Woodworking & Power Tools Forum - Festool Owners Group > GENERAL DISCUSSIONS > Member Projects > Small Mobile Work Table / Kapex Stand
Pages: [1]   Go Down
« previous next »
  Print  
Author Topic: Small Mobile Work Table / Kapex Stand  (Read 5323 times)
0 Members and 1 Guest are viewing this topic.
jonny round boy

Offline Offline

Location: West Yorkshire, UK
Member Since: Jul 2007
Posts: 2096
« on: December 21, 2007, 04:16 AM »
Further to my original post, I have now built my work table.

Firstly, apologies to Brice - I had fully intended to photograph every stage of the build,and write an article for his website, but I'd got half way through it before I remembered. Sorry mate.

I picked up a couple of sheets of 18mm WBP hardwood ply (one 6'x2' long grain, one 4'x2' cross-grain) on Wednesday evening, and built the table yesterday. I had tried to get a decent birch ply, but the only place that stocked it locally wanted 70GBP for an 8'x4' sheet...

Here are a couple of views of the finished item:





And with some systainers installed:



Using the MFT top allows the MFT-SP clamps to be used:



Or alternatively the standard clamps can also be used (even with the systainers in, there's still room to fit the clamps):



With the sacrificial MFT top removed, you can see the frame underneath:
Logged
Festoolian since February 2006

TS55R EBQ saw - CTL26 - CTL Mini - OF1400EBQ router - KS120 Kapex SCMS - ETS150/3 sander - RO90 sander - DF500 Domino - T12 drill

Wish list (in no particular order!): Anything not listed above....
Festool USA does not pre-approve the contents of this website nor endorse the application or use of any Festool product in any way other than in the manner described in the Festool Instruction Manual. To reduce the risk of serious injury and/or damage to your Festool product, always read, understand and follow all warnings and instructions in your Festool product's Instruction Manual. Although Festool strives for accuracy in the website material, the website may contain inaccuracies. Festool makes no representations about the accuracy, reliability, completeness or timeliness of the material on this website or about the results to be obtained from using the website. Festool and its affiliates cannot be responsible for improper postings or your reliance on the website's material. Your use of any material contained on this website is entirely at your own risk. The content contained on this site is provided for informational purposes only and does not constitute professional advice.

jonny round boy

Offline Offline

Location: West Yorkshire, UK
Member Since: Jul 2007
Posts: 2096
« Reply #1 on: December 21, 2007, 04:24 AM »
And, continuing:

It's other main function is as a stand for using and transporting the Kapex:





As you can see from these shots, the Kapex sits entirely within the footprint of the table, thus reducing the possibility of catching the saw on doorframes etc when moving from room to room.



Total costs for this project are as follows (all prices in GBP):

3" locking castors, set of 4 = 25.00 (from Screwfix)
Plywood = 25.00
Softwood edging = 5.00
MFT 1080 top = 53.50

Bringing the total cost to 108.50, which in the world of Festool is actually quite cheap!!!

I did alter the dimensions slightly from my original drawing, mainly to match the width of the MFT top. I'll post details of the final drawings/cutlist later if anyone's interested.
Logged
Festoolian since February 2006

TS55R EBQ saw - CTL26 - CTL Mini - OF1400EBQ router - KS120 Kapex SCMS - ETS150/3 sander - RO90 sander - DF500 Domino - T12 drill

Wish list (in no particular order!): Anything not listed above....
Anthony
Festool Dealer

Offline Offline

Location: Melbourne Australia
Member Since: Mar 2007
Posts: 123


Feel a bit like Rocko


WWW
« Reply #2 on: December 21, 2007, 04:35 AM »
Are you sure you built it? It has a barcode on the side!

Just kidding, nice unit. Is it the same height as a MFT800?
Logged
Regards,
Anthony

Festool Shop Owner

IDEAL TOOLS (Australia)
http://www.idealtools.com.au
chippy31

Offline Offline

Location: Belfast Northern Ireland
Member Since: Jul 2007
Posts: 22
« Reply #3 on: December 21, 2007, 05:47 AM »
Lovely job Jonny, does the saw fit inside the stand.
Logged
Anthony
Festool Dealer

Offline Offline

Location: Melbourne Australia
Member Since: Mar 2007
Posts: 123


Feel a bit like Rocko


WWW
« Reply #4 on: December 21, 2007, 05:56 AM »
Quote from: chippy31 on December 21, 2007, 05:47 AM
Lovely job Jonny, does the saw fit inside the stand.

