermont.  The wood color differs from VegTrug #1 but my wife doesn't care. Oddly enough, she still hasn't used any of the covers. Figures.

In winter they're covered with tarps, she's anxious to get going with planting pretty soon.

Offline nappys

  • Posts: 1
Re: Veg Trug type planter for my wife...
« Reply #36 on: April 18, 2017, 10:28 PM »
I agree...thanks Frank for the motivation.  Unfortunately, I did not take build pictures...rookie mistake.  However, here is my version about 95% complete.  My wife cannot wait to use it, and my sister-in-law and mother-in-law are waiting patiently for theirs [eek]

262053-0
262055-1
262057-2

Online Holmz

  • Posts: 3484
Re: Veg Trug type planter for my wife...
« Reply #37 on: April 19, 2017, 05:23 AM »
I agree...thanks Frank for the motivation.  Unfortunately, I did not take build pictures...rookie mistake.  However, here is my version about 95% complete.  My wife cannot wait to use it, and my sister-in-law and mother-in-law are waiting patiently for theirs [eek]

...

Well - Still time for the drawings then ;)

[hiding monitor from Haus-Boss' view]

Offline Bob D.

  • Posts: 194
Re: Veg Trug type planter for my wife...
« Reply #38 on: April 19, 2017, 07:22 AM »
@SittingElf  - Frank you inspired me to promise the boss her raised-bed Mother's Day gift (What do you give when you neglect to have the gift in time?.?.? An IOU!) would be ready to plant by Memorial Day, just made it...

The boss wanted a 2 tier planter, so I went with 2 narrower troughs. Planning Phase:

(Attachment Link)

(Attachment Link)

(Attachment Link)

Dry fit:

(Attachment Link)

The peanut gallery (a pair of nesting gold crested night herons):

(Attachment Link)

Test fit:

(Attachment Link)

Final product:

(Attachment Link)

I neglected to get a photo but the legs are tied together with thru-bolted trestles. It all breaks down for storage in the winter. SWMBO is happy, & along with the MIL is out playing in the dirt right now.

Mission accomplished!

RMW

All the planters are very nicely done. Rich, you said yours breaks down for winter storage. I take it the planter troughs lift off and the legs look like they fold up is that correct? Something like that would work out well on our deck. Wife would love it I'm sure. I was thinking of using cedar as its plentiful in these parts, cheap, and resists rot, what wood has everyone else used?
-----
It's a table saw, do you know where your fingers are?