Author Topic: Another hammer a3 31 question  (Read 4252 times)

0 Members and 1 Guest are viewing this topic.

Offline cgraham

  • Posts: 51
Another hammer a3 31 question
« on: January 07, 2017, 08:03 PM »
I have been saving for the combo jointer planer for quite sometime and am ready to move forward.....except I just got to see it in person at the Baltimore woodworking show. I never realized how low you have to bend down to feed the planer. Having back issues, I was wondering from you hammer owners do you notice how low it is or is it a non issue? Just wondering? Thanks!

Festool USA does not pre-approve the contents of this website nor endorse the application or use of any Festool product in any way other than in the manner described in the Festool Instruction Manual. To reduce the risk of serious injury and/or damage to your Festool product, always read, understand and follow all warnings and instructions in your Festool product's Instruction Manual. Although Festool strives for accuracy in the website material, the website may contain inaccuracies. Festool makes no representations about the accuracy, reliability, completeness or timeliness of the material on this website or about the results to be obtained from using the website. Festool and its affiliates cannot be responsible for improper postings or your reliance on the website's material. Your use of any material contained on this website is entirely at your own risk. The content contained on this site is provided for informational purposes only and does not constitute professional advice.


Offline RobBob

  • Posts: 1185
Re: Another hammer a3 31 question
« Reply #1 on: January 07, 2017, 08:16 PM »
It's a non-issue for me, but I do understand back problems.  Being 6'3" I prefer my workbenches and shop equipment to be taller.  Otherwise, my back starts to ache and get stiff.

However, with the planer you are not bending over for more than a few seconds at a time.  Usually, you can stand up straight while it feeds itself through the planer.  Out feed support might help with long boards, though.

Offline J0hn

  • Posts: 116
Re: Another hammer a3 31 question
« Reply #2 on: January 07, 2017, 08:55 PM »
Add a set of Zambus casters - that will add about 4" to it

http://www.zambus.com/product/ac600.php

Offline RobBob

  • Posts: 1185
Re: Another hammer a3 31 question
« Reply #3 on: January 07, 2017, 09:20 PM »
Oh, that reminds me.  I did add locking 4" casters from castercity.com to mine.  Call them and ask for help picking out the casters.

Personally, I don't like the Zambus style casters.  You practically have to get down on the floor to level it and the small wheels get hung up on cracks and debris.

A simple wedge under one wheel works better for me.  You can use your foot to slide it under the wheel.  Also, the large 4" casters sure do roll nicely on an uneven concrete floor with lots of debris. 
« Last Edit: January 07, 2017, 09:23 PM by RobBob »

Offline Wooden Skye

  • Posts: 1061
  • My little girl was called home 12-28-15
Re: Another hammer a3 31 question
« Reply #4 on: January 07, 2017, 09:47 PM »
If you don't need mobility, you could build a platform or keep on the pallet it was shipped on. 
Bryan

TS 55, (2) 1400 Guide Rails, 1900 Guide Rail, MFT/3, Domino DF 500, 2 domino systainers, ETS 150/3, RO 90, CT 26, (2) OF1400, RO 150. RTS 400, LR 32 set, PS300 jigsaw, 3 abrasive systainers, (2) sys toolbox, (2) sys mini, clamps and other accesories

Offline SouthRider

  • Posts: 94
Re: Another hammer a3 31 question
« Reply #5 on: January 07, 2017, 10:57 PM »
I'm 5'9 and 61 yr old. No back problems, but I have a bad hip & knee. Absolutely no problems using the planer on my A3-31. I don't know how comfortable I would be jointing if I added height to it.

Mine has the mobility kit (rear wheels), which I only purchased to get it off of the pallet. I don't move mine as it stays next to a dust collector drop, but it does move well with the kit.
"We, the willing, led by the unknowing, are doing the impossible, for the ungrateful. We have done so much, for so long, with so little, that we are now qualified to do almost anything, with nothing at all."

Offline HAXIT

  • Posts: 167
Re: Another hammer a3 31 question
« Reply #6 on: January 08, 2017, 12:05 PM »
I agree with out feed support is a great idea and it would not be comfortable for jointing if the machine is too high.
But before changing anything, how thick of the material are you working with usually? If you work with material up to 2" thick usually, then you should not have any problem because your thickness table is about all the way up.   

Offline sac3848

  • Posts: 39
Re: Another hammer a3 31 question
« Reply #7 on: January 08, 2017, 12:13 PM »
I have the A3 41,6 feet and 70 Added the extension and have had no problems

Offline derekcohen

  • Posts: 145
    • In The Woodshop
Re: Another hammer a3 31 question
« Reply #8 on: January 21, 2017, 08:13 AM »
I'm 5' 9 1/2" and have no problems feeding the thicknesser/planer. It is possible to do this without too much bending. However, I wonder how you will go with the winder (to raise and lower the thicknesser bed). I have the digital gauge, and one needs to get down low to sight it.

Regards from Perth

Derek