That'edbecool!

Then add a slid in tray, under the perforated top, to keep the dust from getting on the KAPEX when stored inside.
Logged
Regards,
Anthony

Festool Shop Owner

IDEAL TOOLS (Australia)
http://www.idealtools.com.au
jonny round boy

Offline Offline

Location: West Yorkshire, UK
Member Since: Jul 2007
Posts: 2096
« Reply #5 on: December 21, 2007, 05:58 AM »
Quote from: Anthony on December 21, 2007, 04:35 AM
Is it the same height as a MFT800?

No, it's quite a bit lower, I think (I don't know what height the MFT's are).

It's 653mm high overall. That may seem an odd measurement to choose, but it's designed to be the same height as a sys4 and a sys3 on a roll board, so my stacks can be used either side as additional support for long items. Also, with the kapex on, adding a sys1 to the stack brings that up to the same height as the kapex's bed.



Chippy - no, the kapex doesn't fit inside. It wasn't designed to - the inside is for storing systainers.
Logged
Festoolian since February 2006

TS55R EBQ saw - CTL26 - CTL Mini - OF1400EBQ router - KS120 Kapex SCMS - ETS150/3 sander - RO90 sander - DF500 Domino - T12 drill

Wish list (in no particular order!): Anything not listed above....
Anthony
Festool Dealer

Offline Offline

Location: Melbourne Australia
Member Since: Mar 2007
Posts: 123


Feel a bit like Rocko


WWW
« Reply #6 on: December 21, 2007, 06:03 AM »
Quote from: jonny round boy on December 21, 2007, 05:58 AM
Quote from: Anthony on December 21, 2007, 04:35 AM
Is it the same height as a MFT800?

No, it's quite a bit lower, I think (I don't know what height the MFT's are).

It's 653mm high overall. That may seem an odd measurement to choose, but it's designed to be the same height as a sys4 and a sys3 on a roll board, so my stacks can be used either side as additional support for long items.

Fair enough, and good idea.
Logged
Regards,
Anthony

Festool Shop Owner

IDEAL TOOLS (Australia)
http://www.idealtools.com.au
chippy31

Offline Offline

Location: Belfast Northern Ireland
Member Since: Jul 2007
Posts: 22
« Reply #7 on: December 21, 2007, 06:12 AM »
I wasn`t getting what the systainers were for. The FOG has cleared. D 
Logged
jonny round boy

Offline Offline

Location: West Yorkshire, UK
Member Since: Jul 2007
Posts: 2096
« Reply #8 on: December 21, 2007, 07:43 AM »
The main reason that the Kapex won't fit inside, is that the back board is set in, leaving only 400mm internal depth for the systainers. This allows a recess at the rear which is used for storing clamps:
Logged
Festoolian since February 2006

TS55R EBQ saw - CTL26 - CTL Mini - OF1400EBQ router - KS120 Kapex SCMS - ETS150/3 sander - RO90 sander - DF500 Domino - T12 drill

Wish list (in no particular order!): Anything not listed above....
Corwin

Offline Offline

Location: Washington State, USA
Member Since: Jan 2007
Posts: 1995
« Reply #9 on: December 21, 2007, 07:45 PM »
Oh, now I'm really liking your stand!
Logged
Shirt Size:  L
jonny round boy

Offline Offline

Location: West Yorkshire, UK
Member Since: Jul 2007
Posts: 2096
« Reply #10 on: December 21, 2007, 08:16 PM »
Quote from: Corwin on December 21, 2007, 07:45 PM
Oh, now I'm really liking your stand!

Thanks!
Logged
Festoolian since February 2006

TS55R EBQ saw - CTL26 - CTL Mini - OF1400EBQ router - KS120 Kapex SCMS - ETS150/3 sander - RO90 sander - DF500 Domino - T12 drill

Wish list (in no particular order!): Anything not listed above....
Pages: [1]   Go Up
  Print  
« previous next »
 
Jump to: